HP Compaq Presario Manuel
Upgrading and Servicing Guide
The only warranties for Hewlett-Packard products and services are set forth in the express
statements accompanying such products and services. Nothing herein should be construed as
constituting an additional warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
HP assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by HP.
This document contains proprietary information that is protected by copyright. No part of this
document may be photocopied, reproduced, or translated to another language without the prior
written consent of HP.
Hewlett-Packard Company
P.O. Box 4010
Cupertino, CA 95015-4010
USA
Copyright © 2000–2006 Hewlett-Packard Development Company, L.P.
May be licensed in the United States by one or both of U.S. Patents Nos. 4,930,158 and
4,930,160 until August 28, 2008.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. The Windows
logo and Windows Vista are trademarks or registered trademark of Microsoft Corporation in the
United States and/or other countries/regions.
HP supports lawful use of technology and does not endorse or encourage the use of our products
for purposes other than those permitted by copyright law.
The information in this document is subject to change without notice.
Table of Contents iii
Table of Contents
Safety Information...................................................................................1
Opening and Closing the PC.....................................................................1
Preparing the PC ...............................................................................................2
Before Opening the PC ......................................................................................2
After Closing the PC...........................................................................................3
Removing the Side Panel ....................................................................................3
Replacing the Side Panel ....................................................................................4
Removing the Front Panel....................................................................................5
Replacing the Front Panel ...................................................................................6
Locating Components Inside the Computer ...............................................7
Removing and Replacing Drives...............................................................8
Removing an Optical Drive.................................................................................8
Adding or Replacing an Optical Drive .................................................................9
Removing the HP Pocket Media or Diskette or Hard Disk Drive ..............................11
Adding or Replacing the HP Pocket Media or Diskette or Hard Disk Drive ..............13
Removing the Memory Card Reader ..................................................................15
Adding or Replacing the Memory Card Reader...................................................16
Removing the Hard Disk Drive...........................................................................17
Adding or Replacing a Hard Disk Drive .............................................................19
Adding Memory.....................................................................................22
Removing a Memory Module ............................................................................22
Installing a Memory Module .............................................................................23
Removing or Installing an Add-in Card...................................................24
Removing an Add-in Card ................................................................................25
Installing an Add-in Card..................................................................................26
Replacing the Battery.............................................................................27
iv Table of Contents
Upgrading and Servicing Guide 1
Upgrading and Servicing Guide
Safety Information
This product has not been evaluated for connection to an “IT” power system (an AC
distribution system with no direct connection to the earth, according to IEC 60950).
The Upgrading and Servicing Guide provides instructions on how to remove and replace
hardware components of your PC.
Opening and Closing the PC
WARNING: Please read “Safety Information” in the Warranty and Support
Guide before installing and connecting your system to the electrical power
system.
2Upgrading and Servicing Guide
Preparing the PC
Before you upgrade any component in your PC, you need to prepare the PC so that you
can safely handle it and the components.
Read the following items before attempting to upgrade or service the PC:
1These procedures assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required
for using and modifying electronic equipment.
2Write down and save the system model and serial numbers, all installed options, and
other information about the system. It’s easier to consult this information than to open
and examine the PC.
3It is recommended that you use an antistatic wrist strap and a conductive foam pad
when working on the system.
Before Opening the PC
To avoid injury and equipment damage, always follow this procedure in this order before
opening the PC:
1Remove any diskette or optical disc (CD or DVD) from the PC.
2Click the Windows Start Button®, and then click Shut Down.
3Disconnect the modem/telephone cable, if present.
4Disconnect the power cord from the electrical outlet and then from the PC.
5Disconnect all other attached cables (such as the keyboard, mouse, and monitor).
6Disconnect all external devices.
WARNING: Always disconnect the modem cord from the telephone system,
and then disconnect the PC from the power source before removing the front
and side panels of the PC. Failure to do so before you open the PC or do any
procedures can result in personal injury or equipment damage.
CAUTION: To reduce the risk of personal injury from electrical shock or hot
surfaces, disconnect the power cord from the wall outlet, and allow the
internal system components to cool before touching.
CAUTION: Static electricity can damage the electronic components of the PC or
optional equipment. Ensure that you are discharged of static electricity by
briefly touching a grounded metal object.
Upgrading and Servicing Guide 3
After Closing the PC
To avoid injury and equipment damage, always follow this procedure in this order after
closing the PC:
1Reconnect the power cord.
2Reconnect the modem/telephone cable and all other cables (such as the keyboard,
mouse, and monitor).
3Reconnect external devices.
4Turn on the PC and all peripherals such as the monitor.
5If you installed an add-in card, install any software drivers supplied by the card
manufacturer.
Removing the Side Panel
1See “Before Opening the PC” on page 2.
2Loosen the thumbscrew (A) that secures the side panel to the PC chassis. You may
need to use a screwdriver the first time you loosen the screw.
3Use the handle to pull and slide the panel back about 1 inch (2.5 centimeters), and
then lift it off the chassis.
WARNING: To reduce the risk of electrical shock, fire, or damage to the
equipment, do not plug telecommunications or telephone connectors into the
network interface card (NIC) (labeled as an Ethernet connector).
WARNING: Beware of sharp edges inside the chassis.
A
4Upgrading and Servicing Guide
Replacing the Side Panel
1Align the tabs at the bottom of the side panel to the ridge on the bottom of the chassis.
Place the side panel in the proper position on the chassis and slide it toward the front
of the chassis.
2Ensure that the hole for the thumbscrew aligns with the hole in the chassis, and then
replace the thumbscrew (A).
3See “After Closing the PC” on page 3.
A
NOTE: There is a 3mm gap between the top of the side panel and the top of the
chassis when the side panel is attached properly.
Upgrading and Servicing Guide 5
Removing the Front Panel
This procedure is necessary only when removing or replacing an optical drive, memory
card reader, an HP Pocket Media Drive, diskette drive, or the hard disk drive.
1Pull the three tabs (B) away from the outside edge of the chassis.
2Swing the front panel away from the chassis toward the left to remove it.
B
6Upgrading and Servicing Guide
Replacing the Front Panel
1Align and insert the three hooks on the left side of the front panel with the holes on the
left side of the chassis.
2Swing the front panel around and press the three hooks on the right side of the front
panel into the three holes on the right side of the chassis until the panel snaps into
place.
Autres manuels pour Compaq Presario
307
Ce manuel convient aux modèles suivants
23
Table des matières
Autres manuels HP Ordinateur de bureau
HP
HP Pavilion w1000 - Desktop PC Manuel utilisateur
HP
HP Z210 Series Manuel
HP
HP ProDesk 490 G3 MT Manuel d'utilisation et d'entretien
HP
HP Pavilion t3100 - Desktop PC Manuel utilisateur
HP
HP Omni Pro 110 Instructions d'utilisation
HP
HP Xw4200 - Workstation - 1 GB RAM Guide d'installation
HP
HP A524x - Pavilion - 512 MB RAM Instructions d'installation
HP
HP Compaq Presario Manuel utilisateur
HP
HP Model 745i - Workstation Manuel utilisateur
HP
HP Sprout Manuel utilisateur
HP
HP Pavilion t200 - Desktop PC Manuel utilisateur
HP
HP 280 Pro G3 Instructions d'installation
HP
HP Pavilion t100 - Desktop PC Comment utiliser
HP
HP PS988AV Manuel utilisateur
HP
HP dx2200 - Microtower PC Manuel utilisateur
HP
HP TouchSmart 320-1100 Manuel utilisateur
HP
HP Compaq dx2708 Microtower Manuel utilisateur
HP
HP Pavilion t600 - Desktop PC Manuel utilisateur
HP
HP Z820 Series Manuel utilisateur
HP
HP Workstation xw6000 Guide de référence rapide
