Hybrid+ HSS CW Manuel utilisateur

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. Installation

4. How to set up the unit

5. How to control the fixture

6. DMX512 Configuration

7. DMX512 Connections

8. Troubleshooting

9. Fixture Cleaning

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

Unpack and check carefully that there is no transportation damage before using the

fixture.

Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the fixture.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Disconnect main power before servicing and maintenance.

Use safety chain when fixing this fixture. Don’t handle the fixture by taking its head only,

but always by taking its base.

Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

In the event of a serious operating problem, stop using the fixture immediately. Never

try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type of spare parts.

Do not connect the device to any dimmer pack.

Do not touch any wire during operation as there might be a hazard of electric shock.

To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

The housing must be replaced if it is visibly damaged.

Do not look directly at the LED light beam while the fixture is on.

Caution

There are no user serviceable parts inside the fixture. Do not open the housing or attempt

any repairs yourself. In the unlikely situation that your unit may require service, please

contact your nearest dealer.

Please read the instructions carefully which include important

information about the installation, operation and maintenance.

2. Technical Specifications

Light Sources: 1x 200W Warm White+ Cool White 2in1 COB Led

Channel: 5 DMX channel

Control Mode: Auto, Sound Active, Master/Slave, DMX

7 built-in performance mode

Electronic Dimming:0-100%

Fuse：F3A/250V

Power consumption：200W

Power Supply：AC100-240V, 60/50Hz

Packing size：L340×W300×H390mm

Net Weight：4.75kg

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of

the unit’s weight. Always use a safety cable that can hold 12 times of the weight of the unit

when installing the fixture.

The equipment must be fixed by professionals, and it must be fixed at a place where it is out

of reach.

4. How To Set Up The Unit

4.1 Control Panel

Button:

1MENU To go forward select menu or go back to the last level menu

②UP To go forward select menu or increase parameters

③DOWN To go backward select menu or reduce parameters

④ENTER Enter submenu

⑤Fuse

⑥Mains input：Connect to supply mains power.

⑦Mains output：Connect to supply mains power for the next unit.

⑧DMX input: For DMX512 link, use 3-pin XLR plug cable to input DMX signal.

⑨DMX output：For DMX512 link, use 3-pin XLR plug cable to link the next unit.

Note:

(1) In ten seconds, if no button was pressed, the LED display will turn off. Press any button

to turn on the LED display again.

(2) Whenever any button has been pressed, the program will save all parameter after 2

seconds

(3) No matter the program in which mode , once to detect the DMX or SLAVE signal,

the program will jump into DMX or SLAVE mode automatically. Then if DMX or SLAVE

signal was disconnect , the program will return to the original mode.

4.2 Main Function

5. How to control the fixture

There are three ways to control the fixture

A. Universal DMX controller

B. Master/Slave operation

C. Controller

A. Universal DMX controller

The fixture can be set to the DMX address remotely by the universal DMX controller. First,

you need to program two scenes into a chase, then link the fixtures to the universal DMX

controller. When you run the chase, all the fixtures of the chain will be set to the series DMX

address automatically. The fixture uses four channels. Please refer to the following diagram

to set the address for the first four units.

B. Master/Slave operation

The fixture will allow you to link 16 fixtures together and operate without a controller. In

Master/Slave mode, the first fixture will control the others to give an automatic, sound

activated, synchronized light show. This function is good when you want an instant show.

The first fixture’s DMX input cable will have nothing to connect it, and the other fixtures will

be set in slave mode automatically. Their DMX input cables must be connected to the last

fixture DMX output cable (daisy chain). Any fixture can act as a Master or as a Slave

Channels mode

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

CH5

6. DMX512 Configuration

Channel

Value

Function

CH1

0-5

Dimming mode

6-180

Auto Run Macro 1 ~ Macro7

181-205

sound mode 1

206-230

sound mode 2

231-255

sound mode 3

CH2

0-255

Master dimming (CH1<6)

0-255

Auto Run speed (CH1=6~180)

0-255

Sound Sensitivity (CH1>180)

CH3

0-255

Stroboscopic speed

CH4

0-255

Cool white dimmer

CH5

0-255

Warm white dimmer

7. DMX512 Connections

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. If you are using a controller with a 5 pin DMX output, you need to use a 5 to 3

pin adapter-cable.

2. Connect the fixture together in a “daisy chain” plug XLR cable from the output of

the fixture to the input of the next fixture. The cable cannot be branched or split

to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

3. The DMX output and input connectors are pass-through to maintain the DMX

circuit when one of the units’ power is disconnected.

4. At the last fixture, the DMX cable has to be terminated with a terminator to

reduce signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and

pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last

fixture.

5. Each lighting fixture needs to have an address set to receive the data sent by

the controller. The address number is between 0-511 (usually 0 & 1 are equal to

1).

6. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)

5 pin XLR: Pin1: GND, Pin2: Negative signal (-), Pin3: Positive signal (+)

Pin4/5: Not Used.

8. Troubleshooting

The following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The fixture does not work, It has no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, and cables to see if they are

linked properly.

2. If the DMX LED is on and there is no response to the channel, check the address

settings and DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on the connectors or on the

PCB of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the fixture. Set the proper address.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone by tapping the microphone.

9. Fixture Cleaning

Internal cleaning must be carried out periodically to optimize light output. Cleaning

frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surroundings can cause greater accumulation of dirt on the fixture’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hybrid+ Matériel de DJ

Hybrid+

Hybrid+ HMH 7 Manuel utilisateur

Hybrid+

Hybrid+ HSS 6.4B Manuel utilisateur

Hybrid+

Hybrid+ HMN 285 Manuel utilisateur

Hybrid+

Hybrid+ HSF12.4 Manuel utilisateur

Hybrid+

Hybrid+ HMH 12 Manuel utilisateur

Hybrid+

Hybrid+ FOUR BEAM Manuel utilisateur

Hybrid+

Hybrid+ TRIPLE DERBY Manuel utilisateur

Hybrid+

Hybrid+ HMH100B Manuel utilisateur

Hybrid+

Hybrid+ HMH GOBO II Manuel utilisateur

Hybrid+

Hybrid+ HS 1500 Manuel utilisateur

Hybrid+

Hybrid+ HSS 12.6 Manuel utilisateur

Hybrid+

Hybrid+ MUSHROOM Manuel utilisateur

Hybrid+

Hybrid+ DMX-384 Manuel utilisateur

Hybrid+

Hybrid+ HMH 230 Manuel utilisateur

Hybrid+

Hybrid+ HSS COB4B Manuel utilisateur

Hybrid+

Hybrid+ CM3UFX Manuel utilisateur

Hybrid+

Hybrid+ HH3000 Manuel utilisateur

Hybrid+

Hybrid+ HMH GOBO Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur