HP StorageWorks 2312 Manuel utilisateur

HP StorageWorks 2312/2324

Modular Smart Array controller

installation instructions

© Copyright 1999, 2008 Hewlett-Packard Development Company,

L.P.

First edition: November, 2008

The informationinthisdocumentissubjecttochangewithout

notice.

Printed in the China

www.hp.com

508933-001

About this document

This document describes procedures for installing a controller into an

HP StorageWorks 2312/2324 Modular Smart Array.

Before you begin

CAUTION:

When upgrading an existing operational system with a second

optional controller, removing the air management blank impacts

the airﬂow and cooling ability of the device. To avoid possible

overheating, insert the controller as quickly as possible. If the

internal temperature exceeds acceptable limits, the enclosure may

overheat and automatically shut down or restart.

CAUTION:

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection.

•Keep the replacement component in the ESD bag until needed.

•Wear an ESD wrist strap grounded to an unpainted surface

of the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Installing a controller (single or dual) for

the ﬁrst time

Remove the air management blank(s)

NOTE:

For clarity, only relevant details are shown in these illustrations.

1. Turn the thumbscrews until the screws disengage from the blank.

1—Lat

ch 2—Thu

mbscrew

2. Press both latches downward.

Page 1

3. Pull the blank straight out of the enclosure.

Install controller(s)

NOTE:

For clarity, only relevant details are shown in these illustrations.

1. Loosen the thumbscrews; press the latches downward.

2. Slide the controller into the enclosure as far as it will go (1).

3. Press the latches upward to engage the controller (2); turn the

thumbscrews ﬁnger-tight.

4. Connect cables according to a supported conﬁguration. See the

user guide.

Upgrading an existing single controller

system to a dual controller

If you have an existing single controller system and you are adding a

second controller, the new controller automatically begins to initialize

when it is installed. If the ﬁrmware versions differ between the two

controllers, Partner Firmware Upgrade feature brings the older ﬁrmware

to the later ﬁrmware level.

Verifying Partner Firmware Upgrade is

enabled

By default the storage system’s Partner Firmware Upgrade feature is

enabled, so when you upgrade a controller the system automatically

ensures that both controllers have the more recent version.

•Log in to the command-line interface (CLI) and run the following

command to verify that Partner Firmware Upgrade is enabled.

show advanced-settings

If Partner Firmware Upgrade is disabled, enable it by running the

command:

set advanced-settings partner-firmware-upgrade

enabled

Verifying controller status

Once the controller completes initializing and is online:

•Verify that the heartbeat LED on the front of the enclosure is green.

•Verify that the OK LED on the back of the controller is green.

NOTE:

If the OK LED is blinking, the controller is still initializing.

Additional information

See the MSA web site: http://www.hp.com/go/msa.

Page 2

Ce manuel convient aux modèles suivants

1

Autres manuels HP Contrôleurs

HP

HP StorageWorks P2000 Mode d’emploi

HP

HP MSM720 Manuel utilisateur

HP

HP ProCurve MSM760 Manuel utilisateur

HP

HP A9890A - Smart Array 6402/128 RAID... Manuel utilisateur

HP

HP HPE MR Gen11 Manuel utilisateur

HP

HP netRAID-1M Manuel utilisateur

HP

HP StorageWorks HSG60 Manuel utilisateur

HP

HP 3100ES - Smart Array RAID Controller Manuel utilisateur

HP

HP ProCurve MSM710 Manuel utilisateur

HP

HP ProCurve MSM710 Manuel utilisateur

HP

HP HSG80 - StorageWorks RAID Array Controller Manuel

HP

HP 9000 Series 300 Manuel utilisateur

HP

HP StorageWorks P2000 Mode d’emploi

HP

HP MSM720 Manuel utilisateur

HP

HP Compaq Presario,Presario 4400 Mode d’emploi

HP

HP 166207-B21 - Smart Array 5302/32 RAID... Manuel utilisateur

HP

HP HSG80 - StorageWorks RAID Array Controller Manuel utilisateur

HP

HP MSA 2040 Mode d’emploi

HP

HP D5970A - NetServer - LCII Manuel utilisateur

HP

HP 30242 Manuel

HP

HP Smart Array P712m Instructions d'utilisation

HP

HP ProCurve MSM750 Manuel utilisateur

HP

HP Surestore Disk Array 12h - And FC60 Manuel utilisateur

HP

HP B120i Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur