Huzzard CR1000 Manuel utilisateur
Using the CR1000 in a Universal Stand
Hardware Revisions 4+ of the CR1000s have a stand detecon
feature. By default, when the CR1000 is placed in the stand, the
reader will automacally enter into moon detecon mode.
When in this mode, simply place a bar code in the scan eld to
acvate the reader. The CR1000 will beep and ash a green LED
to indicate a ‘good read’ has occurred.
For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device. Aer
several seconds, the reader will beep twice and the LED will turn o to indicate the CR1000 is
ready for use.
For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into
the barrel jack of the cable, and connect the RS232 connector to the appropriate serial port on
the host device. Aer several seconds, the reader will beep twice, the reader will vibrate and
the LED will turn o to indicate the CR1000 is ready for use.
Using the CR1000 Out of a Universal Stand
Powering on the CR1000
The default seng on the CR1000 has Sux Enter disabled. To enable Sux Enter, please
scan the following conguraon code:
CR1000 Default Sengs
Aztec
Codabar
Code 39
Data Matrix Rectangle
All GS1 DataBar
Interleaved 2 of 5
Code 93
Code 128
Data Matrix
PDF417
QR Code
UPC/EAN/JAN
The CR1000, out of the box, will read the following bar codes:
To congure a CR1000 to read bar codes not listed, please download the CR1000
Conguraon Guide from www.codecorp.com and scan the appropriate ‘Enable’ bar code
reading symbology conguraon code.
Sux Enter Conguraon
Sux Enter - USB Carriage Return, Line Feed - RS232
For more conguraon opons, download the CR1000 Conguraon Guide from
www.codecorp.com.
Serial #: 20000XXXX
MFG #: CR1011_04
Designed in USA.
Made in Malaysia.
Determining the Hardware Revision of a CR1000
Locate the Serial Label on the reader to idenfy the hardware revision. CR1000 readers with
a MFG # of _04 (or higher) have the stand detecon mode.
_04 indicates
revision 4 hardware
2 3
Hardware Revisions 1-3 of the CR1000s do not have an automac stand detecon feature to
enable moon detecon reading when the CR1000 is in a stand. To congure these hardware
revisions for moon detecon scanning, please refer to the CR1000 Conguraon Guide,
located at www.codecorp.com and scan the appropriate code.
Press and hold the CR1000 trigger buon, the two blue bars
eming from the reader are used for targeng. Center the
blue bars in the middle of a bar code.
The opmal reading distance from reader to bar code is
approximately 4.0” (10 cm).
Once the reader is at the opmal distance, the CR1000 will read the bar code (when the
buon is pressed). The CR1000 will beep and ash a green LED to indicate a ‘good read’ has
occurred.
When the CR1000 is removed from the stand, the reader switches to manual mode and the
buon must be pressed to read a bar code.
www.codecorp.com www.codecorp.com
Quickstart Guide
C005747_06_CR1000_Quickstart_Guide
Code Reader™ 1000 (CR1000)
USB Anity® Cable RS232 Anity® Cable
w/ Power Supply
Aaching/Detaching a Cable
To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader
(Figure 1). Firmly push the connector into the reader unl a snap can be heard, to
indicate the cable is properly aached. To detach a cable, press a paper clip into the
hole on the back of the CR1000 (Figure 2), and gently pull the cable from the reader.
Figure 2Figure 1
Included with your CR1000
Depending on the kit ordered, the following may have been shipped with your reader:
Universal Stand
Universal Stand Assembly (included when ordered as a Kit/Package)
Cleaning a CR1000
The following agents are approved to clean a Code bar code reader:
• Alcohol Wipes
• Clorox® Disinfecng Wipes
• Clorox® Bleach Soluon (10% Clorox bleach, 90% tap water)
• Medical DiAirKem
• Sani-Cloth® HB, Super Sani-Cloth® Germicidal, Sani-Cloth® Plus Germicidal
Disposable Wipes
• Virex® II Disinfectant Cleaner
© 2013. Code Corporaon. All Rights Reserved. 4
Autres manuels Huzzard Lecteur de codes-barres
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
