Huskie Tools EP-410HT Mode d’emploi

Operating Instruction Manual

For EP-410HT Compression Tool

with Parts List

HUSKIE TOOLS, INC.

http://www.huskietools.com [email protected]

EP-410HT SPECIFICATIONS

Keep Fingers Out Of Pinch

Areas

Always Wear Safety Glasses

Do Not Operate Without Dies The User Should Be Properly

Trained in the Correct

Procedures Required For Work

Around Electrical Lines.

12 TON TITANIUM C-HEAD

1” JAW OPENING

SPECIFICATIONS

CONNECTOR RANGE

•Extremely Light Weight Titanium

•Ideal for Hot Stick Applications

•All the Same Features as the EP-410H Model

Output 12 ton

Weight 5 lbs.

Length 10"

Jaw Opening 1"

Lugs #8-750 MCM

Splices #10-400 MCM

http://www.huskietools.com [email protected]

GENERAL INFORMATION AND TROUBLESHOOTING

1. Before connecting the tool head, make sure the pump and hose being used is working properly, and

adjusted to and rated at 10,000 psi. The use of a pump or hose not rated at 10,000 psi working pressure

may cause severe damage and result in personal injury.

2. Connect the tool head to the pump and hose, making sure all coupler connections are secure. It is

important that all connections are tight for tool to function properly.

3. Select appropriate compression die set for the connector and cable being used. The “U” style Huskie HT-41

series dies are to be used with these tools.

4. To insert the dies, depress the die release pin on the ram, and slide die into place. Then lift release knob on

top of “C” head and slide other die half in place. Be sure both die halves are secure before operating the

tool.

5. Position the connector between the dies and operate pump to hold connector in place. Fully insert

cable into the barrel of the connector and operate pump as described in the pump operations manual

until connector is fully crimped. For pumps that are not equipped with a hold feature, connector and

cable must be in alignment before operating the pump.

6. Always be sure to keep couplers clean and caps in place when the tool is not being used.

OPERATING INSTRUCTIONS FOR THE EP-410HT

1. Never operate tools without dies in place. Failure to insert dies before operation will cause damage to the

“C” frame and tool ram.

2. Never attempt to adjust pressure setting without the use of the proper test gauge. Consult factory for proper

adjusting procedure.

3. Die hang up is common with all types of compression tools. Should this occur, the jaws can easily be

separated by holding the pump in the release position while prying the jaws apart. Never attempt to hit

connector or tool jaw with hammer as this will damage connector and tool.

4. Always clean tool after use to keep ram track clear of dirt and debris.

http://www.huskietools.com [email protected]

MODEL EP-410HT DIAGRAM

http://www.huskietools.com [email protected]

MODEL EP-410HT PARTS LIST

NO. DESCRIPTION CODE QTY NO. DESCRIPTION CODE QTY

1 2 X 14 DRIVE PIN 75-33 1

2 KNOB HR-113 2

3 SCREW (16) 510-02 1

4 SPRING (257) 510-03 1

5 RETAINER PIN (A) HR-114 1

6 2.5 X 24 DOWEL PIN 40U-08 1

7 HEAD (TITANIUM) 410-01T 1

8 KEY 510A-06 1

9 M5 LOCK WASHER (SMALL) 510-12 1

10 GUIDE SCREW 510A-15 1

11 STOPPER 410H-01 1

12 M5 LOCK WASHER 410-09 1

13 M5 X 10 SCREW 410H-02 1

14 RAM (LUBNIK) 410-13L 1

15 SPRING (177) 410-01 1

16 RETAINER PIN (B) 410-12 1

17 2.5 X 14 DRIVE PIN (BW) 410-11 1

18 DIE RELEASE PIN (B) 410-14 1

19 2.5 X 8 DOWEL PIN (B) 410-17 1

20 DUST SEAL 430-03 1

21 P-40 BACK-UP RING (B.C.) 22-16 1

22 P-40 0-RING (C.P.) 410-70 1

23 RAM SPRING GUIDE 410-18 1

24 SPRING (65) 410-19 1

25 RAM SPRING SUPPORT 410-20 1

26 GV-36 SNAP RING 410-21 1

27 CYLINDER 410-03T 1

28 ADAPTER 3/8" PT-M 3/8"NPT-F Y30-25A 1

29 GRIP Y30-26 1

30 FEMALE COUPLER FC-8/DP-8 1

All Huskie REC-Series battery driven products carry a 5 year warranty, and the ECO-Series

carry a 3 year warranty. The BP-70E, BP-70EI, and the BP-70MH batteries carry a 5 year

warranty from the date stamped on the battery. The LED indicator on the BP-70-EI battery

carries a 1 year warranty from purchase date. Hydraulic hammers carry a one year warranty

and all other Huskie products carry a 5 year warranty. Huskie reserves the right to determine

all warranty claims. Failure due to misuse, abuse or repairs attempted by anyone other than

Huskie Tools, Inc., or an authorized service center render this warranty null and void. Our

patented drop-out bypass cartridge can be re-calibrated or tested at no charge for the life

of the tool. All factory repaired or reconditioned hydraulic tools carry a one year warranty

on parts and labor.

REPAIR AND WARRANTY CLAIMS

All claims must be sent to Huskie for inspection and authorization. A Return Goods

Authorization is required before shipping tools to Huskie. Secure the authorization by

telephoning 1-800-860-6170 or writing to Huskie's main office with details of claim. Non-

warranty repairs are handled using the same procedure. Repairs exceeding 50% of the cost

of a new tool will be advised before repairs are made.

PLEASE RETAIN FOR YOUR RECORDS

Purchaser’s Name _____________________________________________________

Address _____________________________________________________

City, State, Zip _____________________________________________________

Tool Model Number _____________________________________________________

Serial Number _____________________________________________________

Date Purchased From _____________________________________________________

Purchased From _____________________________________________________

MODEL EP-410HT WARRANTY

HOW TO GET SERVICE UNDER THE TERMS OF THE LIMITED WARRANTY

Return your product directly to Huskie Tools, Inc. as our representative network is not

prepared to service the product under the terms of this warranty.

1. Write, call or fax Huskie stating the tool’s purchase date and problem. You will be

given a RGA # to assure that your merchandise will be properly handled upon its

receipt.

2. CAUTION: Make sure the product is packaged adequately so as to prevent damage

or loss during transit. The shipment must be prepaid and we recommend that it be

insured. A cover letter indicating the reason for the return should be included in

order to facilitate repairs.

SEND THIS PORTION WITH ANY TOOL WHEN REQUESTING REPAIRS,

WARRANTY OR RECONDITIONING WORK.

PLEASE CALL OR FAX HUSKIE FOR AN RGA#

Customer Job No. _______________________

Address________________________________

City___________________________________ State _____ Zip _____

Tool Model ____________________________

Warranty Claim _____ Repair Only ____

Customer Name:____________________

Phone ( _____ ) ________________________

City___________________________________ State _____ Zip _____

Serial No. _________________________

Estimate Required: Yes _____ No _____

MODEL EP-410HT WARRANTY

198 N. Brandon Drive

Glendale Heights, Illinois 60139

(630) 893-7755 Fax (800) 345-3767

Toll Free 1-800-860-6170

http://www.huskietools.com

[email protected]

Table des matières

Autres manuels Huskie Tools Outils

Huskie Tools

Huskie Tools ECO-MK7EZ Manuel utilisateur

Huskie Tools

Huskie Tools REC-B6430 Manuel utilisateur

Huskie Tools

Huskie Tools CN-258 Mode d’emploi

Huskie Tools

Huskie Tools R-750C Manuel d'installation

Huskie Tools

Huskie Tools EP-410H Manuel utilisateur

Huskie Tools

Huskie Tools ECO-MK7336B Manuel utilisateur

Huskie Tools

Huskie Tools EP-410 Manuel utilisateur

Huskie Tools

Huskie Tools EP-510C Mode d’emploi

Huskie Tools

Huskie Tools Pro Line 7 Series Manuel utilisateur

Huskie Tools

Huskie Tools REC-B6510K Manuel d'installation

Huskie Tools

Huskie Tools REC-6630 Manuel d'installation

Huskie Tools

Huskie Tools REC-5510 Mode d’emploi

Huskie Tools

Huskie Tools PRO LINE REC-MK7430 Manuel utilisateur

Huskie Tools

Huskie Tools CN-58H Manuel utilisateur

Huskie Tools

Huskie Tools CN-258 Manuel utilisateur

Huskie Tools

Huskie Tools EP-510C Manuel utilisateur

Huskie Tools

Huskie Tools REC-Y33M Manuel utilisateur

Huskie Tools

Huskie Tools IL-MK7ND Manuel utilisateur

Huskie Tools

Huskie Tools SL- 610 Manuel utilisateur

Huskie Tools

Huskie Tools EP-510HK Mode d’emploi

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser