Honeywell Ex-Or LS3043DR Manuel utilisateur

QuickSetPro

Programmer

Page 1 of 5

Quick User Guide

(Commissioning LS3100R/RM /RH series switching detectors)

Pointing QSP at detector being programmed

press the download button. The QSP will

communicate with the detector via an IR signal

path and begin to download the settings from the

detector. The QSP should remain pointing at the

detector until a ‘Download Summary’ is displayed

on the screen.

Press ‘ok’ to then view the details.

QuickSetPro

Programmer

Page 2 of 5

The

next screen details the ‘product wide’

parameters.

Using the Up/Down/Left and Right Keys you can

navigate down the list and make any

amendments to the settings.

On a switching only detector such as the LS3100R

you would set the appropriate light levels for the

detector to switch lights on (P’cell Turn ON) and

off (P’cell Turn OFF) or hold lights off regardless

of occupancy at this screen.

Please be mindful to keep a hysteresis between

the ON & OFF setpoints to prevent ‘hunting’.

Pressing the top left ‘soft key’ navigates you to

the next view – ‘Channels’.

On this screen the occupancy trigger mode (i.e.

presence or absence) and the time out delay can

be accessed for editing

o change the ‘Occupied Timer

’

–

this

is the

time

out period after last occupancy is detected for the

unit to time out to its ‘When Vacant’ state:

Press the ‘Down’ and/or ‘Left’ key until the

‘Occupied Timer’ is boxed and the setting (in this

case the default ’20 mins’) is highlighted.

Press ‘ok’ to bring up options allowed for this

parameter.

Use the ‘Up’ and ‘Down’ keys to navigate the list

until the desired setting (e.g. 2 mins) is

highlighted then ‘Ok’ to select.

QuickSetPro

Programmer

Page 3 of 5

If required select and edit other parameters using

the method described above.

When all changes have been made upload the

new settings into the detectors by pressing the

‘Upload’ key whilst holding the QSP aiming at the

detector (similar to the download function).

Once complete an ‘Uploaded Successfully’

message will be displayed.

The photocell then needs to be calibrated to ensure the detector turns on and off at the correct levels.

This is achieved by following the calibration routine on the following page:

QuickSetPro

Programmer

Page 4 of 5

Set the photocell

Go to the ‘Utilities’

menu by highlighting and

pressing ‘OK’.

hen highlight ‘LightSpot HD

’ and press ‘OK’.

Highlight ‘Photocell Calibration

’ and press ‘OK’.

You can then find out

1) Whether the photocell has been

previously calibrated by highlighting

‘Status’ and pressing ‘OK’ whist

pointing the QSP at the detector in

question.

2) Perform a simple calibration

3) Perform an advanced calibration

QuickSetPro

Programmer

Page 5 of 5

Simple Calibration

Highlight ‘Simple Calibration’ and press ‘OK’.

This brings up the calibration screen. The

luminaires should, at this point, be on at full.

With your Light Meter on t

he working plane set

the actual ‘Lux’ level detailed on the meter into

trhe QSP using the ‘Up’ and ‘Down’ keys. Once

the level is correct press ‘Ok’ to store this into the

detector.

Autres manuels Honeywell Capteur de sécurité

Honeywell

Honeywell FS24X Manuel utilisateur

Honeywell

Honeywell SiX Series Manuel utilisateur

Honeywell

Honeywell RAELink3 2.4GHz Manuel utilisateur

Honeywell

Honeywell Smart Seal P3S Manuel utilisateur

Honeywell

Honeywell Sensepoint XCD Manuel utilisateur

Honeywell

Honeywell FS20X Series Manuel utilisateur

Honeywell

Honeywell IS2535T Manuel utilisateur

Honeywell

Honeywell FlexGuard 5853AP Manuel utilisateur

Honeywell

Honeywell C554A Manuel utilisateur

Honeywell

Honeywell V-Plex IS3050A-SN Manuel utilisateur

Honeywell

Honeywell MILLER 1032363 Manuel utilisateur

Honeywell

Honeywell Miller 8172 Manuel de l'opérateur

Honeywell

Honeywell CLLRF2OCR2BP Manuel utilisateur

Honeywell

Honeywell Notifier FST-951 Manuel utilisateur

Honeywell

Honeywell Notifier FSP-951AUS Manuel utilisateur

Honeywell

Honeywell krom schroder DGS Manuel utilisateur

Honeywell

Honeywell Miller DuraHoist Manuel de l'opérateur

Honeywell

Honeywell SiXCOMBO Manuel utilisateur

Honeywell

Honeywell Notifier NRX-TFIX58 Manuel utilisateur

Honeywell

Honeywell Connected Home CAMIR-8EZS Manuel utilisateur

Honeywell

Honeywell FlexGuard 5853 Manuel du propriétaire

Honeywell

Honeywell IntelliSense FG-1625RFM Manuel utilisateur

Honeywell

Honeywell FG8M Manuel utilisateur

Honeywell

Honeywell SiX Series Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur