HP Integrity BL860c Manuel utilisateur

HP Array Configuration Utility Command

Line Interface for Integrity Linux Environments

Support Notes

Version 8.40

HP Part Number: 5992-3868

Published: March 2010

Edition: 5

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial

Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under

vendor's standard commercial license. The information contained herein is subject to change without notice. The only warranties for HP products

and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as

constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. UNIX is a registered

trademark of The Open Group.

Table of Contents

HP ACU-CLI Overview..........................................................................................................................5

Supported Configurations......................................................................................................................5

Installation and Usage Instructions........................................................................................................5

Installing HP ACU-CLI:....................................................................................................................5

Using HP ACU-CLI:..........................................................................................................................5

Exiting the HP ACU-CLI:..................................................................................................................5

Important Usage Notes.....................................................................................................................5

System Requirements and Dependencies...............................................................................................6

Known Issues..........................................................................................................................................6

Problems Resolved..................................................................................................................................7

Support...................................................................................................................................................9

Feedback.................................................................................................................................................9

Table of Contents 3

HP ACU-CLI Overview

The HP Array Configuration Utility Command Line Interface (HP ACU-CLI) is a

command-line-based disk configuration tool that can be used to configure and manage Smart

Array Controllers and RAID Array Controllers in Integrity Linux environments.

HP ACU-CLI is available as a part of the HP Insight Foundation Suite for Integrity with Linux

and can be obtained from the Linux on HP Integrity Servers web site:

http://www.hp.com/go/integritylinux

This document provides information about the of HP Array Configuration Utility Command

Line Interface (HP ACU-CLI) version 8.40 release.

Supported Configurations

HP ACU-CLI provides support for a number of configurations. See the Linux section of the HP

9000 and HP Integrity Server-Storage Support Matrices web site for the latest information about

supported configurations:

http://www.hp.com/products1/serverconnectivity/support_matrices.html#linux

Installation and Usage Instructions

Installing HP ACU-CLI:

HP ACU-CLI is distributed using Red Hat Package Manager (RPM) packages.

1. If there is an older version of HP ACU-CLI installed on the system, you must use rpm -e

hpacucli to remove it first.

2. To install the HP ACU-CLI application, enter:

rpm -i <filename>

TIP: For additional details regarding RPM, use the man rpm command.

The software resides in /opt/compaq/hpacucli and the executable name is hpacucli which

is located in /usr/sbin.

Using HP ACU-CLI:

You must run hpacucli as root.

1. Ensure that /usr/sbin is root's path.

2. To start the HP ACU-CLI application, enter:

hpacucli

TIP: For more options, use the hpacucli help command.

Exiting the HP ACU-CLI:

To exit the HP ACU-CLI, at the CLI command console, enter:

exit

Important Usage Notes

• The CCISS and CPQARRAY drivers support up to 16 logical drives per controller. After

creating or deleting logical drives with HP ACU-CLI, under some special circumstances,

HP ACU-CLI Overview 5

the device name mapping might change after you first reboot the system. Also, after

rebooting, Linux might see logical drives that were previously not visible. This name mapping

problem is common to all SCSI devices on Linux.

• Do not insert or remove a controller driver module when hpacucli is running.

• Stop the HP Storage Agents when deleting logical drives since HP Storage Agents keep all

logical drives open.

• If all physical drives on a controller fail or are removed, software keys will not be saved to

the controller.

• HP ACU-CLI may appear unresponsive during heavy array controller I/O conditions, such

as during a partition format or a logical drive rebuild.

• HP ACU-CLI will not disallow the deletion of logical drives on fibre channel controllers

that have mounted partitions.

System Requirements and Dependencies

HP ACU-CLI requires HP Management Base (hpmgmtbase) to be installed on the system. HP

Management Base is a package of tools, scripts, and binaries that ensure proper system

manageability functionality by providing access to the management processor through the Open

IPMI driver.

HP management base packages are distribution-specific and are found in the HP Insight

Foundation Suite for Integrity with Linux product. Download this product from the Open Source

and Linux from HP website:

http://www.hp.com/go/integritylinuxessentials.

HP recommends using the most updated versions of HP supported device drivers for the Smart

Array controllers and Fibre Channel host bus adapters.

Known Issues

This section contains known issues with the HP ACU-CLI product, which undergoes rigorous

testing before each release. From HP test activities to date, the following items have been

uncovered that you should keep in mind.

•Error "[Not FC Transport, discarding (2)]" appears on the sles10sp3/emulex

card.

When launching hpacucli, this error pops up, either hp-fc-enablement lib 1.2-1

or 1.2-2

Workaround: None at this time. This error will not affect functionality.

•SSP presented information is lost after SSP state toggles.

SSP-related information such as unmask or mask is lost after SSP state is changed from off

to on state.

Workaround: None at this time.

•HP ACU-CLI compatibility issue with RHEL5U1.

