hydrotab SR Series Manuel utilisateur
Hydro
Tab
Marine Engineering
Hydrotab BT Series
SR Series & Rocker Switches Installation - Operation Manual
Hydro
Tab
Marine Engineering
2
Hydro
Tab
Marine Engineering
Disclaimer
The interceptor units are also steering
equipment and it is the sole responsibility of
the navigator-operator to ensure that, at any
point, any problem that will alter the boat's
course, rising from malfunction of
interceptors, should be dealt immediately by
the operator. At no circumstances, fault of our
interceptor equipment leading to any kind of
accident, creates liability for the
manufacturer.
Trademark Notice
Hydrotab is a registered trademark of Olympic
Engineering Ltd, Greece. All other trademarks,
trade names or company names referenced
herein are used for identification only and are
property of their respective owners.
Patent Notice
The Hydrotab products are protected by
patents and industrial design patents, patents
pending or design patents pending.
Declaration of conformity
This product conforms to the following
Electromagnetic Compatibility (EMC)
regulations and standards for use in marine
environments.
CE EN 60945
Technical information and
Documentation
The technical information provided in this
document was accurate and correct at the
corresponding production time of the
Hydrotab interceptors. Our operating principal
for improving the manufactured product, may
lead to changes regarding its specifications
without prior notice. Liability will not be
accepted for any inaccuracy considering the
product and the user manual.
Fair use statement
This manual can be printed or copied for your
own use only. Copies should not be provided
to third parties and manual should not be
commercialized.
Product Disposal
Waste removal of this product must be
according to the Waste Electrical and
Electronic Equipment (WEEE) Directive.
Product Registration
Please register your product online in order
the warranty to be valid.
3
Hydro
Tab
Marine Engineering
TABLE OF CONTENTS
Disclaimer
2
Installation Kit
4
Required Tools for Installation
5
Before Installation
5
Safety precautions
5
Proper Interceptor Installation in Transom
6
Interceptor Installation
7
Interceptor Installation (Indirect Air Supply)
9
Air Unit Installation
9
Installation Schematic overview (One Set of Rocker Switches)
11
Installation Schematic overview (Two Sets of Rocker Switches)
11
Air Unit Electrical Diagram
12
Air Unit Pneumatic Diagram
13
Spare Parts List - Model: 300SR (ASM-01269)
14
Spare Parts List - Model: 450SR (ASM-01285)
15
Spare Parts List - Air Unit (ASM-01051)
16
Troubleshooting
17
Warranty Conditions
18
4
Hydro
Tab
Marine Engineering
Installation Kit
1. Two interceptors
2. 12V Air Unit
4. Pipe 8mm
8. Screws
7. Fittings
Optional controller
Y Connector
1X 10m
Air Unit wall mounting screws (4,8x25)
Fitting mounting screws (4,8x25)
3DHC controller mounting screws (3,5x13)
Interceptor mounting screws (6,3x32)
Optional cables
20m 30m 40m
5. Connection cable
10m
Lower edge of the trim unit
Κάτω μέρος του φλαπ
Lower edge of the hull
Άκρη γάστρας
Use drill &5,5mm x 6holes
Χρησιμοποιήστε τρυπάνι &5,5mm x 6 τρύπες
SR300
Use drill Ø8.5mm
Χρησιμοποιήστε τρυπάνι Ø8.5mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Lower edge of the trim unit
Κάτω μέρος του φλαπ
Lower edge of the hull
Άκρη γάστρας
Use drill &5,5mm x 6holes
Χρησιμοποιήστε τρυπάνι &5,5mm x 6 τρύπες
SR300
Use drill Ø8.5mm
Χρησιμοποιήστε τρυπάνι Ø8.5mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Hydro
Tab
Marine Engineering
6. Two drilling patterns
3. Rocker Switches
5
Hydro
Tab
Marine Engineering
Electric saw
Drill Ø4 Drill Ø8,5
Drill Ø5,5
Drill Ø3
5mm
Allen Key No 5Screwdriver Drilling tool
Required Tools for Installation
Sikaflex gun Marking tool
(pencil or marker)
Before Installation
1. For high speed boats, overtrim may cause unexpectable turn. Improper use of trim tabs, may result to
accident or injury.
2. DO NOT PLACE YOUR FINGERS ON THE SIDES OF THE INTERCEPTORS (Figure 4). Severe injury danger!!!
Safety precautions
WARNING!
2
1
3Right
Wrong
1. For high speed boats, overtrim may cause unexpectable turn. Improper use of trim tabs, may result to
accident or injury.
2. DO NOT PLACE YOUR FINGERS ON THE SIDES OF THE INTERCEPTORS (Figure 4). Severe injury danger!!!
Safety precautions
WARNING!
4
A good hint is that the closer the units are to the water line, the best the bank control of the boat will be
(Figure 3).
Attention! Please make sure that the pipe
insertion hole is accessible from the engine room
(Figure 2).
Make sure there are no obstructions behind the
drilling area (tanks, fuel lines, cabling) which can
be damaged or prevent the installation (Figure 1).
If there is a double installation on the boat please
allow a 18 to 20 mm space between them (Figure
4).
6
Hydro
Tab
Marine Engineering
Right
Transom
Interceptor
Proper interceptor installation in transom
For maximum performance and less drag, install interceptors on the transom so blades deploy vertically.
If transom is not vertical to water plane, correct the angle by using wedges or other means.
If the boat's transom has a significant curvature, it is necessary to create a flat plane for the installation
(acceptable flatness tolerance: 2mm).
Optimal
Less performance Correct angle
More drag
wedge
Interceptor
Transom Wrong
For aluminum hulls, it is suggested Isolation Plates between hull and interceptors to be installed. You can
find installation instructions in the Isolation Plates Kit.
7
Hydro
Tab
Marine Engineering
Interceptor Installation
6
You will need
No 4 No 8,5
No 5,5
Lower edge of the trim unit
Κάτω μέρος του φλαπ
Lower edge of the hull
Άκρη γάστρας
Use drill Ø5,5mm x 10holes
Χρησιμοποιήστε τρυπάνι Ø5,5mm x 10 τρύπες
SR450
Use drill Ø8.5mm
Χρησιμοποιήστε τρυπάνι Ø8.5mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Use drill Ø4mm
Χρησιμοποιήστε τρυπάνι Ø4mm
Remove the pattern and drill according to the
pattern indications.
5
Tape
Drill all the pattern holes with a 3mm bore without
removing the pattern.
You will need
No 3
7
Apply sealant Sikaflex 291 to the holes.
You will need
Sikaflex Gun
8
Use a spatula to clean the excessive glue from the
holes.
You will need
Spatula
9For Direct Air Supply: Advise the instructions.
For Indirect Air Supply: Use the components included in the kit.
Direct air supply Optional:
Indirect Air Supply Kit
8
Hydro
Tab
Marine Engineering
Interceptor Installation
11
Mount the pipe into the drilled hole.
10
Apply Sikaflex to the interceptor.
You will need
Sikaflex Gun
M4,8x25
12
Mount the cap base to the transom. Mount the interceptor to the transom.
13M6,3x32
5mm
Allen Key No 5
Mount the front cap and tighten the screws.
14
Mount the protection cap.
15
9
Hydro
Tab
Marine Engineering
Interceptor Installation (indirect air supply)
In case of indirect air supply, you can use the components included in the kit as shown
in the image.
10
Hydro
Tab
Marine Engineering
Connect the push-in fitting
After you install the hose through the
transom, mount the air fitting into the hose.
!
5
Air Unit Installation
4
Pneumatic Connection
Cut the 8mm
pipe at the
proper length
and connect it
to the Air Unit
3
Autres manuels pour SR Series
1
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels hydrotab Équipement marin
Manuels Équipement marin populaires d'autres marques
Clarion
Clarion GR10BT Manuel de réparation
Raymarine
Raymarine Maxiview ST80 Guide de l'utilisateur
GUIDANCE MARINE
GUIDANCE MARINE 20- Series Instructions de montage
Raymarine
Raymarine ST60 Tridata Guide de l'utilisateur
olympia electronics
olympia electronics ΒS-531/1/MAR Manuel utilisateur
Sonic
Sonic 2024 Manuel utilisateur