HP Cluster Platform Hardware Kits v2010 Instructions de montage

Autres manuels pour Cluster Platform Hardware Kits v2010

8

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels HP Serveur

HP

HP ProLiant ML310 Generation 5p Manuel

HP

HP ProLiant BL460c G7 Manuel utilisateur

HP

HP ProLiant DL120 G7 Manuel utilisateur

HP

HP vc4815 - Thin Client Manuel utilisateur

HP

HP Gt7725 - Compaq Thin Client Manuel utilisateur

HP

HP ProLiant DL180 G5 Instructions d'utilisation

HP

HP Integrity rx4640 Manuel utilisateur

HP

HP ProLiant ML310e Gen Instructions de montage

HP

HP DL360 - ProLiant - Photon Manuel utilisateur

HP

HP T5720 - Compaq Thin Client Manuel utilisateur

HP

HP Integrity rx4640 Manuel utilisateur

HP

HP ProLiant DL60 Gen9 Manuel

HP

HP DL385 - ProLiant - G5 Instructions d'utilisation

HP

HP T5545 - Thin Client - 512 MB RAM Manuel utilisateur

HP

HP t5630 - Thin Client Instructions d'utilisation

HP

HP ProLiant DL360p Manuel utilisateur

HP

HP ProLiant BL460c G7 Manuel

HP

HP T5125 - Compaq Thin Client Manuel de service

HP

HP ProLiant ML115 G5 Guide de démarrage rapide

HP

HP L1000 - 9000 - 0 MB RAM Manuel utilisateur

HP

HP ProLiant DL145 Manuel utilisateur

HP

HP SA3150 Manuel

HP

HP LC2000r - NetServer - 128 MB RAM Manuel utilisateur

HP

HP D7171A - NetServer - LPr Manuel utilisateur

Manuels Serveur populaires d'autres marques

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Dell

Dell PowerEdge HS5610 Manuel

1

Rail Mounting Kit Installation Instructions

for the ProCurve Series zl Switches

The zl switches can be mounted with the optional Rail Mounting Kit (5070-0145) for shipment in an

HP 10000 series rack. These rails stabilize the switch, so the rack or cabinet can be shipped without

removing the switch. However, the power supplies must be removed from the chassis before shipping.

Note

The power supplies must be removed from the chassis before shipping in a rack.

Even though the illustrations show a Switch 5406zl, the instructions apply to all zl chassis models.

1. Use a posi-drive screwdriver, two included 8-mm M6 screws, and two included M6 cage nuts to

attach each rail to the rack or cabinet as shown in the following illustration. Ensure that the

screws are at the same level in each upright.

Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest

device at the bottom and progressively lighter devices installed above.

Figure 1. Attaching Rails to a Rack

8 mm

M6 screw

2

2. Use a #1 Phillips (cross-head) screwdriver and two included 8-mm M4 flat head screws to attach

a hold-down bracket to the chassis as shown in the following illustration. Ensure that each hold-

down bracket is positioned at the lower rear corners of the chassis.

Figure 2. Attaching Hold-Down Bracket

8 mm

M4 screws

Hold down

bracket

3

3. Use a #1 Phillips (cross-head) screwdriver to attach the mounting brackets to the switch with

the included 8-mm M4 screws. Each bracket is attached with four screws as shown in figure 3.

Figure 3. Attaching Rack Mounting Brackets

4. Slide the switch onto the rails in the rack until the mounting brackets are flush with the front

of the cabinet.

Figure 4. Notches in Bracket Being Installed

8 mm

M4 screws

Mounting

bracket

4

5. Install the four number 12-24 screws (included in the mounting bracket kit) into the upper and

lower holes in each bracket. Tighten these screws.

Figure 5. Installing screws in brackets

install and tighten the

other 12-24 screws

© Copyright 2006, 2007 Hewlett-Packard

Development Company, LP. All rights reserved.

The information contained herein is subject to

change without notice.

This document contains proprietary information,

which is protected by copyright. No part of this

document may be photocopied, reproduced, or

translated into another language without the

prior written consent of Hewlett-Packard.

Technical information in this document is

subject to change without notice.

Part Number: 5991-8559

August 2007

Printed in Singapore

*5991-8559*