HTW HTW-XK60 Manuel utilisateur
08/&3h4."/6"-
:,5('&21752//(5
HTW-XK60
7KDQNVIRUFKRRVVLQJRXUSURGXFW
3OHDVHUHDGFDUHIXOO\WKLVPDQXDO
EHIRUHXVLQJWKHSURGXFW
E/(-*4)
User Notice
Please carefully read this manual before installation and use of this
product.Thanks for choosing +7: duct type air conditioners. Please read this manual
carefully before operating this product and keep it properly for future reference. In
addition, please take notice of the symbols below.
WARNING!
This mark indicates procedures which, if improperly performed, might lead to
the death or serious injury of the user.
CAUTION!
This mark indicates procedures which, if improperly performed, might possibly
result in personal harm to the user, or damage to property.
CAUTION!
Do not install the wired controller in the damp place or under direct sunlight.
Do not beat,
toss, or frequently assemble/disassemble the wired controller.
Do not operate the wired controller with wed hands and never let any liquid flow into it.
Do not install or remove the wired controller by yourself. If necessary, please contact the after
-sa
les
serviceman.
This wired controller is applicable to various kinds of air conditioners, while some specific functions
unavailable to the duct type air conditioners will not be covered in this manual.
Before operating the air conditioner, please read this manual carefully and keep it properly for future
reference.
Contents
1 Introduction to the Wired Controller......................................... 1
1.1 Appearance and LCD Icons .......................................................1
1.2 Introduction to the LCD Icons.....................................................2
2 Press Buttons ..........................................................................3
2.1 Buttons ......................................................................................3
2.2 Instruction to the Function of Press Buttons...............................3
3 OPERATION INSTRUCTION ..................................................4
3.1 On/off.........................................................................................4
3.2 Mode Setting..............................................................................5
3.3 Temperature Setting...................................................................5
3.4 Fan Speed Setting .....................................................................6
3.5 Right and Left Swing..................................................................6
3.6 Up and Down Swing ..................................................................7
3.7 Timer Setting..............................................................................8
3.8 Air Exchange Setting..................................................................9
3.9 Sleep Setting ........................................................................... 11
3.10 Health Setting ........................................................................13
3.11 I-Demand Setting ...................................................................13
3.12 Vacation Setting.....................................................................14
3.13 Turbo Function Setting...........................................................15
3.14 SAVE Function Setting...........................................................16
3.15 E-HEATER Setting.................................................................18
3.16 Blow Function Setting ............................................................19
3.17 Filter Setting...........................................................................19
3.18 Quiet Function Setting............................................................22
3.19 Ultra-Dry Setting ....................................................................23
3.20 Other Functions .....................................................................23
4 Installation of the Wired Controller......................................... 25
4.1 Standard Parts.........................................................................25
4.2 Installation Location and Installation Requirements..................26
4.3 How to Install the Wired Controller...........................................26
4.4 How to Remove the Wired Controller.......................................27
5 Error Display.......................................................................... 27
Wired Controler +7:XK60
1
1 Introduction to the Wired Controller
Fig.1 Appearance of the Wired Controller
1.1 Appearance and LCD Icons
Fig.2 Appearance of the LCD
Wired Controler +7:XK60
2
1.2 Introduction to the LCD Icons
Table 1
No.
Icons
Introduction
1
Left and right swing function
2
Up and down swing function
3
Air exchange function
4
Sleep function
5
Auto mode
6
COOL mode
7
DRY mode
8
FAN mode
9
HEAT mode
10
Health function
11
I-
Demand function
12
Vacation function
13
Status display of master and slave wired controller
14
Shield function
The button operation, temperature setting, "On/Off" operation, "Mode"
setting, and "Save" setting are disabled.
15
Fan speed
16
Memory function
The unit will resume the original setting state after power recovery.
17
Turbo function
18
Energy
-saving function
19
Ambient/setting temperature
Wired Controler +7:XK60
3
20
Electric heater
21
Blow function
22
Defrosting function
23
Filter
cleaning
24
Ti
mer Setting
25
Keycard control / Detected status sensed by human body
26
Quiet function
27
Lock function
2 Press Buttons
2.1 Buttons
Fig.3 Press Buttons
2.2 Instruction to the Function of Press Buttons
Table 2
No.
Press Buttons
Function Introduction
1
Enter/Cancel
Function selection and canceling;
Press it for 5s to enquiry the outdoor and indoor ambient temperature.
2▲
Running temperature setting of indoor unit, range :16~30°C
Timer setting, range:0.5
-24hr
Air function se
tting
Save setting
Clean setting
6▼
Wired Controler +7:XK60
4
3Fan
Select fan speed from high, mid-high, middle, mid-low, low and auto
levels.
4
Mode
Selection of the COOL, HEAT, FAN, Auto or DRY mode.
5 Function
Switchover among these functions of
SWING/AIR/SLEEP/HEALTH/I
-D
EMAND/VACATION/TURBO/SAVE/E-H
EATER/BLOW/QUIET
7
Timer
Timer setting
8
On/Off
Turn on/off indoor unit
4 mode
and 2 ▲
Memory
Press Mode and ▲at the same time for 5s under the OFF state of the unit
to activate/deactivate memory function (If memory is set, indoor unit will
resume original setting state after power recovery. If not, indoor unit is
defaulted to be OFF after power recovery. Memory function is defaulted to
be ON)
2 ▲
and 6 ▼
Lock
Under the ON state of the unit without any malfunction or under the OFF
state of the unit, press ▲and ▼buttons at the same time for 5s to go to
the lock state. In this case, any other buttons won’t respond the press.
Repress ▲and ▼again for 5s to quit the lock state.
4 mode
and 6 ▼
°F/°C
Under the OFF state of the unit, press the Mode and ▼at the same time
for 5s to switch the temperature scale between Celsius and Fahrenheit.
3 OPERATION INSTRUCTION
3.1 On/off
Press the On/Off button to turn on or off the unit.
Notes:
ķThe state shown in Fig.4 indicates the OFF state of the unit after energization.
ĸThe state shown in Fig.5 indicates the ON state of the unit after energization.
Fig.4 OFF State of the Unit Fig.5 ON State of the Unit
Wired Controler +7:XK60
5
3.2 Mode Setting
Under the ON state of the unit, press the Mode button to switch the operation
modes as the sequence shown in Fig.6:
Fig.6
3.3 Temperature Setting
Press ▲or ▼button to increase or decrease setting temperature under on-state of
the unit. If press either of them continuously, temperature will be increased or
decreased by 1°C every 0.5s.
In Cooling, Dry, Fan and Heating mode, temperature setting range is 16°C~30°C.
In Auto mode, the setting temperature is un-adjustable.
As shown in Fig.7:
Fig.7 Temperature Setting
Wired Controler +7:XK60
6
3.4 Fan Speed Setting
Press Fan button, fan speed of indoor unit will change as the sequence shown in
Fig.8:
Fig.8 Fan Speed Setting
3.5 Right and Left Swing
Under the ON state of unit, press the Function button to select the “Right and Left
Swing” function option and then press the Enter/Cancel button to activate it.
When the Swing function is activated, press the Function button to select the
"Right and Left Swing" function option and then press the Enter/Cancel button to
deactivate it.
Right and Left Swing function setting is as shown in Fig.9.
Table des matières
Autres manuels HTW Contrôleurs
