HP E2492A Manuel utilisateur
About this Manual
We’ve added this manual to the Agilent website in an effort to help you support
your product. This manual is the best copy we could find; it may be incomplete
or contain dated information. If we find a more recent copy in the future, we will
add it to the Agilent website.
Support for Your Product
Agilent no longer sells or supports this product. Our service centers may be able
to perform calibration if no repair parts are needed, but no other support from
Agilent is available. You will find any other available product information on the
Agilent Test & Measurement website, www.tm.agilent.com.
HP References in this Manual
This manual may contain references to HP or Hewlett-Packard. Please note that
Hewlett-Packard's former test and measurement, semiconductor products and
chemical analysis businesses are now part of Agilent Technologies. We have
made no changes to this manual copy. In other documentation, to reduce
potential confusion, the only change to product numbers and names has been in
the company name prefix: where a product number/name was HP XXXX the
current name/number is now Agilent XXXX. For example, model number
HP8648A is now model number Agilent 8648A.
Installation Guide
Publication number E2492-92000
December 1997
Copyright Hewlett-Packard Company 1997
All Rights Reserved
HP E2492A Probe Adapter for
the Intel Deschutes Processor
Installation at a Glance
This Installation Guide explains how to install Hewlett-Packard’s
probe adapter for Intel Deschutes processors. This probing system
provides a quick and reliable connection from a Deschutes processor
to the HP E2487A Preprocessor Interface. The probe adapter contains
equipment and procedures for connecting to both slot 1 and slot 2
Deschutes processors.
Installation Overview
•Remove the processor card from the S.E.C. cartridge.
•Install the probe adapter assembly onto the processor card.
•Insert the processor card back onto the target system.
•Connect the preprocessor interface to the probe adapter.
2
Equipment Supplied
•Bottom clamp
•Interposer
•Probe head
•Fan and heat sink assembly
•Front-side cache heat sink assembly (required for slot 2 processors)
•Back-side cache heat sink assembly (required for slot 2 processors)
•Slot 1 card guides (2)
•Slot 2 card guides (2)
•Spring clips (6)
•This Installation Guide
Equipment Supplied
3
Minimum Equipment Required
•A target system with the processor card removed from the S.E.C.
cartridge. Detailed instructions for disassembling the S.E.C.
cartridge can be found in Intel’s S.E.C. Cartridge Disassembly
Application Note.
4
To disassemble the slot 1 S.E.C. cartridge
The slot 1 S.E.C. cartridge consists of a thermal plate, skirt, cover, and
processor card. The thermal plate, skirt, and cover must be removed to
access the processor card.
Detailed instructions for disassembling the slot 1 S.E.C. cartridge can be
obtained from Intel. The following procedures are only intended as an
overview.
Disassembling the S.E.C. cartridge voids the Intel warranty. Also, thereis ahigh
probability that the coverand thermal plate willbe destroyed during
disassembly, and a small possibility that the processor card will be destroyed.
The S.E.C. cartridge isnotintended to be reassembled after disassembly.
1Remove the slot 1 S.E.C. cartridge from the target system by pushing
in the two tabs on top of the cartridge, then pulling the cartridge up.
Removing the S.E.C. Cartridge
To disassemble the slot 1S.E.C. cartridge
5
2Using the instructions in the Intel S.E.C. Cartridge Disassembly
Application Note, insert a 1/8" small flat blade screwdriver between
the cover and the thermal plate, next to one of the four barbed posts
located at each corner of the thermal plate. Twist the screwdriver
until the barbed post pops free. Repeat this procedure for the other
barbed post at the same end of the cartridge, then repeat for the
other end of the cartridge.
Disassembling the S.E.C. Cartridge
3Using the instructions in the Intel S.E.C. Cartridge Disassembly
Application Note, separate the tabs on the thermal plate away from
the locator pins with fine-tip round nose pliers. Remove the spring
retainer clips, then separate the thermal plate from the processor
card.
4Remove any excess thermal grease from the processor heat spreader.
CAUTION Do not allow any thermal grease to get on the pads on top of the
microprocessor. The thermal grease could create an open electrical
connection between the probe head and the microprocessor.
To disassemble the slot 1S.E.C. cartridge
6
To disassemble the slot 2 S.E.C. cartridge
The slot 2 S.E.C. cartridge consists of a thermal plate, skirt, cover, and
processor card. The thermal plate, skirt, and cover must be removed to
access the processor card.
Detailed instructions for disassembling the slot 2 S.E.C. cartridge can be
obtained from Intel. The following procedures are only intended as an
overview.
Disassembling the S.E.C. cartridge voids the Intel warranty. Also, thereis ahigh
probability that the coverand thermal plate willbe destroyed during
disassembly, and a small possibility that the processor card will be destroyed.
The S.E.C. cartridge isnotintended to be reassembled after disassembly.
1Remove the slot 2 S.E.C. cartridge from the target system by pushing in the
two tabs on top of the cartridge, then pulling the cartridge up.
Removing the S.E.C. Cartridge
To disassemble the slot 2S.E.C. cartridge
7
2Using the instructions in the Intel S.E.C. Cartridge Disassembly
Application Note, insert a 1/8" small flat blade screwdriver between
the cover and the thermal plate, next to one of the four barbed posts
located at each corner of the thermal plate. Twist the screwdriver
until the barbed post pops free. Repeat this procedure for the other
barbed post at the same end of the cartridge, then repeat for the
other end of the cartridge.
Disassembling the S.E.C. Cartridge
3Using the instructions in the Intel S.E.C. Cartridge Disassembly
Application Note, separate the tabs on the thermal plate away from
the locator pins with fine-tip round nose pliers. Remove the spring
retainer clips, then separate the thermal plate from the processor
card.
4Remove any excess thermal grease from the processor heat spreader.
CAUTION Do not allow any thermal grease to get on the pads on top of the
microprocessor. The thermal grease could create an open electrical
connection between the probe head and the microprocessor.
To disassemble the slot 2S.E.C. cartridge
8
To connect to the slot 1 Deschutes target system
The Deschutes probe adapter connects to the slot 1 processor card once the
processor card has been removed from the S.E.C. cartridge.
Slot 1 Connection Overview
To connect to the slot 1Deschutestarget system
9
Table des matières
Autres manuels HP Adaptateur
HP
HP PCIe U320 Manuel utilisateur
HP
HP 656596-B21 Manuel utilisateur
HP
HP 332T Manuel utilisateur
HP
HP 381513-B21 - Smart Array P800 Controller... Manuel utilisateur
HP
HP StorageWorks FCA2684DC Manuel utilisateur
HP
HP A6826A Manuel utilisateur
HP
HP NC370F Manuel utilisateur
HP
HP Nc551m Instructions d'utilisation
HP
HP 614988-B21 Manuel utilisateur
HP
HP HP A5513A Manuel de la liste des pièces
HP
HP Model 744 - VME Workstation Guide de référence
HP
HP 697497-001 Manuel utilisateur
HP
HP TouchSmart 300-1000 - Desktop PC Manuel utilisateur
HP
HP BT400 Manuel utilisateur
HP
HP NC552SFP Manuel utilisateur
HP
HP 331FLR Manuel utilisateur
HP
HP Vectra VLi 8 Manuel utilisateur
HP
HP 347786-B21 - 8 Internal Port SAS HBA Manuel utilisateur
HP
HP P1980A Manuel utilisateur
HP
HP Presario S7000 - Desktop PC Manuel d'utilisation
