Hunter 10” Manuel utilisateur

10” Opal Schoolhouse Globe Light Kit

Installation Instructions

43506-01 r031407

IMPORTANT: Read all warnings before you begin.

CAUTIONS

• Read entire installation instructions carefully before beginning installation and save these instructions.

• To avoid possible risk of electrical shock and fire, install this light fixture only on Hunter ceiling fan Type

A-Z. Find the fan model number on the fan package or on the nameplate on top of the motor housing.

WARNINGS

• To avoid possible electrical shock, before installing light fixture disconnect power by turning off the

circuit breakers both to the outlet box and to its associated wall switch location. If

you cannot lock the circuit breakers in the off position, securely fasten a prominent

warning device, such as a tag, to the service panel.

• Connect house wiring to the fan before attaching the light fixture to the fan.

• All wiring must be in accordance with national and local electrical codes. If you are

unfamiliar with wiring, you should use a qualified electrician. Professional installation is recommended.

• To reduce the risk of fire or personal injury, allow bulbs and surrounding surfaces to cool to room

temperature before touching or removing them.

is light ﬁxture is for use only on Hunter Ceiling Fans Type A-Z.

is light ﬁxture weighs 4.45 pounds.

is manual contains installation instructions for the following types of fans:

• Fans With Removable Switch Housing

• Fans With Non-Removable Switch Housing

• Fans With Non-Removable Switch Housing and No Center Hole

Preparing to Install the Light Kit

1. Disconnect power to the ceiling fan by turning oﬀ the circuit breakers both to the outlet box and to any associated wall

switch locations.

43506-01 r0314072

Installing the Light Kit on Fans with Removable Switch Housings

1. Unscrew the three screws from the upper switch housing. Disconnect

the 9-pin plug connectors. Remove the lower switch housing.

2. Push the plug button from inside the lower switch housing to remove

the plug button and switch housing cap. Unscrew the two attachment screws on the

bottom of the switch housing.

NOTE: Save the plug button and switch housing cap should you choose to remove

the light ﬁxture in the future.

3. Feed the two wires from the light kit up through the center hole in the lower switch

housing.

CAUTION: If your fan is operated by remote control, take care not to damage

the small components on the circuit board inside the housing.

Align the keyholes of the light kit and the screw holes of the lower switch housing.

Install the nut and washer onto the threaded rod from the light kit.

Finish attaching the light kit to the lower switch housing. Use the two attachment

screws removed from the lower switch housing and the lock washers on the red

tag. Partially install the screws into the light kit and the housing. Rotate the housing

counterclockwise until the screws are locked into the narrow ends of the keyhole

slots. Securely tighten the two screws.

WARNING: Improper installation could cause the light ﬁxture to fall, or result

in electrical shock or personal injury.

4. Remove the wire nuts from the two wires in the switch housing labeled “Connect

Light Here” or “For Light Use.”

Connect the black/white striped wire from the switch housing to the black wire from

the light kit. Connect the white wire from the switch housing to the white wire from

the light kit. Secure all wire connections using wire nuts.

To connect the wires, hold the bare metal leads together and place a wire nut over

them, then twist the wire nut clockwise until tight.

CAUTION: Be sure no bare metal

wires or wire strands are visible after

making the connections.

5. Reconnect the 9-pin plug connector.

6. Install screws to reattach the lower

switch housing to the upper switch

housing.

7. Go to the instructions for Installing

Bulbs, Chains, Shades.

Removable Switch Housing

9-Pin Plug

Connector

Lower Switch

Housing

Attachment

Screw

Plug

Attachment

Screws and

Lockwashers

Wires and

Wire Nuts

9-Pin Plug

Connector Screw

43506-01 r031407 3

Steps 4–6

Steps 1–2

Step 3

Screw

Installing the Light Kit on Fans with Non-Removable Switch Housing

1. Uninstall the two screws from the switch housing cover.

2. Remove the plug or screw from the center of the switch housing

cover.

3. read the switch housing cover onto the wires from the light kit. Align the large

ends of the keyholes in the light kit with the screw holes in the switch housing cover.

Install the nut and washer onto the threaded rod from the light kit to secure the

switch housing cover.

4. Finish attaching the light kit to the switch housing cover. Use the two attachment

screws removed from the lower switch housing and the lock washers on the red

tag. Partially install the screws into the light kit and the housing. Rotate the housing

counterclockwise until the screws are locked into the narrow ends of the keyhole

slots. Securely tighten the two screws.

WARNING: Improper installation could cause the light ﬁxture to fall, or result

in electrical shock or personal injury.

5. Remove the wire nuts from the two wires in the switch housing labeled “Connect

Light Here” or “For Light Use.” One wire is white and the other wire is black/white

striped.

Connect the black/white striped wire from the switch housing to the black wire from

the light kit. Connect the white wire from the switch housing to the white wire from

the light kit. Secure all wire connections using wire nuts.

To connect the wires, hold the bare metal leads together and place a wire nut over

them, then twist the wire nut clockwise until tight.

CAUTION: Be sure no bare metal wires

or wire strands are visible after making the

connections.

6. Align the locator posts in the switch housing

cover with the screw holes in the switch

housing.

7. Align the threaded screw holes in the switch

housing cover with the threaded holes in the

switch housing and install two screws.

8. Go to the instructions for Installing Bulbs,

Chains, Shades.

Steps 1–2

Step 3–4 Steps 5–7

Non-Removable Switch Housing

Switch

Housing

Cover

Plug

Nut and

Washer

Screw

Hole

Switch

Housing

Cover

Wires and

Wire Nuts

Screw

43506-01 r0314074

Light Kit

Mounting

Plate

Installing the Light Kit on Fans With Non-Removable Switch Housing

and No Center Hole

1. Uninstall the two screws from the switch housing.

2. Remove the wire nuts from the two wires in the switch housing labeled

“Connect Light Here” or “For Light Use.” One wire is white and the other wire is

black/white striped.

Connect the black/white striped wire from the switch housing to the black wire from

the light kit. Connect the white wire from the switch housing to the white wire from

the light kit. Secure all wire connections using wire nuts.

To connect the wires, hold the bare metal leads together and place a wire nut over

them, then twist the wire nut clockwise until tight.

CAUTION: Be sure no bare metal wires or wire strands are visible after making

the connections.

3. Finish attaching the light kit to the switch housing. Use the two screws removed

from the switch housing and the lock washers on the red tag. Partially install the

screws into the light kit and the housing. Rotate the light ﬁxture clockwise until the

screws are locked into the narrow ends of the keyhole slots. Securely tighten the two

screws.

WARNING: Improper installation could cause the light ﬁxture to fall, or result

in electrical shock or personal injury.

4. Go to the instructions for Installing Bulbs, Chains, Shades.

Step 1 Step 2 Step 3

Hunter original and non-

removable switch, no center hole

Switch

Housing

Plate

Wires and

Wire Nuts

Screw

43506-01 r031407 5

Light Kit

Mounting Plate

Screws

and

Washers

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38114

Troubleshooting

Light does not come on.

1. Make sure bulbs are installed properly and ﬁlament is not blown.

2. Make sure breakers or fuses are on.

3. Verify that the light power lead is connected at the ceiling. Refer to

your ceiling fan manual for locating assembly and wiring.

Glass rattles.

1. Make sure the glass globe is secure.

For other problems or questions, contact the

Hunter Fan Company Technical Support at

US 888-830-1326 / Canada 866-268-1936.

http://www.hunterfan.com

Installing Bulbs, Chains, Shades

1. Install one 19-watt compact ﬂuorescent light bulb (included) into the socket.

2. Loosen the three thumb screws in the light kit. Raise the glass globe to the light

ﬁxture, ﬁtting the rim into the louvered edge. Ensure that the top edge of the globe

clears the screws. Hand tighten the thumb screws.

3. Attach the provided breakaway connector onto the end of the pull chain.

4. e installation is complete and you can restore power to the ceiling fan.

Steps 1–4

43506-01 r0314076

Table des matières

Autres manuels Hunter Éclairage domestique

Hunter

Hunter Bullet Spotlight Kit Manuel d'instructions

Hunter

Hunter Floating Glass Light Kit Manuel utilisateur

Hunter

Hunter Marine II Manuel d'instructions

Hunter

Hunter Tea Stain Bowl Light Kit Manuel utilisateur

Hunter

Hunter MM288PU Manuel du propriétaire

Hunter

Hunter Tribeca Light Kit Tribeca Light Kit Manuel d'instructions

Hunter

Hunter Casbah Light Kit Manuel utilisateur

Hunter

Hunter Dual Function Bowl Light Kit Manuel d'instructions

Manuels Éclairage domestique populaires d'autres marques

JONATHAN Y

JONATHAN Y JYL5019A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL6007A Manuel utilisateur

Philips

Philips Ledino 31606/11/16 Manuel utilisateur

Salus

Salus UG600 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Manuel utilisateur

Philips

Philips Ledino 16811/87/16 Manuel utilisateur

Philips

Philips 405441213 Manuel utilisateur

Philips

Philips Halogen Light Manuel utilisateur

Pentair

Pentair GLOBRITE Manuel utilisateur

Philips

Philips 55592-30-16 Manuel utilisateur

Livoo

Livoo Night light Manuel utilisateur

Schwaiger

Schwaiger NFL45 Manuel utilisateur

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Manuel utilisateur

MOOD

MOOD CORSIN JY-16 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL8019 Manuel utilisateur

XTRASUN

XTRASUN XTDEOKT1 Manuel utilisateur

Inspire

Inspire Lana YF3306-M Manuel d'entretien