Hunter 90437 Manuel utilisateur

Classic Tripod FanClassic Tripod FanClassic Tripod Fan

Owner’s Manual

English

Model

90437

90440

61903-01

R20141230

TABLE OF CONTENTS

Introduction ............................................................. 3

Safety and Warnings................................................ 3

Grounding............................................................... 5

Fused Plug ............................................................... 6

Unpacking............................................................... 7

Tripod Assembly....................................................... 7

Attaching Motor To Pole ........................................... 7

Grill Assembly ......................................................... 8

Operation.............................................................. 10

Off / Speed Selection

Oscillation 10

Height Adjustment

Maintenance.......................................................... 11

Technical Support................................................... 12

Troubleshooting ......................................................12

Warranty............................................................... 12

61903-01 R20141230

INTRODUCTION

READ AND SAVE THESE INSTRUCTIONS! To reduce

electrical appliances, basic precautions should always

be taken to reduce the risk of electric shock and

personal injury:

Read all instructions before using this fan.

1. Improper installation may result in the risk of

electric shock or personal injury.

2. To prevent the risk of and electric shock, DO

NOT use the unit near windows. Rain and moisture

may create an electrical hazard.

3. The power plug must be removed from the power

socket when not in use, before cleaning, servicing,

maintenance and before moving to another location.

4. DO NOT put fan in a damp place or where humidity

is high, such as a bathroom.

5. The fan should be placed on a stable surface to

avoid overturning.

6. Use fan only for intended use, as described in this

instruction manual.

7. To protect against electrical shock, DO NOT immerse

any part of the unit in water or spray with liquids.

Thank you for choosing the Hunter Oscillating Stand

Fan. This manual gives you complete instructions for

assembling and using your fan. Here are some ofthe

features you will enjoy with your fan:

An attractive design that enhances any decor

A power

Three speeds to adjust your comfort level

All metal construction

SAFETY AND WARNINGS

61903-01 R20141230

with any solid-state speed control device. When using

8. Close supervision is necessary when any appliance

is used near children.

9. NEVER insert fingers, pencils or any other objects

through the grill when the fan is running.

10. DO NOT operate any appliance with a damaged

cord or plug, after the appliance malfunctions or has

been dropped or damaged in any manner.

11. To disconnect, grip plug and pull from wall outlet.

NEVER yank on cord.

12. ALWAYS use on a dry surface.

13. This product is intended for household use only and

not for commercial or industrial use.

14. DO NOT operate fan in the presence of explosive

and/or flammable fumes.

15. DO NOT place fan or any parts near an open flame,

cooking or any other heating appliances.

16. DO NOT use near curtains, plants, window

treatments, etc.

17. This appliance has a grounded three-prong plug

and is suitable for grounded receptacle use only.

An adapter is available for connecting three-blade

grounding-type plugs to two-slot receptacles. The

adapter must be properly grounded. DO NOT

attempt to defeat the purpose of this safely feature.

18. The rubber feet on this product may interact with

wood and cause damage to furniture. Do not place

on fine wood furniture.

61903-01 R20141230

Figure 1

This appliance is for household use only and may be

plugged into any 120-volt AC electrical outlet (ordinary

household current). DO NOT use any other type of outlet.

This unit is suitable for grounded receptacle use only.

The power cord has a groundedplug as shown in

Figure 1, and must be usedwith an electrical outlet that

can accommodate the grounding pin. If your electrical

must purchase an adapter as shown in Figure 2.

NOTE: The adapters ARE NOT supplied with this fan.

Read, follow, and save the instructions that are included

with the adapter you choose. The green grounding lug

extending from the adapter must be connected to a

permanent ground such as a property grounded outlet

accommodate the grounding pin.

LINE CORD SAFETY TIPS

1. NEVER pull or yank on the cord or the appliance.

3. To disconnect the appliance, grasp the plug and

remove it from the outlet.

4. Before each use, inspect the line cord for cuts and/

or abrasion marks. If any are found, the appliance

should be serviced and the line cord replaced. Please

return it to our Service Department or to an authorized

service representative.

5. NEVER wrapthe cord tightlyaround the

appliance, as this could place undue stress onthe

cord where it enters the appliance and couldcause

it tofray and break.

6. DO NOT operate appliance if the line cord shows any

damage, if the appliance works intermittently or stops

working entirely.

Grounded

Plug

Grounding Pin Grounded Outlet

Box Cover

WARNING

Figure 2

Grounded Outlet

Box Cover

Metal

Screw

Adapter

Grounding

Means

GROUNDING

61903-01 R20141230

outlet cannot accommodate the grounding pin, then you

box. Do not use an adapter if your electrical outlet can

Figure 3

This plug is a safety feature. It contains a safety device

(fuse) that should not be removed. Discard product if the

attachment plug is damaged. To reduce the risk of re,

electric shock and personal injury, DO NOT remove,

replace, repair or tamper with the originally supplied

to the safety device incorporated in this plug.

If the fuse fails, it is generally due to a short circuit or

circuit overload. Replace the fuse as per the instructions

below. If the replacement fuse fails, immediately

unplug the unit and contact our technical support

department for assistance.

Fuse Replacement:

1. To replace the fuse, rst turn the unit it off and unplug

it from the wall. Locate the door on top of the plug.

Figure 3.

2. Slide the door on top of the plug towards the blades.

Figure 4.

3. Carefully remove the fuse from the clips holding it on

the top and bottom. Figure 5.

Warning! Electrical Hazard! Only replace with a

fuse type and rating matching what was removed from

the product. If the product fails a second time,

immediately unplug it and contact our technical support

at 1-888-880-3267.

4. Gently push the fuse back into the pins that will hold

it in place.

Note: If the fuse is not seated properly, the unit will not

function.

