Hubsan HT006 Manuel utilisateur
®
《HT006 User Manual 》
HT006 GPS WATCH
Version 2.0
Connect the GPS watch with the provided Micro USB charging
cable to a 5V adapter or PC terminal to charge. When charging, the
LED right above the Micro USB port on the unit stays solidly lit;
when charging is complete, the LED will extinguish itself. In the
latter case, please disconnect the watch and cable. In general,
approximate charging time is 40 minutes.
Charging the HT006
Product Description
The Hubsan HT006 is a remote-control watch equipped with GPS.
It may be paired with a Hubsan aircraft for flight and is suitable for
any Hubsan equipped with a 2.4G flight control signal and GPS.
Recommended flight distance is 60 meters.
Step 1
Place the aircraft on a flat and open floor/surface, with the head facing
away from the user.
Step 2
Pair the watch with the aircraft.
The watch must be paired with the aircraft for the units to operate
properly.
The pairing steps are as follows:
1. Please begin with the watch powered off. Press the power and
camera buttons to enter pairing mode. Notice all 5 LEDs on the unit
flash simultaneously.
Basic Flight Operation
Calibration steps:
Make sure the aircraft is resting on a flat and level surface. At this
point, its 4 LEDs will transition from flashing simultaneously to
flashing clockwise. Start compass calibration.
●If after initialization, the aircraft and watch have not paired for
some time, please restart both units.
Step 3
Compass calibration
The compass must be calibrated every time the aircraft is powered
on. The compass is susceptible to interference by other electronic
equipment, magnetic interference and metal, which can lead to
erratic behavior and loss of control. Regular calibration helps keep
the compass and its readings accurate.
2. Connect the aircraft to its battery; make sure the two are very
close to each other. Allow the watch and aircraft to pair; the watch
LEDs will stop flashing to indicate a successful pairing.
3. After the pairing is successful, aircraft and watch LEDs should be
solidly lit. While in GPS mode, the aircraft and watch LEDs flash
slowly.
●Do not calibrate the compass in areas with strong magnetic
interference, magnetic objects or structures, in areas with
underground wiring, large pieces of metal or large metal
structures.
●Do not carry ferromagnetic materials while calibrating the
compass, such as keys, cell phones, etc.
。
Horizontal calibration
1) Horizontal calibration：
Slowly rotate the aircraft on the horizontal
plane. The LEDs should be flashing
clockwise; proceed to step 2 when the
LEDs start flashing in vertical pairs,
alternately.
vertical calibration
2) Vertical calibration：
Point the head of the aircraft downwards
and rotate the aircraft in place until the
LEDs cease to flash and stay solidly lit.
Manual calibrations:
Horizontal/Gyro calibration:
Simultaneously long press the Camera and Orbit keys for 3 seconds
to calibrate the aircraft gyro sensor. Make sure that the aircraft is on
a smooth and level surface.
Compass calibration (manual):
Simultaneously long press the Video and Orbit keys for 3 seconds to
manually initiate a compass calibration.
Allow the watch and aircraft GPS signals to stabilize; the GPS LED
indicators for both the watch and aircraft should be solidly lit. At this
point, users may arm the motors for flight.
Step 4
Note: Refer to the User Manuals for both the HT006 and the aircraft
in use for instructions on how to use Follow Me, Orbit and other
functions.
Step 5
To arm the motors for flight, first long press the arming key and then
the Auto Takeoff key. The watch will vibrate once; the aircraft will
takeoff and hover at a height of around 3m. The Auto Takeoff key
becomes the Return to Home key when the aircraft is in flight.
Auto Takeoff
Step 7
When the motors have disarmed themselves/stopped, power off the
aircraft and watch.
Step 6
To end the flight, choose a flat open space and press the Return to
Home key. The aircraft will return to where the GPS watch is located
and automatically land.
Return to Home
The Failsafe: The aircraft will Return to Home automatically under
the following circumstances.
(1) When the aircraft is too far away from the watch or the flight
control signal between the drone and watch is lost, the aircraft will
initiate a Return to Home.
(2) If the watch shuts off due to low voltage, or suffers damage that
causes it to lose connection with the aircraft, the aircraft will initiate
a Return to Home. If the aircraft re-connects with the watch during
the Return to Home, users may continue to use the watch to control
the aircraft.
HT006 GPS Watch Components and Functions
Aircraft GPS status LED
Right
Backward
Left
Forward
HT006 GPS status LED Video recording status LED
Aircraft Power status LED
HT006 Power status LED
Video
Orbit Mode
Power (On/Off)
Auto Takeoff
/Return to Home
Height adjustment
dial/Arm/Disarm
Heading adjustment
dial/Follow Me Mode
Photo
Reset button
Micro USB port
Charging status LED
Arming the Aircraft Motors
Method 1: Long press the Height Adjustment Dial for 1.5 seconds to
arm and start up the aircraft motors.
2.Arming/Disarming motors
When the dial is turned completely upwards (the dial will stop), the
aircraft will rise. When the dial is turned completely downwards (the
dial will stop), the aircraft will descend. When the dial is in a neutral
position, the aircraft will hover without rising or falling.
1.Height Adjustment Dial
●When the dial is in descent position for more than 4
seconds, aircraft descent speed will increase.
●Make sure that the GPS status LEDs for both the aircraft
and watch are solidly lit (the GPS signals are stable and
strong) before arming the motors. If they are not, the motors
will not arm.
●The aircraft is programmed to only allow a Method 2
disarm in the case of a serious aircraft failure. Disarming the
motors in mid-flight will most likely cause the aircraft to
crash.
After the motors are armed and spinning, there are two ways of
stopping/disarming them.
Method 1:
When the aircraft has made a full landing, turn the Height Adjustment
Dial to its most downward position and hold it there. The motors will
stop after 5 seconds.
Method 2:
Turn both the Height Adjustment Dial and the Heading Adjustment
Dial completely downwards (at the same time). Release both dials
when the motors stop.
Method 1 Method 2
Table des matières
