HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manuel utilisateur

HP Server

Novell NetWare Installation Guide

Including 6.5

August 25, 2003

Objective

The intent of this document is to provide you with key information required for

completing the installation of NetWare on an HP Server (HP Server series or HP

Netserver series). Installation requires familiarity with both DOS and NetWare. Please

refer to Novell's NetWare Installation Guide for detailed step-by-step instructions.

This document only details how to create a DOS partition and install Network, SCSI, and

Disk Array drivers.

Table of Content

Section 1. Novell NetWare Installation Overview

Section 2. Automated Installation via the HP NetServer Navigator CD

Section 3. Creating the Drivers Diskette and Installing the IDE CD-ROM Drivers

Creating the Drivers Diskette

Installing the IDE Drive with FDATACD. SYS and MSCDEX.EXE

Section 4. Installing NetWare on the HP NetServer

NetWare 4.2 Installation

NetWare 5.1 or NetWare Small Business Suite 5/5.1 Installation

NetWare 6.0 Installation

NetWare 6.5 Installation

Section 5. General NetWare Installation Tips

Tip #1. Using the REGISTER MEMORY Command to allow NetWare 4.xx to Use

All System Memory

Tip #2. Installing NetWare 6.5 on a 4GB hard disk drive

Section 6. On-Line Information and Software Sources

Section 1. Novell NetWare Installation Overview

Installing NetWare on your network server requires two major steps:

Step 1: Preparing the bootable devices (creating a DOS partition, formatting the partition,

installing DOS, and connect the system to a CD-ROM drive.)

Step 2: Install NetWare and the appropriate HP NetServer mass-storage drivers.

Section 2. Automated Installation via the HP NetServer

Navigator CD

An Automated Installation utility is available on your HP NetServer Navigator CD

provided with your HP NetServer that will guide you through the Novell NetWare

installation. This utility will automatically create a DOS partition, format the partition,

install DOS, connect the NetServer to the CD-ROM drive, start the NetWare installation

process and install the appropriate NetServer drivers. To use this utility, first boot your

HP NetServer using the Navigator CD. Once at the NetServer Navigator Main Menu,

select the Configure the Server option. From the NetServer Navigator Mode Selection

for Configuring the Server menu select Guided Setup. Follow the on-screen

instructions to configure your system and install Novell NetWare.

Section 3. Creating the Drivers Diskette and Installing

the IDE CD-ROM Driver

NOTE: Installing NetWare without using the Automated NOS Installation feature

of the HP NetServer Navigator CD requires familiarity with DOS as well as

NetWare. If you are not familiar with these operation systems, please use the

Automated NOS Installation via HP NetServer Navigator CD.

Creating Drivers Diskette

Requirements

• HP NetServer Navigator CD-ROM

• Blank formatted diskettes

To create a DOS/NetWare drivers diskette using the HP NetServer Navigator CD:

1. Boot your HP NetServer using the Navigator CD.

2. When prompted, select the desired operating system. Once the desired operating

system is highlighted select continue.

3. Once at the NetServer Navigator Main Menu, verify information in top right corner

of the screen, and then select Diskette Library.

4. Select the desired driver. Once the desired driver is highlighted, insert a blank

formatted 1.44 MB floppy diskette into the floppy drive and select Create

Diskette(s). (Manual installation requires NOS Drivers diskette).

5. Repeat step 4 until all desired driver diskettes are created.

6. Select the Exit icon located in the bottom left hand corner of the screen after all

driver diskettes have been created.

Installing the IDE CD-ROM Drive with FDATACD.SYS and

MSCDEX.EXE

To install Netware 4.2, you must first install a CD-ROM drive and driver in the DOS

environment by using the driver diskettes you created using the HP NetServer Navigator

CD.

NOTE: DOS CD-ROM drivers are available on the NOS Drivers Diskette in the

\Cdromdrv\IDEDOS directory.

1. Boot your HP NetServer using an MS DOS bootable utility diskette.

2. Use the fdisk utility to create a 250 MB primary DOS partition on the primary

drive(C:). Remember to set the partition to active.

3. Use the format utility to format 250 MB partition.

4. Install DOS. (For detail instruction, see the instructions in the NetWare

documentation.)

NOTE: If applicable, make sure to remark the DOS=HIGH and the

DEVICE=C:\DOS\HIMEM.SYS lines in the CONFIG.SYS file by inserting the

command REM at the beginning of each line (i.e., REM DOS=HIGH). Otherwise

NetWare may not function properly.

5. Insert the NOS Drivers Diskette created from the Navigator CD into the 1.44 MB

floppy drive (A:).

6. Create a subdirectory on drive Cby entering the command:

MD directoryname

where directoryname is a valid name for a directory (for example: doscdrom).

7. Copy all DOS CDROM drivers from drive Ato this subdirectory, by entering the

command:

Copy A:\CDROMDRV\IDEDOS\*.* C:\directoryname

8. Use the edit utility to add the following lines to your CONFIG.SYS file:

DEVICE=C:\directoryname\FDATACD.SYS /D:driver1

Where directoryname is the path to the directory containing the FDATACD.SYS

driver, and driver1 specifies the driver signature name of the first CD-ROM device

driver. The driver signature name must have fewer than eight characters, for example:

DEVICE=C:\DOSCDROM\FDATACD.SYS /D:HPCD000

NOTE: The MSCDEX driver is included with MS-DOS/Windows version 6.0 or

later. The MSCDEX driver also supports a driver signature parameter (for

example, /D:driver1). The name used for this parameter must match the name

used for the FDATACD.SYS driver signature parameter.

9. Use the DOS edit utility to add the following line to your AUTOEXEC.BAT file:

C:\DOS\MSCDEX /D:driver1 /L:logical drive letter

For example, if C:\DOS\MSCDEX.EX /D:HPCD000 /L:E is used, the CD-ROM

drive is assigned to the DOS logical drive E: If you do not use option /L:E, the system

will automatically assign a DOS logical drive for the CD-ROM drive.

10. Power down your HP NetServer.

Section 4. Installing NetWare on the HP NetServer

This section details how to install SCSI, NIC, and HP NetRAID drivers from the NOS

Drivers Diskette created from the HP Navigator CD-ROM detailed in the section

Creating Drivers Diskette.

Netware 4.2 Installation

NOTE: Netware 4.2 installations with 4 GB of memory are known to fail

intermittently. If you have 4 GB of memory in your system, install Netware 4.2

using 3 GB of memory. Then after installation reinstall remaining memory.

NOTE: At least a 250 MB DOS partition must already exist on your hard drive

and your CD-ROM drive should be accessible. For detailed instructions refer to

Installing the CD-ROM Drive in DOS with FDATACD.SYS and MSCDEX.EXE.

1. Remove the HP NetServer Navigator CD-ROM and any floppy diskettes from the A:

drive and insert the Novell Netware 4.2 Installation CD into the CD-ROM drive.

2. Boot the HP NetServer into DOS.

3. Create a directory named NWUPDATE.

4. Copy all drivers from the NOS Drivers disk to the NWUPDATE directory.

NOTE: If you desire to use HP NetRAID series adapters in I20 mode, ensure the

appropriate drivers have been created from the HP NetServer Navigator CD-ROM

and copy them to the NWUPDATE directory you created and omit any drivers

for RAID.

5. After all drivers have been copied, change to the CD-ROM drive. From the CD-ROM

drive prompt enter the command:

Install

6. Select the desired language from the NetWare Install menu.

7. Review and accept the software license agreement by pressing Enter.

8. Using the arrow keys, highlight the product you would like to install and press Enter

(Instructions use Netware 4.2)

9. When prompted by the NetWare Installation Utility to select the type of installation

you are performing, highlight Custom installation of Netware 4.2 and press Enter.

10. Enter the Server name in the Server name: field and press Enter.

11. Enter the Internal network number in the Internal network number: field and press

Enter. (Instructions use default.)

12. If you wish to change the directory in which the server boot files will be copied, do so

at the Copy server boot files to the DOS partition screen. (Instructions use default)

13. Select the locale configuration for the server and press Enter.(Instructions use

default.)

14. When prompted by the NetWare Installation Utility to modify, add, or delete any

special startup set commands, select yes and add the following lines:

Set Minimum Packet Receive Buffers = 2500

Set Maximum Packet Receive Buffers = 15000

Save and continue by pressing F10.

15. Select No when prompted to Add commands to AUTOEXEC.BAT to load

SERVER.EXE.

NOTE: You may receive the following message:

Install found the following hardware but found more

than one driver supporting this hardware:

xxx.xxxx.xxxx.xxx.xxx

Press <F3> to continue without selecting.

The installation program for NetWare should load all drivers placed in the

NWUPDATE directory and match appropriate drivers to the hardware. When the

process is complete a driver summary will be displayed.

16. Under Additional Driver Actions ensure that you see the same instances of drivers

as controllers in your system. If you are using any HP NetRAID series adapter, ensure

that you see the same instances of drivers as adapters in your system. Also do the

same for any Network Adapters.

NOTE: HP NetServer LP 2000r and LP 1000r systems require that the second

instance of the IDEATA.HAM driver be deleted. Highlight the second instance

of the IDEATA.HAM driver, press delete, and continue with the installation.

17. If there is a driver missing, use Additional Driver Actions options to add the missing

driver. Otherwise, select Continue installation.

18. When prompted to Create NetWare disk partitions, highlight Manually and press

Enter.

19. Under Disk Partition and Mirroring Options highlight Create, delete, and modify

partitions and press Enter.

20. Under Available Disk Drives highlight first device and press Enter.

NOTE: You may receive the following message:

A partition table does not exist on this drive. If you

continue and create a disk partition, the table will

be created for you. (INSTALL-6.5.-139)

Press Enter and select Yes when prompted to initialize the partition table.

21. Under Disk Partition Options,highlight Create NetWare disk partition and press

Enter.

22. Under Disk Partition Information, make desired modifications. If you do not wish

to modify any information press F10 and choose Yes when prompted to Create

NetWare partition.

23. Once back at the Disk Partition Options,select Return to previous menu and

repeat steps 18 through 26 until all devices are partitioned.

24. After all devices are partitioned press F10 and select continue with installation from

the Disk Partition and Mirroring Options.

NOTE: Press Enter through any messages you may receive.

25. If you wish to modify any NetWare Volumes do so on the Manage NetWare

Volumes screen. If you do not wish to make any changes press F10 and select Yes to

continue installation.

26. If you wish to modify any Protocols do so on the Protocol Selection screen. If you do

not wish to make any changes select Continue with installation from the Protocol

Options menu.

NOTE: Press Enter through any messages you may receive.

27. If you wish to change the path where NetWare files will be installed, do so when

prompted. If you do not want to make any changes press Enter to continue.

NOTE: The installation program will proceed to copy NetWare files to your HP

NetServer. Wait till next prompt.

28. Enter a name for the Directory tree and press Enter.

29. Select your time zone and press Enter then F10 to continue.

30. Enter your company or Organization and press Enter.

31. Use the arrow keys to highlight the password field. Enter a password and press F10

to continue.

32. Select Yes when prompted to Save Directory Information and continue.

NOTE: Press Enter through any messages you may receive.

33. Insert NetWare License diskette into the floppy drive and press F3 and then Enter.

34. Edit the STARTUP file as necessary. If you do not wish to modify the

STARTUP.NCF file press F10 and select Yes to save a new STARTUP.NCF.

35. Edit the AUTOEXEC file as necessary. If you do not wish to modify the

AUTOEXEC.NCF file press F10 and select Yes to save a new AUTOEXEC.NCF.

NOTE: The installation program will proceed to copy NetWare files to your HP

NetServer. Wait till next prompt.

36. If you wish to install other items or products, do so on the Other Installation

Options screen. If not, highlight Continue Installation and press Enter.

NOTE: Refer to the Novell Netware 4.2 installation procedures for all other

installation issues. After completing the installation of Netware 4.2, you must

install the latest support pack from Novell. This can be downloaded from:

http://support.novell.com

Installing the SMP driver MPS14.PSM for Netware 4.2

The Netware 4.2 installation program no longer auto-detects more than one CPU and asks

the user if they wish to install SMP. SMP installation is now performed from the "install"

utility after the initial installation of Netware 4.2.

The installation program will attempt to add an older version of the SMP driver. The

correct SMP driver is located on the Netware 4.2 NOS driver diskette you created from

the NetServer Navigator CD in the a:\psm directory or will be loaded automatically with

the installation of Support Pack 7 or later.

Installing the NetRAID-1Si / NetRAID-3Si I2O driver on Netware 4.2

The HP NetRAID-1Si and NetRAID-3Si adapters can operate in either I2O or non-I2O

(traditional) mode. To configure the adapter to operate I2O mode use the NetRAID

Express Tools (version B.02.02 or later) that came with your NetRAID adapter or on the

NetServer Navigator CD. The I2O drivers are located on the Netware 4.2 NOS drivers

diskette in the \i2odac directory.

NOTE: I20 functionality is not supported on NetServer E series systems.

1. After the server installation process is complete, enter the commands:

DOWN

and press Enter. Followed by:

EXIT

and press Enter.

2. While in DOS copy the following files from the Netware 4.2 NOS drivers diskette

directory \i2odac to C:\NWSERVER:

IOPX.*

I2OPCI.*

BKSTROSM.*

SCSIOSM.*.

3. Then, while still in DOS, edit the STARTUP.NCF file and add the following lines:

Load bkstrosm.ham

Load scsiosm.ham

4. Next, from the C:\nwserver command prompt enter:

server

5. Use the NetWare install utility to create the necessary partitions and volumes.

Also load the NetRAID I2O compatibility driver, mril4_xx.ham, if:

- An HP NetRAID (D4943A) or HP NetRAID-1 (D4992A) is present in the system

(do not use the mega4_xx.ham driver in this case).

- You wish to use the Hewlett-Packard NetRAID Config for NetWare or the

Hewlett-Packard NetRAID Monitor for NetWare utility.

NOTE: Booting from the HP NetRAID-1si or HP NetRAID-3si using the I20

driver is not supported at this time. For more information, see your NetRAID

Adapter documentation.

NetWare 5.1 or NetWare Small Business Suite 5/5.1 Installation

Install NetWare 5.1 or NetWare Small Business Suite 5/5.1 according to the instructions

below. You may skip the steps that don't apply to the version of NetWare you are

installing.

NOTE: The NetWare installation program auto-detect feature attempts to match

hardware with the appropriate drivers. To run HP NetRAID-1Si or HP NetRAID-

3Si adapters in I2O mode, you will need to do it after the initial installation of

NetWare 5.1. See the section Completing the Installation of the HP NetRAID-

1Si/HP NetRAID-3Si I2O driver on NetWare 5.1/Small Business Suite 5/5.1.

NOTE: At least a 250 MB DOS partition must already exist on your hard drive

and your CD-ROM drive should be accessible. For detailed instructions, refer

back to the section Installing the CD-ROM Drive in DOS with FDATACD.SYS and

MSCDEX.EXE.

1. Remove the HP NetServer Navigator CD-ROM and any floppy diskettes from the A:

drive and boot your server into DOS.

2. Create a directory named NWUPDATE.

3. Copy all drivers from the NOS Drivers disk to the NWUPDATE directory.

4. Remove the NOS Drivers disk from drive A: and reboot your HP NetServer using the

NetWare CD-ROM, the NetWare 5.1 installation will automatically begin.

For NetWare 5.1

5. After reading the License Agreement, highlight Accept License Agreement and

press Enter.

6. Highlight Continue with Existing Partition and press Enter.

For Small Business Suite 5/5.1

7. When prompted to Create or keep a DOS Partition select Continue with existing

partition and click Next.

8. Click Yes to any warnings and Next to reboot and continue installation.

9. When prompted , select Standard or Advanced installation and click Next.

(Instructions use advanced.)

10. If prompted, Insert NetWare Small Business Suite 5/5.1 License diskette and press

Enter, then F10 to Accept License Agreement.

For both NetWare 5.1 and Small Business Suite 5/5.1

11. Select Upgrade or New server, then highlight Continue and press Enter.

(Instructions use New Server.)

12. Select server settings and Continue (instructions use the default settings).

13. Select regional settings and Continue (instructions use the default settings).

14. Select mouse and video mode and Continue (instructions use the default settings).

15. The Netware installation program will next attempt to detect the hardware in your

system and load an appropriate driver.

NOTE: You may receive the following message:

Multiple drivers were found that support the following

Adapter:

xxx.xxxx.xxxx.xxx.xxx

(For example, tc6100, rc7100, and tc7100 may prompt you to choose between a

HPTX.LAN or CHPTX.LAN driver.) If so, press F10 to continue - no selection.

16. The installation program for NetWare will load all drivers placed in the

c:\NWUPDATE directory and match appropriate drivers to the hardware. When the

process is complete a driver summary will be displayed. Driver names displays all

detected drivers. If you are using more than one CPU, ensure that MPS14 appears in

Autres manuels pour P5389A - Intel Pentium III-S 1.4 GHz Processor...

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Serveur

HP ProLiant DL560 Manuel utilisateur

HP T5720 - Compaq Thin Client Fiche technique

HP ProLiant DL320e Manuel utilisateur

HP Cluster Platform Introduction v2010 Manuel de référence

HP DL385 - ProLiant - G5 Instructions d'utilisation

HP Integrity rx4640 Manuel d'installation et d'exploitation

HP T5125 - Compaq Thin Client Manuel d'utilisation et d'entretien

HP ProCurve 6120G/XG Mode d’emploi

HP ProLiant SL250s Gen8 Manuel

HP ProLiant ML350p Gen8 Manuel utilisateur

HP Tc2120 - Server - 256 MB RAM Mode d’emploi

HP NetServer AA 4000 Manuel utilisateur

HP Integrity Superdome SX1000 Manuel utilisateur

HP ProLiant DL585 Instructions d'utilisation

HP ProLiant BL685c Generation 6 Manuel utilisateur

HP Rp3440-4 - 9000 - 0 MB RAM Manuel utilisateur

HP Integrity BL890c - i2 Server Mode d’emploi

HP ProLiant DL380 Manuel utilisateur

HP HPE ProLiant DL325 Manuel

HP D7171A - NetServer - LPr Manuel utilisateur

HP BL685c - ProLiant - 4 GB RAM Manuel utilisateur

HP t820 Manuel utilisateur

HP T5135 - Compaq Thin Client Manuel

HP HPE XL270d Instructions d'installation

Manuels Serveur populaires d'autres marques

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Dell

Dell PowerEdge HS5610 Manuel