6. Plug the fan back in and resume use.

FUSED PLUG

Figure 4

Figure 5

61903-01 R20141230

plug. If the fan does not function properly, it may be due

Slide the door back over the fuse box in the plug.

TRIPOD ASSEMBLY

Figure 7

1. Loosen the three lower bolts and nuts from the Tripod

2. Tighten all upper and lower bolts and nuts using

10 mm wrenches.

3. Take the setscrew out of the plastic bag that was

attached to the foam of motor housing. Extend the

inner pole and install the setscrew into the screw hole

on the inner pole. Figure 7.

UNPACKING

As you unpack the fan, save the carton and packing

materials in case you want to move or ship the unit in the

future. Carefully remove all items from the box.

NOTE: It is best to have someone hold the box while

you lift the fan and the protective packaging out of the

carton. Make sure all shipping materials are removed

from fan before operating.

Setscrew

Inner Pole

Figure 8

Clip Button

1. Press the clip buttons in completely while sliding the

pole from the motor housing assembly into the inner

pole until the clip buttons appear through the hole in

the inner pole. Figure 8.

61903-01 R20141230

ATTACHING MOTOR TO POLE

Motor

Figure 6

Lower Bolt

Upper Bolt

the three lower bolts and nuts. Figure 6.

and save them. Fully extend the legs and install back

Figure 9

Figure 11

Figure 12 Figure 13

Grill Lines

Grill

Mounting

Screw

Top Tabs

12a

Motor

Notch

Fan Blade

123

61903-01 R20141230

GRILL ASSEMBLY

Note: The grill ring may be attached to the rear grills for

shipping purposes. If so, remove the grill ring by loosening

the grill ring screw.

1. Remove the four rear grill mounting screws from the

2. Make sure that the rear grill is positioned so that

three of the grill lines are completely between the top

the back of the grill to the four screw holes on the

front of the motor.

partially install the four grill mounting screws.

Note: One of the grill mounting screws will have a star

washer on it, for grounding purposes. The other 3 screws

will not have a washer.

4. Loosen the screw on the back of the blade assembly.

Figure 12a. Slide the blade assembly onto the

5. Tighten the screw on the blade assembly to secure it

to the motor. Make sure that the end of the screw is

Caution: Ensure when tightening the screw on the back

of the fan blade, you tighten it on the ﬂat part of the

motor shaft.

To attach the rear grill to the motor housing

the motor housing, and line up the four tabs on

motor housing. Figure 9.

tabs, Figure 10. Then place the rear grill against

Tighten all four screws. Figure 11.

motor shaft. Figure 12.

positioned within the notch on the shaft. Figure 13.

Figure 10

Figure 15

Figure 14

Figure 16

GRILL ASSEMBLY CONT.

Front Grill

Hunter Logo

Grill

Ring

Screw

6. Remove the grill ring from the front grill by loosening

the screw holding it.

Hunter logo faces right side up and push together until

8. Expand the grill ring by loosening the screw that

10. Tighten the screw to secure the grill ring over both

61903-01 R20141230

bottom.

turning the ring so that the screw is on the

Place the front grill against the rear grill so that the

Slide the grill ring over both front and rear grills

Rear Grill

the tabs on the grills hold them together. Figure 14.

secures it. Figure 15.

Figure 15.

the front and rear grill. Figure 16.

Figure 17

High

Medium

Low

Oﬀ

Figure 18

OPERATION

Turn the fan “ON” or “OFF” by moving the power/speed

lever. The power should always be OFF before

unplugging the fan. Toselect the speed, move the power/

speed lever from OFF to the desired speedsetting: O (off),

I(low), II (medium), III (high). Figure 17.

Oﬀ / Speed Selection

Height Adjustment

scillation

To adjust the height of the fan, turn the adjustment knob

counter-clockwise to loosen the inner pole. Adjust the

inner pole to the desired height, and ﬁrmly tighten the

adjustment knob in a clockwise direction. Figure 19.

o allow the fan to oscillate, push the knob beside the fan

speed control down. Pull up on the knob if oscillation is

not desired. Figure 18.

Oscillation

Knob

61903-01 R20141230

Figure 19

Adjustment

Knob

Autres manuels pour 90437

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hunter Ventilateur

Hunter

Hunter MODEL TYPE A 41535-01 Manuel d'instructions

Hunter

Hunter 52228 Manuel utilisateur

Hunter

Hunter 51583 Manuel utilisateur

Hunter

Hunter 42701-01 Manuel utilisateur

Hunter

Hunter Dante MB531 Manuel utilisateur

Hunter

Hunter 90626-WH Manuel utilisateur

Hunter

Hunter Fanaway 59085 Manuel d'instructions

Hunter

Hunter B Manuel d'instructions

Hunter

Hunter 28839 Manuel utilisateur

Hunter

Hunter 28072B Manuel

Hunter

Hunter 25522 Manuel utilisateur

Hunter

Hunter Camille Manuel d'instructions

Hunter

Hunter 82022 Manuel utilisateur

Hunter

Hunter Gilmour Manuel utilisateur

Hunter

Hunter Type 3 Models Manuel utilisateur

Hunter

Hunter 21117 Manuel

Hunter

Hunter Donegan Manuel utilisateur

Hunter

Hunter 28607 Manuel

Hunter

Hunter 43041-01 Manuel utilisateur

Hunter

Hunter 21117 Mode d’emploi

Hunter

Hunter Bolivar Manuel utilisateur

Hunter

Hunter Nomad Manuel utilisateur

Hunter

Hunter 21421 Manuel

Hunter

Hunter 26106 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage

Litex Industries

Litex Industries E-CGL52CB5C1 Manuel utilisateur

Lindab

Lindab LTDF Manuel utilisateur