HP ProLiant DL785 Manuel utilisateur
1
Processor Option Installation Instructions
for HP ProLiant DL785 Servers
Overview
This document provides the procedure for installing a processor and heatsink.
Kit contents
Processor memory cell assembly (four)
Processor with installation tool (four)
Heatsink (four)
DIMM filler (12)
This document
SW1 instructions for quad-core 3.1 GHz or greater and six-
core processors
CAUTION: All supported AMD Opteron quad-core processors 3.1 GHz or greater and all
supported AMD Opteron six-core processors require the system maintenance switch,
located on the I/O backplane, (SW1) position 5 to be in the On position.
CAUTION: HP recommends updating to the latest version of firmware. Earlier firmware
versions might not validate the required switch setting for these processors.
NOTE: Six-core AMD Opteron Processors might show a 1 MB reduction in available L3
cache when performance enhancing HT Assist is enabled because HT Assist requires 1MB
of L3 cache per CPU to operate.
Installing a processor
The server supports a four- or eight-processor configuration.
CAUTION: The cell filler is required in cells 3 - 6 in a four-processor configuration.
CAUTION: To prevent damage to electrical components, properly ground the server before
beginning any installation procedure. Improper grounding can cause electrostatic
discharge.
CAUTION: To avoid damage to the processor and system board, only authorized
personnel should attempt to replace or install the processor in this server.
CAUTION: To prevent possible server malfunction and damage to the equipment,
multiprocessor configurations must contain processors with the same part number.
2
CAUTION: Always install the processors into the processor memory cell supplied in the kit.
Failure to do so might result in processor incompatibility.
CAUTION: To help avoid damage to the processor and system board, do not install the
processor without using the processor installation tool.
To install a processor:
1. Locate and download the latest ROM version from the HP website
(http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-
002&h_lang=en&h_cc=us&h_product=241435&h_client=S-A-R163-
1&h_page=hpcom&lang=en&cc=us). Follow the instruction on the website to update the
system ROM.
2. Power down the server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal
system components to cool before touching them.
CAUTION: When working with the cell filler or processor memory cell always place the
component on a flat, level, antistatic surface.
3. Remove the cell filler. For instructions on removing the cell filler, see the label on the access
panel or the server maintenance and service guide on the Documentation CD.
4. Remove the airflow baffle from the processor memory cell.
a. Press the two airflow baffle release tabs.
b. Pivot the airflow baffle up and remove the airflow baffle.
5. Open the heatsink retaining bracket.
.
!
3
CAUTION: The pins on the processor socket are very fragile. Any damage to them may
require replacing the processor memory cell.
6. Remove the processor socket protective cover. Retain the cover for future use.
CAUTION: Failure to completely open the processor locking lever prevents the processor
from seating during installation, leading to hardware damage.
7. Open the processor retaining latch and the processor socket retaining bracket.
IMPORTANT: Be sure the processor remains inside the processor installation tool.
4
8. If the processor has separated from the installation tool, carefully re-insert the processor in
the tool.
9. Align the processor installation tool with the socket and install the processor.
CAUTION: The processor is designed to fit one way into the socket. Use the alignment
guides on the processor and socket to properly align the processor with the socket.
10. Press down firmly until the processor installation tool clicks and separates from the
processor, then remove the processor installation tool.
5
11. Close the processor retaining latch and the processor socket retaining bracket.
12. Remove the heatsink cover.
6
CAUTION: After the cover is removed, do not touch the thermal interface media.
13. Install the heatsink.
14. Close the heatsink retaining bracket.
15. Install DIMMs and DIMM fillers.
16. Replace the processor memory airflow baffle.
17. Install the processor memory cell into the server.
18. Repeat steps 4 - 17 for all four processors.
19. Power up the server.
20. The installation is complete.
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP
products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Part Number AH233-9010C
September 2009 (Third Edition) *AH233-9010C*
Autres manuels pour ProLiant DL785
2
Table des matières
Autres manuels HP Serveur
HP
HP NetServer LH 3r Manuel utilisateur
HP
HP Integrity rx2600 Mode d’emploi
HP
HP Officejet LH 6000 Manuel utilisateur
HP
HP Sa3110 - VPN Server Appliance Manuel utilisateur
HP
HP ProLiant SL250s Gen8 Manuel utilisateur
HP
HP Integrity rx1620 Guide de référence rapide
HP
HP st5742 - Streaming Client Manuel utilisateur
HP
HP 9000 rp4410 Manuel utilisateur
HP
HP DL100 - ProLiant G2 320GB File Print... Manuel utilisateur
HP
HP HP DL360 G7 Manuel
HP
HP D5970A - NetServer - LCII Manuel utilisateur
HP
HP DL320 - ProLiant - G3 Fiche technique
HP
HP ProCurve 6120G/XG Mode d’emploi
HP
HP ProLiant DL360e Manuel utilisateur
HP
HP ProLiant ML570 Generation 2 Manuel
HP
HP DL385 - ProLiant - G5 Instructions d'utilisation
HP
HP ZCentral 4R Manuel utilisateur
HP
HP Gt7725 - Compaq Thin Client Manuel utilisateur
HP
HP 124708-001 - ProLiant Cluster - 1850 Manuel utilisateur
HP
HP Integrity rx8640 Instructions d'utilisation
