Human Touch HT-120 Mode d'emploi

REMOVING THE BACKREST

1. Locate the connector box on the bottom right-hand side of the chair, use a Phillips-head screwdriver to remove the two screws that secure the connector

box cover, remove the cover, then disconnect both connectors (Fig.3).

2. Using a nail clippers, or other suitable instrument, cut and remove all zip ties that secure the two backrest connectors and cables to the bottom of the

chair, being careful not to cut the wire casing.

Tools Required: Pliers, vice grip, Phillips-head screwdriver, small hammer, nail clipper or other instrument suitable for cutting zip ties, new zip ties

NOTE: This procedure can be completed by one person, although having a second person is helpful when

installing the new backrest. SAVE ALL PARTS FOR USE DURING REASSEMBLY.

1. Remove the head pillow and backrest pad (see Use & Care manual for more information).

2. Push down on the backrest release lever, then fold the backrest forward onto the chair seat (Fig.1).

3. Power off the chair and unplug it.

GET READY

Backrest release lever

Connector box

(Left-hand side of the chair)

REPLACING THE BACKREST

HT-120/121

(Fig.1)

(Fig.2)

Connector box

(Right-hand side of the chair)

(Fig.3)

It is imperative that Human Touch® products are repaired in a manner that ensures product safety and regulatory compliance and that is fully consistent with the practices used

during the manufacturing process. Therefore, Human Touch requires that all product repairs are performed using only factory-new parts and in accordance with these repair

instructions. Failure to adhere to these instructions voids the product warranty and releases Human Touch from all liability for injury or product damage resulting from the repair.

SERVICE LEVEL: 3

Aug 22, 2010

3. Pull gently outward on the bottom of one of the side panels to remove it (Fig.4).

4. Use a needle-nosed pliers to remove the cotter pin from the side panel, then use a vice grip to pry the hinge pin loose from the side panel and remove it (Fig.5).

NOTE: When the hinge pin is removed, the two spacers that are located between the backrest and the chair base will most likely fall off Fig.6). Be sure to set

these spacers aside for use during reassembly.

5. Repeat steps 6 and 7 on the other side panel.

6. Carefully lift the backrest up and off the chair base.

Cotter pin

Hinge pin

(Fig.5)

Backrest

spacers

(Fig.6) 2

(Fig.4)

INSTALLING THE NEW BACKREST

1. Place the new backrest into position, face-down on the chair base.

2. From the outside of one of the side panels, insert the hinge pin through the hole, just until it is visible on the inside of the side panel.

3. Place the two spacers into position on the inside of the side panel, with the smaller spacer between the larger spacer and the side panel, then push the

hinge pin through both spacers (Fig.7).

4. Use your fingers to line up the bracket in the side of the backrest and the hinge pin; you will need to pull up slightly on the lower part of the backrest to

properly align the hinge pin with the bracket. (NOTE: Use your fingers to locate the circular bracket in the side of the backrest before attempting to

insert the hinge pin into the backrest. You can easily locate the hole by pushing firmly inward on the side of the backrest until you feel the metal bracket

beneath the upholstery.)

5. Insert the hinge pin as far into the bracket as possible, then use a small hammer to install it completely into the bracket.

6. Insert the cotter pin into the hinge pin, then use a needle-nosed pliers to bend the ends back.

7. Replace the side panel by aligning the plugs on the inside of the cover with the corresponding holes on the chair, then pushing the cover firmly

into place (Fig.8).

Hinge pin

Side panel

Smaller spacer

Larger spacer

Backrest

(Fig.7) (Fig.8)

8. Repeat steps 2 - 7 on the other side panel.

9. Reconnect the cables at the connector box on the bottom right-hand side of the chair (Fig.9).

10. Using a Phillips-head screwdriver, secure the connector box cover using the two screws you removed earlier.

11. Reconnect the cables at the connector box on the bottom left-hand side of the chair (Fig.10).

12. Using your fingers, secure the connector box cover.

13. Replace the zip ties you removed previously, to secure the connector boxes and cables to the bottom of the chair.

14. Reinstall the chair pads (See the Use & Care manual for instructions).

15. Plug in and power on the chair, then verify that both the massage and recline functions work.

(Fig.9) (Fig.10)

Please send any questions or comments regarding these instructions to: [email protected]

Connector box

(Right-hand side of the chair)

Cables

Connector box

(Left-hand side of the chair)

Cables

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Human Touch masseur

Human Touch

Human Touch AcuTouch 6.0 Manuel utilisateur

Human Touch

Human Touch Robotic Massage iJoy2400 Manuel utilisateur

Human Touch

Human Touch foot soother elite Manuel utilisateur

Human Touch

Human Touch ZeroG Volito Manuel utilisateur

Human Touch

Human Touch ht 125 Manuel utilisateur

Human Touch

Human Touch REFLEX SWING Pro Manuel utilisateur

Human Touch

Human Touch ZeroG 5.0 Manuel utilisateur

Human Touch

Human Touch HT-5270 Manuel utilisateur

Human Touch

Human Touch SUPER NOVO 2.0 Manuel utilisateur

Human Touch

Human Touch IJOY HT-2720 Manuel utilisateur

Human Touch

Human Touch HT-1650 Manuel utilisateur

Human Touch

Human Touch HT-100 Manuel utilisateur

Human Touch

Human Touch iJoy250 Manuel utilisateur

Human Touch

Human Touch feel better HT-5020 Manuel utilisateur

Human Touch

Human Touch ThermoStretch HT-7120 Manuel utilisateur

Human Touch

Human Touch SANA Manuel utilisateur

Human Touch

Human Touch iJoy-100 Instructions d'utilisation et de sécurité

Human Touch

Human Touch REFLEX POPUP Manuel utilisateur

Human Touch

Human Touch SUPER NOVO 2.0 Manuel utilisateur

Human Touch

Human Touch iJoy-241 Manuel utilisateur

Human Touch

Human Touch HT-Navitas Sleep Ascent Series Manuel utilisateur

Human Touch

Human Touch PC6 Manuel utilisateur

Human Touch

Human Touch ThermoStretch HT-7120 Manuel utilisateur

Human Touch

Human Touch PC-095 Manuel utilisateur

Manuels masseur populaires d'autres marques

ELEEELS

ELEEELS P2 Manuel utilisateur

Cenocco

Cenocco CC-9111 Manuel utilisateur

Panasonic

Panasonic EP790-C1 Manuel utilisateur

Adler

Adler AD 2167 Manuel utilisateur

Taurus

Taurus Wellness TW-MC-M Manuel utilisateur

Infinity

Infinity Syner-D Circadian Manuel utilisateur

Hydas

Hydas LH-095 Manuel utilisateur

AEG

AEG FM 5567 Manuel utilisateur

OBH Nordica

OBH Nordica Shiatus Tunes Manuel utilisateur

Hutech

Hutech Q9 Manuel utilisateur

Medisana

Medisana MM 825 Manuel utilisateur

SOLAC

SOLAC Therma Hydro Manuel utilisateur

Invacare

Invacare Texas Manuel utilisateur

Casada

Casada Bismarck II Manuel utilisateur

Fujiiryoki

Fujiiryoki Cyber-Relax EC-1700 Manuel utilisateur

Medisana

Medisana HM 886 Manuel utilisateur

HoMedics

HoMedics BA-C200 Manuel utilisateur

Repose

Repose Lynton Manuel utilisateur