Hunter 43044-01 Manuel utilisateur

43044-01 03/05/2008

Installation Guide

Energy Star Bath Fan Models 82033

READ and SAVE THESE INSTRUCTIONS

ENGLISH

See page 2

ESpañoL

Vea la página 19

43044-01 03/05/2008

1) Read all instructions before attempting to install or use this appliance. This appliance is for general ventilating

use only. Do not use this appliance for ventilating hazardous or explosive materials. Follow the heating equipment

manufacturer’s guideline and safety standards, such as those published by the National Fire Prevention Association

(NFPA), and the American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the

local code authorities.

Use this appliance only as described in this manual. Any other use not recommended

by the manufacturer may cause fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS.

Before installing, servicing, or cleaning the unit, disconnect the power by turning off the circuit breakers to the

outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely

attach a prominent warning device, such as a tag, to the service panel.

This unit must be grounded.

This appliance is not suitable for tub or shower installation, and must not be installed within a minimum of 3 feet

from the tub or shower opening. See Figure A.

Do not install this appliance lower than 7 feet (2.13 m) above the floor in the ceiling. See Figure A.

WarNING

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

Continued

3 ft. min.

(0.91 m)

Bath Fan

Tub or Shower area

NOTE: This illustration is not

to scale

7 ft. min.

(2.13 m)

Figure A

43044-01 03/05/2008

Never place a switch where it can be reached from a tub or shower. Do not install this appliance in a tub or

shower enclosure.

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and standards.

When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities.

9) Do not install this product in a wall. This product is designed for installation in ceilings up to a 12/12

pitch (45 degrees). Ductwork must point upward.

10)

Ducted fans must always be vented to the outdoors. Keep ducting as short and as straight as possible.

11) Extreme caution is necessary when any is used by or near children or invalids and whenever the is

left operating and unattended.

12) To avoid motor bearing damage and noisy/unbalanced blower wheel, keep drywall spray, construction

dust, etc. off power unit.

13) Read specification label on product for further information and requirements.

14) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or fire, or damage the unit.

15)

Do not use this appliance with a dimmer switch or a fan speed controller.

16) To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control device.

17) To prevent a possible fire, do not block air intakes or exhaust in any manner.

18) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application

and be connected to a GFCI (Ground Fault Circuit Interrupter)-protected branch circuit.

43044-01 03/05/2008

95044-01-000

98141-01-000

03242-07-133

98142-01-000

97134-01-000

74508-03-133

Mounting Rails

Housing

Wiring Cover

Fan Assembly

3/8” Cable Connector

Bezel

Wiring Cover Screw

Check all the parts. If damaged, call

1-888-830-1326 for replacement.

Mounting Screws

Fan Mounting Screws

NOTE: Strain relief (not supplied) cable

connector must be installed.

Attachment Screws

96934-01-000

Strain Relief Bracket

Strain Relief Bracket Screw

65827-01-000

74508-53

Turn off the power source.

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

Before Installation

Included.

Loosen the fan mounting screws.

43044-01 03/05/2008

Loosen the wiring cover screw.

Remove the fan assembly from the housing.

Remove the wiring cover.

Choose Installation Option

For New Construction - attaching to joist, go to step A1, page 5.

For New Construction - suspended between, joists go to step B1, page 7.

For Existing Construction - accessible from above, go to step C1, page 9.

For Existing Construction - accessible only from below, go to step D1, page 12.

43044-01 03/05/2008

Section A - New Construction - attaching to joist

Drive mounting screws (supplied) into joist or framing.Position the correct depth mark at the bottom edge of the

joist based upon the the thickness of your sheetrock.

5/8

1/2

5/8

1/2

Pop out a wiring access slug.

Install the wiring and the strain relief into the wiring access

hole you made earlier.

Run the power supply wire through the strain relief, leaving

3” between the end of the wire and the strain relief. Tighten

the strain relief around the wire.

3”

43044-01 03/05/2008

Connect 6” duct and vent to the outside. Use duct tape to

secure joints. If ducting does not fit securely, an adapter

may need to be purchased.

Section B - New Construction – suspended between joists

Pop out a wiring access slug.

Slide the mounting rails into brackets. Note the orientation

of of the outer ends of the rails.

Position the correct depth mark at the bottom edge of the

joist based upon the the thickness of your sheetrock.

5/8

1/2

5/8

1/2

43044-01 03/05/2008

Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline.

1/16” bit

Insert mounting screws, leaving space between the screw

head and the joist. (Screws are supplied.) Attach the rails onto the screws.

Tighten screws. Run the power supply wire through the strain relief, leaving

3” between the end of the wire and the strain relief. Tighten

the strain relief around the wire.

3”

43044-01 03/05/2008

B10

Install the wiring and the strain relief into the wiring access

hole you made earlier.

B11

Connect 6” duct and vent to the outside. Use duct tape to

secure joints. If ducting does not fit securely, an adapter

may need to be purchased.







Remove an existing fan and check to make sure the opening

is large enough to accommodate the new fan housing. The

opening needs to be 11” x 9 5/8”.

Section C - Existing Construction – accessible from above

NO EXISTING FAN

43044-01 03/05/2008

Slide the mounting rails into brackets.

5/8

1/2

5/8

1/2

Using the depth markings on the housing, position the

bottom edge of the housing so that it will be flush with the

sheetrock.

Pop out a wiring access slug.

Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline, AS SHOWN.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Hunter Ventilateur

Hunter

Hunter Belmor Manuel d'instructions

Hunter

Hunter 28673 Mode d’emploi

Hunter

Hunter 42624-01 Manuel utilisateur

Hunter

Hunter Caribbean Breeze 54094 Manuel d'instructions

Hunter

Hunter 90400 Manuel utilisateur

Hunter

Hunter 21575 Manuel utilisateur

Hunter

Hunter Hunter Ceiling fans Manuel utilisateur

Hunter

Hunter 28528 Manuel utilisateur

Hunter

Hunter Masterson 52122 Manuel d'instructions

Hunter

Hunter 22363 Manuel utilisateur

Hunter

Hunter Altitude Manuel d'instructions

Hunter

Hunter Swanson Manuel utilisateur

Hunter

Hunter Cavera Manuel utilisateur

Hunter

Hunter Hunter Ceiling fans Manuel utilisateur

Hunter

Hunter Norway 20490 Manuel d'instructions

Hunter

Hunter Highbury 52008 Manuel d'instructions

Hunter

Hunter Milmack Manuel utilisateur

Hunter

Hunter 23562 Manuel utilisateur

Hunter

Hunter 21348 Mode d’emploi

Hunter

Hunter Hunter Ceiling fans Manuel utilisateur

Hunter

Hunter Gallery Edition Manuel utilisateur

Hunter

Hunter Castleton 55043 Guide de configuration

Hunter

Hunter Apex 59156 Manuel d'instructions

Hunter

Hunter Zayden Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage

Litex Industries

Litex Industries E-CGL52CB5C1 Manuel utilisateur

Lindab

Lindab LTDF Manuel utilisateur