Honeywell AUTOCUBE 8200 Manuel utilisateur

AutoCube 8200

Quick Start Guide

AUTOC-EN-QS-01 Rev D

6/17

Out of the Box

Make sure your shipping box contains these items (full kit):

• AutoCube camera with protective foam

• Stand with cable(s) and clamps

•4cablecovers

• Stand clamp

• Display and display holder (optional accessories)

• Mounting hardware

• Stand base cover

Unpacking the Box Contents

Carefully unpack the box contents.

Caution: Do not remove the protective foam from

the camera during installation.

Caution: Do not open the AutoCube camera! The

warranty and certification is void if this

stipulation is ignored. The device may only

be opened by authorized persons.

What You Need

• Drill with a Ø12.5 mm drill bit

•Measuringtape

• Allen wrench, 3 mm and 5 mm

• Adjustable wrench

• Hole saw Ø32 mm (optional)

•Pliers(optional)

• Phillips screw driver (optional)

Installation Overview

Dimensions

The following are the recommended dimensions for installation.

The camera angle (A) and distance from the pole to the center of

the measurement area (D) vary depending on pole height (H).

Note: If you are not using the pole, the camera height (H),

measured from the front center of the camera, should be

≈1.5 m / ≈5 ft or ≈1.8 m / ≈ 6 ft.

Before You Begin

Determine where you will place the stand and if the cables will

exit through the bottom of the stand (going through the mount-

ing surface) or the side of the stand.

Prepare the Mounting Surface

Use the stand clamp as a template to trace and drill 4 holes (12

mm diameter) in the mounting surface.

Note: If the cables will exit through the bottom of the pole and

through the mounting surface, you must also drill the

center hole of the stand clamp large enough to pull the

cable(s) through.

Pole Height (H) Camera Angle (A) Distance (D)

≈160 cm / ≈5.25 ft ≈30° ≈63 cm / ≈2 ft

≈190 cm / ≈6.25 ft ≈45° ≈133 cm / ≈4.3 ft

Hardware Overview

Camera with

protective foam

USB cable

to camera

Pole

Screws used to adjust

stand height (x4)

Display holder

(optional - can be

mounted on any

side of the pole)

Stand cover

Mounting screws (x4)

Stand clamp

USB cable(s)

to PC

Leveling screws (x4)

Stand base

Camera clamp

Adjust Pole Height

Pole height (H) is measured from the top of the pole to the top of

the measurement area or scale.

1. Loosen the screws on each side of the pole

(4x) using an Allen wrench.

2. Slide the pole up to the desired height.

3. Tighten screws on each side of the pole to

secure the pole.

4. Pull the camera cable out of the bottom of

the pole until approximately 25 cm (10 in)

remain exposed at the top of the pole so it

can be attached to the camera later.

5. Cut the cable covers to the length needed to

cover the cable channels on the pole. Snap

into cable channels.

Note: Cut the cable cover for the back side of the

pole sightly shorter than the others so that

the camera cable can exit and be

connected to the camera.

Cable

covers

Route the Cables

By default the cables are routed out of the bottom of the stand.

To route the cables out of the side:

1. Pull up the stand cover - some resistance is normal.

2. Pull the cables up and through the side exit on the pole.

Cable exit

Install the AutoCube Camera

1. Angle the clamp on the top of the pole perpendicular to the

pole. Turn the knob to loosen the clamp.

2. Insert the ball of the camera into the clamp. Make sure the

camera is right side up (Honeywell logo on front right side

up). Adjust the camera to the correct angle (A) from the pole

(see Dimensions at the beginning of this document).

3. Turn the knob to tighten the clamp. Be sure it is tight

enough so that the camera will not move.

4. Attach the USB cable at the top of the pole to the camera.

Secure the cable to the camera by tightening the screws by

hand.

Note: Be sure the camera is horizontal to the measurement area

and aimed directly at the area.

Caution: DO NOT remove the protective foam during

installation.





Knob to tighten or

loosen clamp

Note: Keep the protective foam on the camera until installation is

finished.

Mount the Stand

Recommended 2 person operation.

1. Rotate the stand assembly upright on the mounting sur-

face. Align stand base to previously drilled holes.

Note: If cables exit through the bottom of the pole, pull them

through the mounting surface.

2. Place washers on the stand base then the mounting bolts

through the stand base and mounting surface. Thread into

the stand clamp placed under the mounting surface.

Autres manuels pour AUTOCUBE 8200

Table des matières

Autres manuels Honeywell Caméra de sécurité

Honeywell

Honeywell HC35WZ2R25 HC35WZ5R30 Manuel utilisateur

Honeywell

Honeywell HD3DS Manuel utilisateur

Honeywell

Honeywell IPCAM-WOC1 Manuel utilisateur

Honeywell

Honeywell HCC10 Manuel utilisateur

Honeywell

Honeywell CASD120PTW Manuel utilisateur

Honeywell

Honeywell HCC474M Manuel utilisateur

Honeywell

Honeywell PrimaView HCGC48 Manuel utilisateur

Honeywell

Honeywell HBD92SX Manuel utilisateur

Honeywell

Honeywell HD5 Series Manuel utilisateur

Honeywell

Honeywell HD40 Series Manuel utilisateur

Honeywell

Honeywell HD3VC4SAX Manuel utilisateur

Honeywell

Honeywell HD14 Manuel utilisateur

Honeywell

Honeywell HD61 Series Manuel utilisateur

Honeywell

Honeywell ACUIX Manuel de l'opérateur

Honeywell

Honeywell HC60WB4R2 Manuel utilisateur

Honeywell

Honeywell HD3USX Manuel utilisateur

Honeywell

Honeywell HD4 EQUIP Series Manuel utilisateur

Honeywell

Honeywell equIP H2S1P6X Manuel utilisateur

Honeywell

Honeywell HCD484E Manuel utilisateur

Honeywell

Honeywell HED2PER3 Manuel utilisateur

Honeywell

Honeywell HB273H Manuel utilisateur

Honeywell

Honeywell HCC334L Manuel utilisateur

Honeywell

Honeywell UltraDome KD6i Manuel utilisateur

Honeywell

Honeywell HD73 Series Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur