HP D7171A - NetServer - LPr Manuel utilisateur
HP NetServer LH 3
with
A3661B High Availability Disk Array Model 30/FC
Cluster Configuration Guide
20 November 1998
Introduction
This document defines the supported HP NetServer LH 3 with A3661B High Availability Disk Array
Model 30/FC (LH 3/Model 30-FC) configurations for Microsoft Cluster Server. These configurations
minimize single points of failure, provide maximum availability, and have been certified by Hewlett-
Packard and Microsoft. This guide is prescriptive; it describes the HP NetServer LH 3 / Model 30-FC
configurations supported by HP. Any configuration not expressly allowed by this guide will not be
supported by HP.
What’s Defined in Cluster
Cluster
SPUs
Local and Shared Storage
Intra-cluster and Client LANs
Shared Storage Cabling
Cluster
Type of SPUs HP NetServer LH 3
Each node must be the same model SPU, but may have different size main
memory, cache, and CPU clock speeds.
Installation Pedestal or racked
Number of nodes 2
Shared Storage HP Rack Storage/8 with HP NetRAID controller and HP disks. See
Shared Storage below.
LANs:
Client LAN Any NIC that is HP and Microsoft approved. See Client LAN below.
Intra-cluster
(Heartbeat) LAN HP D5013A or J3171A only with crossover cable. See Intra-cluster LAN
below.
Power source Direct from power mains, power conditioner or uninterruptible power
supply (UPS) using any power conditioner or UPS.
2
System software:
Navigator version L.13.00 or later
Operating System Microsoft Windows NT Server 4.0, Enterprise Edition.
Service pack SP3 and hotfix "clusfixi", or later
SPU
Model HP NetServer LH3
Clock speed 350, 400 or 450 MHz.
No. of CPUs 2
BIOS version 4.06.25 PL or later
CPU cache Any size
RAM 128 MB minimum. Must be HP.
No. of power supplies 2 or 3
Local storage Must use HP disks. See
Local Storage below.
I/O slots: Shared storage controller. See
Shared Storage below.
P1 – Intra-cluster (Heartbeat) LAN
P2 – Client LAN
All others – Any other plug-in cards.
LANs
Intra-cluster (Heartbeat) LAN Client LAN
LAN connection HP D5954A crossover cable or any
equivalent. Any LAN
The intra-cluster LAN may only be
used for cluster node
communication via a crossover
cable. It may not be used for client
communication.
NIC:
Model HP D5013A (10/100TX PCI)
(or HP J3171A) Any that is on both the HP
Tested Products List and the
Microsoft Hardware
Compatibility List.
Driver 3.00.06.004 or later Any driver
If the NIC used is the same as
the Intra-cluster LAN, then the
Client LAN must use the same
driver as the Intra-cluster LAN.
No. of NICs 1 1 minimum
SPU I\O slot P1 P2
3
Storage
Local
Controller Any number, manufacturer or driver in any available I/O slot. However,
for NetRAID local storage use PCI slot P8.
Cabinets (Physical drive
location) SPU internal drive bays or HP external drive cabinet (e.g., HP Rack
Storage/8), any number.
Disk drives (hot swap
or fixed) Must be HP.
SCSI bus Any HP cables that meet SCSI specifications and any SCSI bus speed.
SCSI IDs Any
Shared
Host Bus Adapter:
Model A5246A HP Fibre Channel Adapter Kit for NT
No. of HBA 1 – 2. (See Shared Storage Configurations.)
Driver 2.09.B.038.020
SPU I/O slot P5 (1st HBA) and P6 (2nd HBA)
Disk Array Controller:
Model SP630/FC Storage Processor (ordered with A3661B or A3662B)
No. of controllers 1 – 2. (See Shared Storage Configurations.)
Microcode 9.45.03 or greater
Disk Array Storage:
Model A3661B HP High Availability Disk Array Model 30/FC.
No. of cabinets See Shared Storage Configurations.
Controller 1 – 2. (See Shared Storage Configurations.)
Disk capacities: 4 GB, 8.8 GB, 17.8 GB
ArrayGUIde Version 1.7.0 or greater
RAID levels 1, 1/0, 3 and 5
Logical units Logical units within each array must be numbered from 0 – 7.
Hot spares Recommend assigning logical unit numbers 8 or greater
Power Supply 3
RAID arrays Different size or speed disks are allowed in the same RAID array but
are not recommended in the same logical unit.
4
Shared Storage Cables (Fiber Optics)
Cables for Short Wave Port
of either the Short or Long
Wave Hub
A3583A 2 meter FC cable,
A3531A 16 meter FC cable,
A3735A 50 meter FC cable,
A3736A 100 meter FC cable,
Any cable ≤500 meters per segment that conforms to ANSI X3.230-
1994 Fibre Channel Standards Specification (FC-PH) rev 4.3.
Cables for Long Wave Port
of the Long Wave Hub Any cable ≤2 kilometers that meets ANSI X3.230-1994 Fibre Channel
Standards Specification (FC-PH) rev 4.3.
Shared Storage Configurations
Configurations:
Basic See "Basic Configuration Cabling Diagrams with Single or Cascaded
Hubs."
Redundant See "Redundant Configuration Cabling Diagrams with Single or
Cascaded Hubs."
Fibre Channel Hubs:
Model A3724A HP 10-port Short Wave Fibre Channel (FC) Hub
A4839A HP 10-port Long Wave FC Hub
No. of Hubs Basic Configuration: 1 or 2
Redundant Configuration: 2 or 4 with 1 min. or 2. max. per FC
Arbitrated Loop.
Disk Arrays (See Shared
Storage.):
No. of Disk Arrays 1-8
No. of Controllers 1 per Disk Array for Basic Configuration.
2 per Disk Array for Redundant Configuration.
5
Basic Configuration with Single Fibre Channel Arbitrated Loop Hub
Port connections to this
hub are for example
only. You can use any
port, except forport 10
on Long Wave Hubs.
The remaining ports can
be used for connection
of additional Disk Arrays.
See Shared
Storage Cables for
a list of cables that
can be connected
to the Short Wave
Ports of the hub.
6
Basic Configuration with Cascaded Fibre Channel Arbitrated Loop
Hubs
See Shared
Storage Cables for
a list of cables that
can be connected
to the Short Wave
Ports of the hub.
Port connections to
these hubs are for
example only. You can
use any port, except for
port 10 on Long Wave
Hubs. Theremaining
ports can be used for
connection of additional
Disk Arrays.
See Shared Storage
Cables for a list of
cables that can be
connected between
hubs. Port 10 is used
exclusively in Long
Wave hubs for hub-to-
hub connection.
7
Redundant Configuration with Single Fibre Channel Arbitrated Loop Hub
See Shared
Storage Cables for
a list of cables that
can be connected
to the Short Wave
Ports of the hub.
Port connections to
these hubs are for
example only. You can
use any port, except for
port 10 on Long Wave
Hubs. The remaining
ports can be used for
connection of additional
Disk Arrays.
8
Redundant Configuration with Cascaded Fibre Channel Arbitrated Loop Hubs
See Shared
Storage Cables for
a list of cables that
can be connected
between hubs.
Port 10 is used
exclusively in Long
Wave hubs for hub-
to-hub connection.
Port connections to
these hubs are for
example only. You
can use any port,
except for port 10on
Long Wave Hubs. The
remaining ports can
be used for
connection of
additional Disk Arrays.
See Shared
Storage Cables for
a list of cables that
can be connected
to the Short Wave
Ports of the hub.
Autres manuels pour D7171A - NetServer - LPr
117
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels HP Serveur
HP
HP SC20 Instructions d'utilisation
HP
HP D7171A - NetServer - LPr Manuel de la liste des pièces
HP
HP 3020 Mode d’emploi
HP
HP 124708-001 - ProLiant Cluster - 1850 Manuel utilisateur
HP
HP Carrier-grade cc3300 Manuel utilisateur
HP
HP Integrity rx2600 Manuel technique
HP
HP J3278B - SureStore CD-ROM Server/Tower 7 NAS... Manuel utilisateur
HP
HP Integrity Superdome 2 16-socket Manuel de service
HP
HP ProLiant ML110 Instructions d'utilisation
HP
HP t150 Manuel d'utilisation et d'entretien
HP
HP D7171A - NetServer - LPr Manuel utilisateur
HP
HP D7171A - NetServer - LPr Manuel d'exploitation et d'entretien
HP
HP ProLiant DL360p Instructions d'utilisation
HP
HP HP 3000 9 9KS Series Manuel utilisateur
HP
HP ProLiant ML310e Manuel utilisateur
HP
HP ProLiant SL160z - G6 Server Manuel utilisateur
HP
HP ML570 - ProLiant - G2 Instructions d'utilisation et de sécurité
HP
HP Apollo 2000 System Manuel
HP
HP T5135 - Compaq Thin Client Manuel de référence
HP
HP ProLiant BL e-Class Manuel
