HP BL680c - ProLiant - G5 Manuel utilisateur

HP ProLiant BL680c

Generation 5 Server Blade

Installation Instructions

Overview

Installation of a server blade requires the following steps:

1. Install and configure an HP BladeSystem c-Class enclosure.

2. Install any server blade options.

3. Install interconnect modules in the enclosure.

4. Connect the interconnect modules to the network.

5. Install a server blade.

6. Complete the server blade configuration.

For definitions of the acronyms used in this document, refer to

"Acronyms and abbreviations" in the server blade user guide.

Installing an HP BladeSystem

c-Class enclosure

Before performing any server blade-specific procedures, install an

HP BladeSystem c-Class enclosure.

The most current documentation for server blades and other

HP BladeSystem components is available at the HP website

(http://www.hp.com/go/bladesystem/documentation).

Documentation is also available in the following locations:

•Documentation CD that ships with the enclosure

•HP Business Support Center website

(http://www.hp.com/support)

•HP Technical Documentation website (http://docs.hp.com)

Installing server blade options

Before installing and initializing the server blade, install any server

blade options, such as an additional processor, hard drive, or

mezzanine card. For server blade options installation information,

see the HP ProLiant BL680c Generation 5 Server Blade User Guide

on the HP website

(http://www.hp.com/go/bladesystem/documentation).

Installing interconnect modules

For specific steps to install interconnect modules, see the

documentation that ships with the interconnect module.

Interconnect device mapping

To support network connections for specific signals, install an

interconnect module in the bay corresponding to the embedded

NIC or mezzanine signals.

The information contained herein is subject to change without notice. The

only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing

herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Part Number 452662-002

October 2007 (Second Edition)

Installation is shown in the HP BladeSystem c7000 Enclosure.

Server blade

signal

Interconnect bay Interconnect bay labels

NIC 1

(Embedded) 1

NIC 2

(Embedded) 2

NIC 3

(Embedded)

NIC 4

(Embedded)

Mezzanine 1 3 and 4

Mezzanine 2 5 and 6

7 and 8

Mezzanine 3 7 and 8

5 and 6

For detailed port mapping information, see the HP BladeSystem

enclosure quick setup guide or the HP BladeSystem enclosure setup

and installation guide on the HP website

(http://www.hp.com/go/bladesystem/documentation).

Connecting to the network

To connect the HP BladeSystem to a network, each enclosure must

be configured with network interconnect devices to manage

signals between the server blades and the external network.

Two types of interconnect modules are available for HP

BladeSystem c-Class enclosures: Pass-thru modules and switch

modules. For more information about interconnect module options,

see the HP website

(http://www.hp.com/go/bladesystem/interconnects).

Installing a server blade

HP BladeSystem enclosures ship with device bay shelves to support

half-height devices. To install a full-height device, remove the

device bay shelf and the corresponding blanks.

CAUTION: To prevent improper cooling and thermal

damage, do not operate the server blade or the enclosure

unless all hard drive and device bays are populated with

either a component or a blank.

Installation is shown in the HP BladeSystem c7000 Enclosure.

For detailed information on the c7000 or other BladeSystem

enclosures, see the appropriate enclosure setup guide or server

blade user guide.

Enclosure documentation is located at the HP website

(http://h71028.www7.hp.com/enterprise/cache/80316-0-0-0-

121.html).

Server blade documentation is located at the HP website

(http://h18004.www1.hp.com/products/servers/platforms/).

To install a server blade:

1. Remove the blank.

2. Remove the three adjacent blanks.

3. Slide the device bay shelf locking tab to the left to open it.

4. Push the device bay shelf back until it stops, lift the right side

slightly to disengage the two tabs from the divider wall, and

then rotate the right edge downward (clockwise).

5. Lift the left side of the device bay shelf to disengage the three

tabs from the divider wall, and then remove it from the

enclosure.

6. Remove the connector covers.

7. Prepare the server blade for installation.

8. Install the server blade.

CAUTION: To prevent improper cooling and thermal

damage, do not operate the server blade or the enclosure

unless all hard drive and device bays are populated with

either a component or a blank.

9. Install blanks in any empty bays. For more information, see

the enclosure setup and installation guide.

Completing the configuration

To complete the server blade and HP BladeSystem configuration,

see the overview card that ships with the enclosure and also see

the server blade user guide.

Autres manuels pour BL680c - ProLiant - G5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Serveur

HP Integrity NonStop i NS2300 Manuel technique

HP Performance Optimized Datacenter 40c North... Manuel

HP BCDVideo BCD108 Manuel utilisateur

HP Compaq Presario,Presario 4400 Mode d’emploi

HP Netserver LP 2000r Manuel utilisateur

HP StorageWorks P4000 Series Comment utiliser

HP ProLiant DL160 Generation 6 Instructions d'utilisation

HP ProLiant DL320 Generation 4 Manuel

HP ProLiant DL370 Generation 6 Guide d'installation

HP D7171A - NetServer - LPr Manuel utilisateur

HP T5720 - Compaq Thin Client Manuel

HP NetServer AA 4000 Instructions d'installation

HP t5740 - Thin Client Manuel utilisateur

HP ProLiant DL380p Instructions d'utilisation

HP EX475 - MediaSmart Server - 512 MB RAM Manuel utilisateur

HP ProLiant SL250s Gen8 Manuel utilisateur

HP 345646-001 - StorageWorks NAS 2000s External Storage... Manuel utilisateur

HP BladeSystem c3000 Instructions d'utilisation et de sécurité

HP Cloudline CL2100 G3 806R Mode d'emploi

HP t5400 - Thin Client Instructions d'installation et d'utilisation

HP NetServer LC 3 Manuel utilisateur

HP ProLiant DL360e Gen8 Manuel

HP LC2000r - NetServer - 128 MB RAM Manuel d'installation et d'exploitation

HP ProLiant ML100 Series Manuel utilisateur

Manuels Serveur populaires d'autres marques

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Dell

Dell PowerEdge HS5610 Manuel