HP StorageWorks 2312 Mode d’emploi

Ce manuel convient aux modèles suivants

1

Autres manuels HP Alimentation

HP

HP UPS R/T3000 Manuel utilisateur

HP

HP 6236A Manuel de service

HP

HP SCR-1P Series Manuel de service

HP

HP D7171A - NetServer - LPr Manuel d'installation et d'exploitation

HP

HP 6434B Manuel de service

HP

HP R6000 series Manuel utilisateur

HP

HP A Series Manuel de service

HP

HP HVB Series Manuel utilisateur

HP

HP FlexFabric 11900 2500W AC Manuel utilisateur

HP

HP ProCurve J8161A Manuel utilisateur

HP

HP HVB Series Manuel utilisateur

HP

HP Entry-Level Instructions d'utilisation

HP

HP J9405B Instructions de montage

HP

HP 6235A Manuel de service

HP

HP Lab Series Manuel d'instructions et de sécurité

HP

HP 640 RPS/EPS Manuel utilisateur

HP

HP J2962A Manuel d'installation et d'exploitation

HP

HP 6205C Manuel de service

HP

HP 6960A Manuel de service

HP

HP 6826A Manuel de service

HP

HP 6259B Manuel utilisateur

HP

HP 4142B Manuel utilisateur

HP

HP PSR650-A Manuel utilisateur

HP

HP 711A Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur

Elmdene

Elmdene G1380xN-y-s Series Manuel utilisateur

HP StorageWorks

2312/2324 Modular Smart

Array DC power supply

replacement instructions

© Copyright 2008 Hewlett-Packard Development Company, L.P.

First edition: November, 2008

The information in this document is subject to change without

notice.

Printed in China

www.hp.com

500919-001

About this document

This document details procedures for replacing a failed DC power

supply in an HP StorageWorks 2000 Family Modular Smart Array.

Before you begin

CAUTION:

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection:

•Keep the replacement component in the ESD bag until needed

•Wear an ESD wrist strap grounded to an unpainted surface

of the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Verifying component failure

Check the DC Voltage/Fan Fault/Service Required (bottom) LED:

•Amber = Fault condition

Disconnecting a DC power cable

IMPORTANT:

Use only the DC power cables provided with your product.

1. Verify that the main breaker to the rack is shut off prior to

disconnecting any DC connections.

2. Verify that all enclosure power switches are off.

3. Loosen the cable-locking screws attaching the D-shell connector to

the power supply.

4. Disconnect the power cable from the power supply.

5. Turn on the main breaker to the rack.

Removing a power supply

1. Turn the thumbscrew until it is disengaged from the module.

2. Rotate the latch downward to disconnect the internal connector,

and slide the module out.

Page 1

Installing a DC power supply

1. Slide the module into the slot as far as it will go.

2. Press the latch upward to engage the module; turn the thumbscrews

ﬁnger-tight

3. Connect a DC power cable to each power supply using the

D-shell connector. Use the up arrow on the shell to ensure proper

positioning before tightening.

4. Tighten the screws at the top and bottom of the shell with a torque

between 1.7 N-m (15 lb-in) and 2.3 N-m (20 lb-in) to attach the

cable securely to the DC power sources.

5. Turn on the main breaker to the rack.

6. Turn on the enclosure power switches.

Verifying component replacement

After replacing the module, check that the Input Power Good LED is on

and the DC Voltage/Fan Fault/Service Required (bottom) LED is off.

Additional information

See the MSA2000 web site: http://www.hp.com/go/msa2000.

Page 2