HP Visualize c160 Manuel utilisateur

RavenC160-180.FB -1 Wed Jul 10 14:00:20 1996

Installing the C160 to C180 CPU Upgrade

HP Part No. A4200-90018

E0796

Printed in USA

RavenC160-180.FB 0 Wed Jul 10 14:00:20 1996

Hewlett-Packard Co. 1996

Printing History

First Printing: July 1996

UNIX is a registered trademark in the United States and other countries,

licensed exclusively through X/Open Company Limited.

NOTICE

The information contained in this document is subject to change without

notice.

HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-

ble for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copy-

reproduced or translated to another language without the prior written con-

sent of Hewlett-Packard Company.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-

ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS

252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA

94304.

10 9 8 7 6 5 4 3 2 1

RavenC160-180.FB 1 Wed Jul 10 14:00:20 1996

Upgrading your Model C160 to a Model C180

Your upgrade kit contains a CPU board, which, when installed, upgrades

your Model C160 workstation to a Model C180 workstation.

The following sections provide step-by-step instructions for removing the

C160 CPU board and installing the C180 CPU board.

The general steps are outlined as follows. See the individual sections for

more detailed instructions.

NOTE: The following steps must be followed in the order in which they appear. Refer to the

individual sections of this guide for the actual step-by-step procedures for upgrading

the C160 to a C180.

• Determine the LAN ID of your system.

• Power off the workstation and any peripheral devices, unplug the power cords,

and disconnect any peripheral cables.

• Remove the main tray assembly.

• Remove the C160 CPU board from the main tray.

• Remove the memory boards from the C160 CPU board and reinstall them onto

the C180 CPU board.

• Install the C180 CPU board into the main tray assembly.

• Place the main tray assembly into the workstation chassis.

• Connect power cords and cables, restart the workstation, and enter the LAN ID

when prompted.

RavenC160-180.FB 2 Wed Jul 10 14:00:20 1996

Preparing Your Workstation

1Determine the workstations LAN ID by entering the following at the prompt:

/usr/sbin/lanscan

The output is similar to the following:

Hardware Station Dev Hardware Net-Interface NM Encapsulation Mjr

Path Address lu State NameUnit State ID Methods Num

2.0.2 0x08000970ECC0 0 UP lan0 UP 4 ETHER 52

After you install the new CPU board or I/O board and power on the system for

the ﬁrst time, you are prompted for the LAN ID. Record the information here so

you have a record of it:

EtherLAN ID ___________________-___________________

You must supply the dash (-) between the ﬁrst six digits and the last six digits.

2Power off your workstation by pressing the power button on the front panel.

When you press the power button, the workstation automatically shuts down the

operating system before it powers off the system.

3When the workstation has completed shutting down and powering off, power off

the monitor, and any peripheral devices connected to the workstation.

4Unplug the power cord of the system unit, the monitor, and any peripheral devic-

es from ac wall outlets.

RavenC160-180.FB 3 Wed Jul 10 14:00:20 1996

Preparing Your Workstation

5Unplug the power cord from the back of the system unit.

WARNING: To avoid electrical shock, make sure you unplug the power cable from

the wall outlet and the system unit before proceeding any further.

CAUTION: The internal components of your workstation are susceptible to mechanical and

electrostatic shock. To prevent such damage from occurring, observe the following

precauxtions during the installation procedure.

•Stand on a static-free mat

•Wearastatic-groundingwriststrap to ensure that any accumulated electrostatic charge

discharges from your body to ground. Attach the static-grounding wrist strap by fol-

lowing the instructions on the package that contains the strap. Be sure to attach one

end of the strap to the system chassis.

6Disconnect all cables, connectors, and terminators from the connectors on the

front and rear of the system.

7Remove the system unit from the floor stand, as shown in Figure 1.

Figure 1 Removing the Floor Stand

RavenC160-180.FB 4 Wed Jul 10 14:00:20 1996

Preparing Your Workstation

8Lay the system unit on a flat surface, such as a table top.

9Attach a static-grounding wrist strap to bare metal on the back of the system unit.

RavenC160-180.FB 5 Wed Jul 10 14:00:20 1996

Removing the Main Tray Assembly

1Completely loosen the four thumb screws on the rear of the system unit, as shown

in Figure 2.

Figure 2 Removing Main Tray Assembly

2Place one hand on the top of the system unit and push, while pulling the handle

on the rear panel with your other hand. See Figure 2.

3Slide the main tray assembly out of the chassis.

Thumb Screws

Thumb

Screws

RavenC160-180.FB 6 Wed Jul 10 14:00:20 1996

Removing the Model C160 CPU Board

1Remove the two CPU board retaining screws, as shown in Figure 3.

Figure 3 Removing the CPU Board

2Pull the two ejector handles at the same time, as shown in Figure 3.

3Slide the CPU board out approximately one inch, then lift it straight up to remove

it.

Retaining Screws

RavenC160-180.FB 7 Wed Jul 10 14:00:20 1996

Removing Memory Modules

1Locate the memory modules on the C160 CPU board, as shown in Figure 4.

Figure 4 C160 Memory Module Location

Memory Modules

RavenC160-180.FB 8 Wed Jul 10 14:00:20 1996

Removing Memory Modules

2To remove a memory module, push the ejector tabs on each side of the module.

Lift the memory module up and out of the connector and place it on a static-free

surface. Figure 5 shows how to remove a memory module.

Figure 5 Removing a Memory Module

Autres manuels pour Visualize c160

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Ordinateur de bureau

HP Kayak XU 03xx Manuel

HP Pavilion w1000 - Desktop PC Manuel utilisateur

HP TouchSmart IQ700 - Desktop PC Instructions d'installation

HP 280 G4 Manuel

HP Xw6400 - Workstation - 4 GB RAM Guide de référence rapide

HP Compaq HP dc7900 CMT Manuel utilisateur

HP Compaq dx2200 MT Series Manuel utilisateur

HP Vectra VE5 2 Manuel du produit

HP Pavilion t600 - Desktop PC Manuel utilisateur

HP Pavilion t458d Manuel utilisateur

HP Workstation xw4100 Manuel

HP Visualize j6000 Manuel utilisateur

HP ProDesk 600 G5 PCI MT Manuel

HP Z220 SFF Series Manuel utilisateur

HP Pavilion Elite m9170 Manuel utilisateur

HP IQ524 - TouchSmart - 4 GB RAM Manuel utilisateur

HP Pavilion t100 - Desktop PC Instructions d'installation

HP Bc1500 - BladeSystem - Blade PC Instructions d'utilisation

HP Compaq Presario Manuel

HP Pavilion Elite m9040n Manuel utilisateur

HP Pavilion MS214 Manuel utilisateur

HP Pavilion t300 - Desktop PC Manuel utilisateur

HP s3320f - Pavilion - Slimline Manuel utilisateur

HP Vectra VT6 Manuel

Manuels Ordinateur de bureau populaires d'autres marques

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur

Everex

Everex eXplora Manuel utilisateur

Lenovo

Lenovo ThinkCentre M75e Manuel utilisateur

Dell

Dell Alienware Area-51 R4 Manuel utilisateur