On HP Integrity servers running RHEL5U1, HP ACU-CLI causes kernel panics when issuing

various hpacucli operations on a SmartArray controller configured with more than one

logical drive. For example, issuing either the show config or ctrl all show status

commands result in a kernel panic. Multiple installed SmartArray controllers, each with a

single logical drive, are not affected. This issue is specific to the RHEL5U1 release and does

not occur with RHEL5.

NOTE: To avoid creating this adverse condition, the HP Integrity Essentials Foundation

Pack for Linux installer will not install the HP ACU-CLI (hpacucli) product on these

servers and this option is not displayed in the product installation menu. Further, if

hpacucli is detected on the system, it is uninstalled by the installer.

Workaround: If multiple logical drives are required on a given SmartArray controller, use

the ORCA utility at the EFI shell to configure them. Do not use hpacucli to configure these

storage devices. Alternatively, you can upgrade the OS to RHEL5U2.

THIS ISSUE WAS FIXED IN FOR THE RHEL5U2 RELEASE.

•On a CoreIO P400 with an OS installed on it, the deleting array operation acts abnormally.

On HP Integrity servers, the operation to delete an array should be successful with or without

an OS installed. However, when the delete array operation is performed for an array on

CoreIO P400 controllers, the operation fails and the following error message is displayed

"Error: Could not delete array *".

Workaround: Deleting an array on CoreIO P600 controllers with an OS installed on operates

as expected.

•hpacuscripting return code is not "0".

On HP Integrity servers running RHEL5.4, RHEL4.8, SLES10SP3, or SLES11SP1, run the

command "$hpacuscripting -i acuinput.ini -internal" on SmartArray

controllers or run "$hpacuscripting -i acuinput.ini -external" on FibreChannel

controllers to write configuration to the hardware, the return code is not "0", but "11". An

"error.ini" file will not be created.

Workaround: This error does not affect functionality.

•hpacucli acts abnormal on rhel5.4Xen with Qlogic card and MSA1000/1500 storage.

On RHEL5.4xen, with hpacucli8.40+hp-fc-enablement-1.1-13 installed, use

hpacucli for show, create, or delete operations on MSA1000/1500 connected to

AB379A/AB379B (Qlogic card).

Workaround: On RHEL5.4, the hpacucli show/create/delete functions act normally.

Problems Resolved

The following issues have been resolved in previous releases of the HP ACU-CLI.

•HP ACUCLI 8.25 installation encounter dependence issue on SLES10 and SLES11.

Installing ACUCLI8.25 on SLES10 and SLES11 will issue a "compat libstdc:: 296"

dependence issue.

THIS ISSUE WAS FIXED IN THE 8.28 RELEASE.

Workaround: For a SLES10 installation, skip the dependency check before the ACUCLI 8.25

installation. Use the command rpm -ivh hpacucli-8.25-5.ia64.rpm nodeps.

Workaround: For a SLES11 installation, install the file compat 2008.10.27

1.9.ia64.rpm before the ACUCLI 8.25 installation. Next, execute the command rpm

-ivh hpacucli 8.25-5.ia64.rpm nodeps. The file

compat-2008.10.27-1.9.ia64.rpm is included in the HPIEFPL 2.5 CD.

•Migration of logical volume using an unsupported stripe size does not work.

THIS ISSUE WAS FIXED IN THE 8.28 RELEASE.

Attempts to migrate the stripe size of a logical volume to unsupported sizes results in no

error message.

Workaround: You should only migrate existing striping to supported sizes.

Problems Resolved 7

•Using HP ACU-CLI on HP Integrity cellular servers is slow.

THIS ISSUE WAS FIXED IN THE 8.28 RELEASE.

Using HP ACU-CLI on HP Integrity cellular servers (for example, an rx8640 server is

cell-based) is extremely slow. Operations within hpacucli, such as “ctrl all show”

status can take several minutes to finish. This issue does not occur on non-cellular HP

Integrity servers.

Workaround: Ensure that you allow an adequate amount of time, commensurate with the

storage size of your server, for the operation to complete. Do not attempt to execute additional

commands until the hpacucli operation has finished.

•Rebuild issue when Smart Array 6402 controller is installed in an rx4640 connected to

internal volumes.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

ACU-CLI should perform a rescan of the SCSI bus as a result of running "rescan" or "pd

show all" commands. This in turn should initiate a rebuild of an array after replacement

of a failed drive. The rebuild does not take place as a result of running these commands with

the released version.

Workaround: You can initiate a rescan by exiting and then rerunning HP ACU-CLI, or by

rebooting the system.

•CCISS interface/driver reports inaccurate information on logical volumes.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

Under some circumstances, the CCISS driver can show devices that have not actually been

created. When this happens, a number of different devices are reported to the OS, but there

is actually only one logical volume.

Workaround: You should reboot the system after creating a new logical volume.

•Using HP ACU-CLI from two clients at the same time results in warning messages upon

exiting from one of the clients.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

Workaround: Use only one instance of HP ACU-CLI at a time.

•Unexpected LED behavior under some circumstances.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

All LEDs will go “off” if the customer performs the following steps:

ACUCLI> modify led=on

ACUCLI> pd xxx modify led=off

Workaround: There is no workaround.

•Logical volume status abnormal after powering down OS on some cell-based systems.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

After a cell-based system is powered off using the Linux command “poweroff” or “halt”,

the status of logical volumes that have been previously created may show as FAILED. Also

you may be unable to delete the logical volume in question.

Workaround:You must use the management processor to power off the HW partition, then

power on again.

•Logical volume created on rx2620 does not appear on rx7620.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

In some circumstances, logical volumes created on one system do not appear on another

system, even after a system reset.

Workaround: You must totally power off the HW partition and then power on in order to

see the logical volume.

•Cannot query the logical volume size using the “create” command.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

The logical volume size cannot be successfully queried using the “create” command.

Workaround: None at this time.

•OS fails to recognize configuration changes.

THIS ISSUE WAS FIXED IN THE 7.65 RELEASE.

When existing volumes are modified or deleted, or when new volumes are created using

HP ACU-CLI, the operating system will not always be aware of the changes unless the

system is rebooted.

Workaround: You must reboot the system after making changes to existing volumes.

•ACU-CLI cannot delete the last logical disk.

THIS ISSUE WAS FIXED IN hpacucli8.40+hp-fc-enablement-1.1-13.

ACU-CLI cannot delete the last logical disk that connects to the Qlogic Fibre Channel card.

This issue only happens on RHEL5.3, SLES11, RHEL5.4 and SLES10SP3.

Workaround: The last disk can be deleted on RHEL4 and SLES10SP2

•Mount point displays as "None" after mounting the LD into the OS.

THIS ISSUE WAS FIXED IN hpacucli8.40+hp-fc-enablement-1.1-13.

After mounting your logical drive into the operating system and executing the command

"ld <your id number> show", the system displays the message [None] as the status for

the mount points.

Workaround: Execute the command mount from the command line to display the correct

mount points for your LD.

•hpacucli acts abnormal with the qlogic card and the hp-fc-enablement rpm.

THIS ISSUE WAS FIXED IN hpacucli8.40+hp-fc-enablement-1.1-13.

hpacucli fails to delete the last array due to an issue with the qlogic driver and

hp-fc-enablement lib. This issue occurs on RHEL5.3, RHEL5.4, SLES10SP3, and SLES11.

Workaround: This issue fix requires both the qlogic driver and the hp-fc-enablement

lib fix. The target operating systems for the qlogic driver fix are RHEL5.5 and SLES10SP3.

The lib fix issue will be fixed with version 1.1-9. For the RHEL5.4 and SLES10SP3 operating

systems the fix version will be 1.2-1+.

Support

Support for HP ACU-CLI or Smart Array controllers can be obtained at the HP Customer Care

web site at:

http://support.hp.com

Feedback

For feedback or suggestions regarding HP ACU-CLI, e-mail your comments to:

[email protected]

Support 9

Autres manuels pour Integrity BL860c

Table des matières

Autres manuels HP Logiciel

HP ProLiant SL170s - G6 Server Manuel utilisateur

HP 8000 - Elite Convertible Minitower PC Manuel utilisateur

HP MultiSeat ms6000 Manuel utilisateur

HP HP-UX 11i v3 Manuel de service

HP BB118BV - StorageWorks Data Protector Express... Instructions d'installation et d'utilisation

HP Compaq dc7900 Business PC Manuel utilisateur

HP BL30p - ProLiant - 1 GB RAM Manuel utilisateur

HP Data Protector A.06.11 Guide de configuration rapide

HP Xw460c - ProLiant - Blade Workstation Manuel utilisateur

HP D5970A - NetServer - LCII Manuel utilisateur

HP HPE XP P9500 Mode d’emploi

HP cc2300 Manuel utilisateur

HP StorageWorks P4000 Series Manuel utilisateur

HP HP NonStop Data Transformation Engine FTP... Manuel utilisateur

HP T5700 - compaq thin client Manuel utilisateur

HP HPE XP P9500 Manuel utilisateur

HP Vectra VL800 Manuel utilisateur

HP StorageWorks 2/16 - SAN Switch Manuel utilisateur

HP N1200 - StorageWorks Network Storage Router Guide d'installation

HP Media Center m1000 - Desktop PC Guide de démarrage rapide

HP T5135 - Compaq Thin Client Manuel utilisateur

HP ProLiant StorageWorks NAS 2000s Manuel utilisateur

HP C7791C - DesignJet 130 Color Inkjet Printer Guide de configuration

HP HPE XP P9500 Manuel utilisateur

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur

Novell

Novell SP2 - S Mode d’emploi