Hotpoint WMXTF922GUK Instructions d'utilisation et d'installation

Whirlpool UK Appliances Ltd

Service

Information

WASHING

MACHINE

SMALL DIGIT

Model Comm.

Covered Code

WMXTF922GUK 85885

5407926 Issue 1 April 2016

C00384298 ~ SM032030

Changes in this Issue

• Add New Model

* New Manual (First Issue)

2 of 27

Service Manual UK

Indesit

Company

English

SAFETY NOTES & GENERAL SERVICING ADVICE

1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance.

2. It should ONLY be used by suitably qualified persons having technical competence applicable

product knowledge and suitable tools and test equipment.

3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged)

from the electrical supply.

4. Servicing must be preceded by Earth Continuity, Earth Resistance and Insulation Resistance

checks.

5. Personal safety precautions must be taken to protect against accidents caused by sharp edges on

metal and plastic parts.

6. After servicing the appliance must be rechecked for Electrical Safety. In the case of appliances

which are connected to a water supply (i.e.: Washing Machines, Dishwashers & Food Centres etc.)

checks must be made for leaks from seals gaskets and pipe work and rectification carried out where

necessary.

7. It can be dangerous to attempt 'DIY' repairs / maintenance on complex equipment and the Company

recommends that any problem with the appliance is referred to its own Service Organisation.

8. Whilst the Company has endeavoured to ensure the accuracy of the data within this publication they

cannot hold themselves responsible for any inconvenience or loss occasioned by any error within.

9 These appliances are manufactured with a '3 phase' motor and uses a different type of power

module. This power board is fitted with a large aluminium heat sink which remains live after

the power is disconnected.

Under no circumstances should the board be removed under the time shown below.

Alternative 'quick methods' of discharging the board SHOULD NOT be used or attempted.!

IMPORTANT NOTE

Risk of Electric Shock

The metal heatsink fitted on the Power Module

may hold an electrical charge for a short period

after switching off the machine.

Allow 5 minutes after disconnecting the

machine from the electrical supply before

commencing ANY work.

3 of 27

Whirlpool UK Appliances Ltd

Service Manual UK English

INDEX

Safety & Servicing Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Index and Manufacturing Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Specifications & Introduction Dates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9

First Wash Cycle / Cleaning the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Controls & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 14

Controls Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Wash Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Special Wash Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Wiring Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Power Module Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Error Codes & Possible Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 - 24

Dismantling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 - 27

SERIAL NUMBER / INDUSTRIAL CODE EXPLANATION

Serial Number Example

3 10 02 0895

Four remaining digits = Build number that day 895th built

Third two digits = Day of manufacture 2nd of month

Second two digits = Month of manufacture October

First digit = Year of manufacture 2013

Industrial Code Example

37 24455 0010

Last four digits = 0000 original production.

Second five digits = COMMERCIAL CODE*

First two digits = Factory of origin

* Vital for correct model information and system identification

Other numbers denote major production changes

4 of 27

Service Manual UK

Indesit

Company

English

SPECIFICATIONS

Models Covered WMXTF922GUK (85885)

Colour G = Graphite

Country of Origin Factory 80 - Comunanza, Italy

Electrical Supply 220 - 240 Volt AC @ 50 Hz Fuse 13 amp

Energy Energy Class: A+++

Wash Load 9.0 kg Cottons

Spin Speed 1200 rpm

Water Supply Cold Valve - Coil Resistance 3.8 K:

Max Pressure = 1 Mpa (10bar)

Minimum Pressure = 0.05 Mpa (0.5bar)

Wash Heater 1800 Watts @ 230 volts Resistance 30:approx.

Thermistor NTC Resistance: 20 K:@ 20°C

Pump 2 Pole Synchronous

220 / 240 Volt 25 Watt, Resistance = 162 :

Door Lock P.T.C. Solenoid with emergency door release

Control Module Three Phase - Arcadia

Motor 3 phase induction motor CIM2/55 (50 stator)

195 V - 3A - 800 W - 310 Hz - 17500 rpm Ins Class F

Tacho 115.4 :@ 2.0 ± 7%

Weight 5.0 kg

Dimensions Height 850 mm Width 595 mm

Depth 605 mm Weight 73.4 kg Packed approx. 75.0 kg

5 of 27

Whirlpool UK Appliances Ltd

Service Manual UK English

WMXTF922GUK

6 of 27

Service Manual UK

Indesit

Company

English

INTRODUCTION DATES

Model: WMXTF922GUK

First Produced: October 2013

Location: Comunanza Factory (80) - Italy

Industrial Code: 80858850100

Controls: 3 Phase - Arcadia 2

Model: WMXTF922GUK

First Produced: May 2014

Location: Comunanza Factory (80) - Italy

Industrial Code: 80858850195

Controls: 3 Phase - Arcadia 2

Model Number Definition

Category Sub Brand

Display

Type Capacity

Spin

Speed rpm

Energy Efficiency

Colour

WM =

Washing

Machine

XT = Extra F - Small

Digit

6 = 6 kg

7 = 7 kg

8 = 8 kg

9 = 9 kg

1 = 1100

15 = 1500

2 = 1200

3 = 1300

35 = 3500

4 = 1400

5 = 1500

55 = 1550

6 = 1600

1 = A+

2 = A++

3 = A+++

P = Polar White

G = Graphite

X = Stainless

K = Black

Washing Extra Small 9 kg 1200 rpm Graphite Country

WM XT F 9 2 2 G UK

A+++

Digit

7 of 27

Whirlpool UK Appliances Ltd

Service Manual UK English

INSTALLATION

Unpacking

1. Unpack the washing machine and check whether the it has been damaged during transport.

If this is the case, do not install it and contact the retailer.

2. Remove the four protective screws (transit bolts) and the rubber washer with the respective spacer,

situated on the rear of the appliance (see Figures below).

3. Fit the blanking plugs provided into the holes vacated by the bolts.

4. Use the plug provided to seal the holes where the mains plug was housed (if supplied), situated on

the lower right hand side on the rear of the appliance.

5. Keep all the removed parts as they will be required again if the washing machine needs to be

moved to another location.

Levelling

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, cabinets etc.

2. Compensate for any unevenness by tightening or loosening the adjustable front feet. The angle of

inclination, measured according to the worktop must not exceed 2°.

Levelling the appliance correctly will provide it with stability and avoid vibrations, noise and shifting

during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow

enough room for ventilation underneath the appliance.

This raised part is attached to the polystyrene base

and should have been removed when unpacking. Remove 4 transit bolts.

8 of 27

Service Manual UK

Indesit

Company

English

Connecting the water inlet hose.

Before making the water

connection to the 3/4"

thread, allow the water

freely from the supply tap

until it is perfectly clear.

Check that seal is in place

inside the hose end cap.

Connect the other end of

the water inlet hose to the

washing machine,

screwing it onto the cold

water inlet, situated on the

top right-hand rear of the

appliance - see

illustration.

Screw the inlet end with the blue cap onto the cold water supply tap.

Turn the tap on and check for leaks: tighten if necessary.

Make sure there are no kinks or bends in the hose.

The water pressure at the tap must be within the values indicated in the

Specifications page.

9 of 27

Whirlpool UK Appliances Ltd

Service Manual UK English

DRAINAGE CONNECTIONS

A. Connect the drain hose, without kinking it, to a

draining duct or a wall drain fixed at a height

between 65 and 100 cm from the floor. See Fig. 1.

B. Alternatively, place it over the edge of a basin, sink

or tub, fastening the hose supplied to the tap.

See Fig. 1.

The free end of the hose should not be under water.

Note: We advise against the use of hose

extensions. In case of absolute need, the extension

must have the same diameter as the original hose

and must not exceed 150 cm in length.

Undersink Connections:

The drain hose may be connected to an undersink trap.

Before connecting the drain hose from the machine

ensure that any blanks or removable ends have been

taken off the spigot. See Fig. 2.

Note: The hose must also be raised up in a similar way

to a standpipe installation to prevent backflow of waste

water from the sink into the machine. See Fig. 1.

Electrical Connections

Before plugging the appliance into the mains socket, make sure that:

- the socket is earthed and in compliance with the applicable law.

- the supply voltage is included within the values indicated in the Specifications page.

- the socket is compatible with the washing machines plug. If this is not the case, replace the socket

or the plug.

Location

! The washing machine should not be installed in an outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.

! When the washing machine is installed, the mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or dangerously compressed.

! The power supply cable must only be replaced by an authorised serviceman.

WARNING!

The company denies all liability if and when these warnings are not respected.

The first wash cycle

Once the appliance has been installed and before you use it for the first time, run a wash cycle with

detergent and no laundry, using programme 'Auto Clean'.

Fig. 1

Fig. 2

10 of 27

Service Manual UK

Indesit

Company

English

FIRST WASH CYCLE / CLEANING THE MACHINE

Cleaning the Washing Machine

• The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or abrasives.

• The washing machine has a 'Auto Clean' programme for its internal parts that must be run with

no load in the drum.

To help the wash cycle you may want to use either the detergent (i.e. a

quantity 10% the quantity specified for lightly-soiled garments) or

special additives to clean the washing machine. We recommend

running a cleaning programme every 40 wash cycles.

To start the programme press button A for 5 seconds (see figure).

The programme will start automatically and will run for about 70

minutes. To stop the cycle press the START/PAUSE button.

Detergent Dispenser Drawer

Successful washing results also depend on the correct dose of detergent: adding too much detergent

will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your

appliance and contribute to environmental pollution.

! Use powder detergent for white cotton garments, for pre-washing, and for washing at

temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents; they create too much foam.

Open the detergent dispenser drawer and pour in the detergent or

washing additive, as follows.

! Do not pour detergent into the middle compartment (*). Detergent

should only be poured into the compartment 1.

Compartment 1: Detergent for the wash cycle (powder or liquid)

If liquid detergent is used, it is recommended that the removable plastic

partition A (supplied) be used for proper dosage.

If powder detergent is used, place the partition into slot B.

Compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Compartment 1

Compartment 2

Table des matières

Autres manuels Hotpoint Rondelle

Hotpoint

Hotpoint VWSR4150D Manuel utilisateur

Hotpoint

Hotpoint WMYL 6151 Manuel utilisateur

Hotpoint

Hotpoint WMF 940 P Manuel utilisateur

Hotpoint

Hotpoint Aqualtis AQXXL 149 PI Manuel utilisateur

Hotpoint

Hotpoint ARTXF 109 Manuel utilisateur

Hotpoint

Hotpoint FIRST EDITION FIRST EDITION WMA10 Mode d’emploi

Hotpoint

Hotpoint VLXR1020T Manuel utilisateur

Hotpoint

Hotpoint WMSD 601 Manuel utilisateur

Hotpoint

Hotpoint WMD 742 Manuel utilisateur

Hotpoint

Hotpoint Aqualtis AQ113L 297I Manuel utilisateur

Hotpoint

Hotpoint WMFG 651 Manuel utilisateur

Hotpoint

Hotpoint 9517 Mode d’emploi

Hotpoint

Hotpoint VVSR1070 Manuel utilisateur

Hotpoint

Hotpoint AQXXF 149 H PI Manuel d'instructions

Hotpoint

Hotpoint WM72 Manuel utilisateur

Hotpoint

Hotpoint WMD 9692 P Manuel utilisateur

Hotpoint

Hotpoint Aqualtis AQ113F 497 I Manuel utilisateur

Hotpoint

Hotpoint G155 Manuel utilisateur

Hotpoint

Hotpoint HSWP1000MWW Manuel utilisateur

Hotpoint

Hotpoint AQXXF 129 P Manuel utilisateur

Hotpoint

Hotpoint WDD 750 Manuel utilisateur

Hotpoint

Hotpoint WMD 942 Manuel utilisateur

Hotpoint

Hotpoint AQXXD 169 PM Manuel utilisateur

Hotpoint

Hotpoint FUTURA HF6D 551 Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur