Hoover Nextra Manuel de programmation

2004

Picture

HOOVER "NEXTRA" FRONT LOADING WASHING MACHINES:

A)Starting the Auto-test Sequence:

•Push and hold the 1st Option's Buttonfrom left (Ref. 1 in Picture 1).

•Turn the Knob of the Program's Selector 2 steps in clockwise sense.

•As soon as the LED of the 1st Option's Button comes up lighted, release the button.

•All LEDs of Control Panel are

lighted together (see Picture 2):

•After 3 seconds and within 5

seconds, push again the Option's

Button n. 1 (see Picture 2).

•Once the Auto-test is correctly

initialized, the two rows of the

LEDs of Residual Time and of the Option's Buttons start flashing alternatively. Fro this

moment onward, the Auto-test Checking Routine sequence is carried out automatically,

as it's next described:

B)Description of the Sequence of Auto-test:

B1) Water load to the basic level (through detergent compartment n. 1 (Pre-wash), carried out

through the Cold Water Solenoid Valve (and Hot Water Valve too, when present. If

present, it's fed the Recycle Pump.

B2) 1 second pause.

B3) It's fed for 16 seconds the Water Heating Element (9.10 A on digital ammeter); the water

distribution cam moves the Water Spray Nozzle over the detergent compartment n. 2

(Wash).

B4) Are simultaneously fed the Solenoid Valve for Cold Water (and for Hot Water, when

present), the Recycle Pump (when present) and the main Motor, to tumble the Drum at

55 rpm in counterclockwise sense, for 13 seconds.

B5) Motor is paused for 15 seconds. Water load continues, as above described.

B6) Are simultaneously fed the Solenoid Valve for Cold Water (and for Hot Water, when

present), the Recycle Pump (when present) and the main Motor, to tumble the Drum at

55 rpm in clockwise sense, for 13 seconds. In this phase, if the Option's Button n. 3 is

pushed (see Picture 2), the Drum's speed of revolution can be reduced from 55 to 35

rpm.

B7) It's fed the Drain Pump, until the Pressure Switch is tripped to the "Empty Tank"

condition.

B8) It's carried out a short Spin Sequence, lasting 27 seconds, at the half of the maximum

speed available. End of the Auto-test routine.

2004

Figura 3

C) TROUBLESHOOTING AND DISPLAYING OF THE ERROR CODES:

All Washing Machines belonging to the new

Hoover "Nextra" range, are supplied with a

peculiar software, capable of recognizing and

displaying the Error Codes corresponding to the

most important troubles that may happen, both

during the normal Washing Cycle than during the

carrying out of the Auto-test routine.

Each time a serious trouble happens, the related

Error Code is stored into the EEprom memory, the

currently running washing cycle (or Auto-test) is

halted and the same Error Code is displayed. This

is a valid help to the Service Technician, in order

to make easier the identification of the reason of

the trouble.

The Error Codes are displayed by making flash simultaneously the START LED and the LED

OF THE 1st OPTION'S BUTTON (see Picture 3).

The length of each displaying of an Error Code is 15 seconds. During this period of time, both

LEDs flash together at the frequency of 1 Hz (1 flash per second), the number of their flashes

in the 15 seconds period being the actual Error Code. After the Code was displayed, both

LEDs stay OFF until the end of the 15 seconds period. Then, the sequence is repeated.

Example: Error Code n. 2 (missing completion of the water load, within the designed limit

time) is so displayed:

•2 flashes by the 2 LEDs together, in the 1st 2 seconds (0.5" ON –0.5" OFF).

•13 seconds both LEDs are switched off.

•The sequence as above is repeated.

D)LIST OF THE PRESENTLY AVAILABLE ERROR CODES:

Error

Code Number of

Flashes by

2 LEDs

Time the

2 LEDs

stay OFF

Possible reason of the Error Warning:

Error 1 114 Door Lock Safety Device open circuit and/or Wiring.

Error 2 213 Missing completion of the Water Load Phase, within

the designed limit time of 5 minutes and 18 seconds,

due to Low Hydraulic Pressure, faulty Solenoid Valve

and/or clogged Fill Hose.

Error 3 312 Missing completion of the Water Drain Phase, within

the designed limit time of 6 minutes, due to clogged

Pump's Filter and/or clogged Drain Hose or clogged

domestic drain system.

2004

Error

Code Number of

Flashes by

2 LEDs

Time the

2 LEDs

stay OFF

Possible reason of the Error Warning:

Error 4 411 3 sequential operations by the Anti-flood Contacts of

the Pressure Switch, due to Mechanically Blocked

Opened Solenoid Valve or faulty Pressure Switch.

Error 5 510 Faulty NTC Temperature Reading Probe and/or Wiring

and/or "Core" Board. Ohmic values of NTC Probe are:

20 Kohm at 25°C–2.14 Kohm at 85°C.

Error 6 69Defective "Core" Control Board.

Error 7 78Main Motor's Rotor is jammed.

Error 8 87

Short or Open Circuited Motor's Tachometric Dynamo

and/or Wiring. Ohmic values of Tacho's Coil as follows:

Ohmic Value with Ceset Motor: 42 Ohm

Ohmic Value with Hoover Motor: 156 Ohm

Ohmic Value with Sole Motor: 184 Ohm

Error 9 96Short Circuited Motor's Triac on the "Core" Control

Board and/or defective "Core" Control Board.

Error 10 10 5Faulty Program's Selector and/or Wiring.

Error 0

14 1Faulty Wiring and/or defective "Core" Control Board.

Making reference to the above resuming table of the available Error Codes, we like to remind

the importance of the perfect continuity of the electric wiring and of the related connectors,

when dealing with electronic controls of the "Core" family. This is both true for the contacts on

the Control Board then for the corresponding contacts on the controlled peripherals (Program's

Selector, Display Board, etc.)

A partial oxidation of some connector's contacts on the "Core" Control Board (or on the

connected peripherals, such as the Program's Selector and the Door Lock Safety Device),

could generate the displaying of a peripheral related Error Code, even being the involved

peripheral in perfect conditions.

Therefore, we suggest to carefully check the related wiring, before any replacement of the

"Core" Control Board and before replacing any of the related peripherals.

A valid check of the wiring can be performed by removing the connectors from their location

(both on the Control Board then on the related Peripheral) and by spraying inside the same

connectors a small amount of Contact Cleaner liquid. Then, re-fit the connector in position and

re-start the Auto-test routine, to see if the Error Warning is displayed again.

Best regards.

GIAS S.r.l.

Autres manuels pour Nextra

Table des matières

Autres manuels Hoover Rondelle

Hoover

Hoover Dynamic Next Premium DXP 410AIB3 Manuel utilisateur

Hoover

Hoover H-WASH 500 HW 48AMC/1-S Manuel utilisateur

Hoover

Hoover HWE 410AMBS/1-S Manuel utilisateur

Hoover

Hoover VHD ZD Manuel utilisateur

Hoover

Hoover DXA 385AH/1-AUS Manuel utilisateur

Hoover

Hoover DXO4 H7A2TCEX-S Manuel utilisateur

Hoover

Hoover 1300 SPECIAL EDITION PE235 Manuel utilisateur

Hoover

Hoover VHD 614 Manuel utilisateur

Hoover

Hoover H 120 E Manuel utilisateur

Hoover

Hoover Performa Plus Manuel utilisateur

Hoover

Hoover Washing machine Manuel utilisateur

Hoover

Hoover Computer Control 1100 A3268 Manuel utilisateur

Hoover

Hoover WDYN 10743D Manuel utilisateur

Hoover

Hoover SE160 E Manuel utilisateur

Hoover

Hoover DWT L68AIW3/1-80 Manuel utilisateur

Hoover

Hoover HNL 6106 Manuel utilisateur

Hoover

Hoover AC154 Manuel utilisateur

Hoover

Hoover OH 120 M7 VARIO Manuel utilisateur

Hoover

Hoover AWMPD 49LH7/1-S Manuel utilisateur

Hoover

Hoover HBWS 49D2ACE Manuel utilisateur

Hoover

Hoover H-WASH 700 Manuel utilisateur

Hoover

Hoover HWDP610AMBC/1-S Manuel utilisateur

Hoover

Hoover VTS D2 Manuel utilisateur

Hoover

Hoover HF7 12 I Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur