HP 748 Series Manuel utilisateur
Model 748 Workstation
Owner’s Guide
This guide contains installation instructions
HP Part No. A4511-90607
Edition E1199
Printed in U.S.A.
Hewlett-Packard Co. 1996, 1997, 1999
Printing History
First Printing: December 1996
Latest Printing: November 1999
UNIX is a registered trademark of The Open Group.
NOTICE
The information contained in this document is subject to change without
notice.
HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND
WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIM-
ITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall
not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance or use of this mate-
rial.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copy-
right. All rights reserved. No part of this document may be photocopied,
reproduced or translated to another language without the prior written con-
sent of Hewlett-Packard Company.
RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-
ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the
Rights in Technical Data and Computer Software Clause at DFARS
252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA
94304.
10 9 8 7 6 5 4 3 2 1
Contents
iii
Preface
Audience xii
Release Document(s) xii
Related Manuals xii
Revision History xiii
Documentation Conventions xiv
Questions, Suggestions, or Problems xv
1 Product Description
The Model 748 Ruggedized Workstation 1-3
Features 1-5
Model 748 Physical Dimensions and Power Requirements 1-6
Board Computer Configurations 1-7
Conversion Cables 1-7
2 Power Budget
Power Budgeting 2-3
3 VME Card Installation
VME Overview 3-3
VME Installation Outline 3-5
iv
Contents
Installing VME Accessory Card Hardware 3-6
Installation Procedures 3-6
For More Information 3-7
4 EISA Card Installation
EISA Accessory Card Configuration Files 4-3
Hardware Installation 4-4
Tools Required 4-4
Procedure 4-4
5 PCI Card Installation
Hardware Installation 5-3
6 Installing and Configuring Mass Storage Devices
Hardware Installation for Drives 6-3
Tools for Installation 6-3
Module Orientations 6-4
Finding the Status of Existing SCSI Bus Addresses 6-5
Current SCSI Addresses and Devices 6-5
Installing Mass Storage Devices 6-6
Installing a Device in the Mass Storage Module 6-7
Configuring for a Hard Disk Drive 6-10
Software Installation of the Hard Disk Drive Upgrade 6-10
The factory-set SCSI bus address for the disk drive 6-10
Contents
v
7 Using Mass Storage Devices
Using your CD-ROM Drive 7-2
CD-ROM Drive and CD-ROM Media Descriptions 7-3
CD-ROM Drive 7-3
CD-ROM Media 7-4
Operating the CD-ROM Drive 7-6
Loading and Unloading a CD-ROM in the Disc Tray 7-6
Verifying the CD-ROM Drive Operation 7-9
Mounting and Unmounting a CD-ROM Disc 7-11
Mounting a CD-ROM Disc Using SAM 7-11
Unmounting a CD-ROM Disc Using SAM 7-13
7-14
Reading the Busy Light 7-14
DDS Tape Drive and Data Cassette Descriptions 7-15
DDS Drive 7-15
High Humidity 7-18
Self-Test (Failure) 7-18
Media Wear (Caution) 7-18
Data Cassettes 7-19
Setting the Write-Protect Tab on a Data Cassette 7-20
Operating the DDS Tape Drive 7-22
Loading and Unloading a Data Cassette 7-22
Verifying the DDS Tape Drive Operation 7-23
Using Device Files 7-23
Archiving Data 7-24
Writing to a Data Cassette 7-24
Restoring Files from a Data Cassette to Your System 7-25
Listing the Files on a Data Cassette 7-25
Further Command Information 7-25
Ordering Information 7-27
vi
Contents
Using the Floppy Diskette 7-28
Setting the Write-Protect Tab on a Diskette 7-28
Inserting and Removing a Diskette 7-29
Operating the Floppy Drive 7-30
Verifying the Floppy Drive Configuration 7-30
Using Device Files 7-30
Formatting a New Diskette 7-31
Transferring Data To and From a Floppy Diskette 7-31
Saving Files to a Floppy Diskette 7-32
Restoring Files from a Floppy Diskette to Your System 7-32
Listing the Files on a Floppy Diskette 7-33
For More Information 7-33
Configuring the Floppy Driver 7-34
Ordering Information 7-35
8 Connecting Cables
9 Power-On/Power-Off
Powering On the System 9-2
Powering Off the System 9-4
10 Dealing With Problems
Interpreting the LED Indicators 10-3
Managing a Boot Failure 10-4
Boot Program Initializes Hardware 10-4
Recovering from a System Panic 10-5
Procedures for Recovering from a System Panic 10-7
Contents
vii
Dealing with Network Failures 10-11
A Safety and Regulatory Statements
Declaration of Conformity A-3
Special Video Configuration Statements A-4
For EN55022 or CISPR 22 Applications: A-4
For FCC Applications: A-4
Emissions Regulations A-5
Federal Communications Commission (FCC) A-5
VCCI Class A ITE A-5
A-5
Emissions Regulations Compliance A-6
Acoustics A-7
Regulation On Noise Declaration For Machines -3. GSGV A-7
Electrostatic Discharge (ESD) Precautions A-8
Safety Statement A-9
Laser Safety Statement (U.S.A. Only) A-10
Warnings and Cautions A-11
Glossary
viii
Contents
Figures
Model 748 Front View 1-3
Model 748 Rear View 1-4
Board Computer Front Panel 1-4
Model 744 Memory Slots 2-4
Installing a VME Card 3-6
Removing the EISA Tray 4-5
Card Retainer Screw 4-6
Sliding the EISA Module Back into the VMEbus Chassis 4-7
Removing the PCI Module 5-4
Card Retainer Captive Screw 5-5
Removing the Card Retainer and Slot Cover Plate 5-6
Installing a PCI Option Card 5-7
Installing the PCI Module into the VMEbus Chassis 5-8
Mass Storage Module: Typical Device Positions 6-4
Device Installation in the Mass Storage Module 6-8
CD-ROM Drive Controls and Features 7-3
CD-ROM Disc Tray 7-6
Placing a CD-ROM Disc in a Drive 7-7
Removing a CD-ROM Disc From a Drive 7-8
Tape Drive Controls and Indicators 7-17
Tape Drive LED Display Codes 7-17
Setting the Write-Protect Tab on a DDS Tape 7-21
Loading and Unloading a Data Cassette 7-22
Setting the Write-Protect Tab on a Floppy Diskette 7-28
Inserting and Removing a Floppy Diskette 7-29
SCSI Connections 8-3
Power Supply Connectors and Switches 9-2
Card Cage Power Switch 9-3
Contents
ix
Tables
Conversions to Standard Cabling 1-7
Model 744/132L Memory Card Current Usage Worksheet 2-5
Model 744/165L Memory Card Current Usage Worksheet 2-5
Model 744 Current Requirements Worksheet 2-7
Model 743 Current Requirements Worksheet 2-8
Internal Device Current Requirements 2-9
Upper Power Supply Current Budgeting Worksheet 2-10
Lower Power Supply Current Budgeting Worksheet 2-12
Supported Mass Storage Products 6-3
CD-ROM Controls and Features 7-4
DDS Tape Drive Capacities Without Data Compression 7-16
DDS Tape Drive Capacities With Data Compression 7-16
Summary of Possible Causes of Panics Problem Area and Action 10-6
System Panic Procedures 10-7
Problems with the Network 10-11
x
Contents
Table des matières
Autres manuels HP Ordinateur de bureau
HP
HP Compaq dc7100 DT Manuel d'installation et d'exploitation
HP
HP Compaq D315 Manuel d'utilisation et d'entretien
HP
HP Compaq dc5000 SFF Manuel d'utilisation et d'entretien
HP
HP Kayak XU Manuel
HP
HP MultiSeat ms6000 Fiche technique
HP
HP dx2420 - Microtower PC Manuel utilisateur
HP
HP Pro 2000 Manuel utilisateur
HP
HP Xw8400 - Workstation - 4 GB RAM Manuel utilisateur
HP
HP Blade bc1000 Manuel d'utilisation et d'entretien
HP
HP Compaq Presario Manuel utilisateur
HP
HP Pavilion a210 Instructions d'installation
HP
HP Compaq Presario Manuel utilisateur
HP
HP Pavilion a400 - Desktop PC Instructions d'installation
HP
HP Presario SR5400 - Desktop PC Manuel utilisateur
HP
HP Z240 Small Form Factor Manuel
HP
HP ProDesk 400 G1 Manuel utilisateur
HP
HP Vectra VL6 6 Manuel du produit
HP
HP Pavilion a400 - Desktop PC Manuel utilisateur
HP
HP Spectre x360 Manuel
HP
HP ProDesk 400 G1 Microtower Manuel d'utilisation et d'entretien
