Honeywell SeqLED E SET-30 Manuel utilisateur

SeqLED E

70mm

160mm

70mm

26mm

Dimensional Drawings:

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Installation:

Step 2: Unfasten the four retaining screws without removing them and remove the diffusor.

Step 3: Set the module address. For more information about module settings see the next

page.

Step 1: Unfasten the front screw and remove the cover.

Weight:

Technical description

Part no.:

Lumen output:

-30 to 60 C

Up to 95%

Produced in accordance with:

Ambient Temperature Range:

Maximum Power Consumption:

Operation Voltage: 220-240V AC/DC, 50-60 Hz

280 lm

500 gr

3.8W / 4.2VA

138005.S30

SeqLED E SET-30 230V

Relative Humidity:

Technical lifetime (light source): > 100000 hours

IP65

Degress of cover protection:

EN 60598-1, EN 60598-2-22, EN 55015

EN 61547, EN 61000-3-2, EN 61000-3-3

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

PE N L

washer

rubber

o-ring

PE N L

MOUNTING METHODS

Surface mounting on the wall

INSTALLATION

Step 1: Unfasten the front screw and remove the cover. Next, unfasten the four retaining screws without

removing them and remove the diffusor.

Step 3: Use a drill with a 3,5mm bit to open the 4 mounting holes located in the plastic base. Place the

luminaire on the desired mounting location and mark and drill these 4 holes. Fit the supplied 4

plastic mounting plugs to these drilled holes on the mounting location.

Step 2: Install the supplied cable gasket from the inside of the plastic base.

Step 4: Open a cable entry cutout hole on the plastic base and install the supplied cable gasket. Make a

hole in the center into the desired gasket by using a small screwdriver and pass the round cable

through the gasket. Connect the main cables to the respective terminal block: N for neutral, L for

live wire and PE for ground wire. Install the included tie (if needed) to fasten securely the power

cables. Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type

2x1mm² or any other type, at least equal to it's mechanical and electrical properties). ATTENTION!!

The cable must not be deformed in any way (This requirement is important to ensure the IP rating).

Step 6: Re-install the diffusor, fasten the four retaining screws, refit the cover and fasten the screw that

was removed in step 1.

Step 5: Mount the base to the desired location by using the supplied screws, washers and o-rings in

each mounting hole.

At the end of their useful life the packaging and product

should be disposed of via a suitable recycling centre.

Do not dispose of with your normal household waste.

Do not burn.

The light source contained in this luminary shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

MODULE FOR SINGLE LAMP SELECTION AND MONITORING

Switching of one selected light in the electric circuit

SET010 select

DIP-switch 1

ON for non-maintained mode (Default)

DIP-switch 2

OFF for lighting address 1-16 (Default)

ON for lighting address 17-32

Indicator LED

Rotary coding switch

for setting the exact lamp adress DIP-switch 3 (OFF)

Attention!

Connect L and N correctly!

Exchanging L and N causes malfunction.

Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the

outside.

The module is already prepared for administering a total of 32 lighting addresses.

Function

By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the

lamp connected to it is ready for use or faulty.

Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.

The address range 17 to 32 can be selected by setting DIP switch 2 to ON.

Settings

(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)

Technical description

Cross section:

Temperature:

Dimensions (L x W x H in mm) 78 x 30 x 20

Max: 1.5mm

-30°C up to +60°C, T =+75°C

cmax

SET010 select

Prewired

Ce manuel convient aux modèles suivants

Autres manuels Honeywell Relais

Honeywell

Honeywell Farenhyt Series Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell R132A Guide de démarrage rapide

Honeywell

Honeywell NOTIFIER FW-RM Manuel utilisateur

Honeywell

Honeywell Aquastat L8148A Manuel d'utilisation

Honeywell

Honeywell R841C-E Manuel utilisateur

Honeywell

Honeywell ADEMCO 5800RL Instructions de montage

Honeywell

Honeywell HPSR101 Manuel utilisateur

Honeywell

Honeywell TRIPLEAQUASTAT L8151A Manuel utilisateur

Honeywell

Honeywell Aquastat L8148A Manuel utilisateur

Honeywell

Honeywell AQUASTAT L8124A Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell TRADELINE R182J Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell BDR91 Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell NOTIFIER FRM-1 Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell 301RW Manuel utilisateur

Honeywell

Honeywell RA889A Manuel utilisateur

Honeywell

Honeywell R182J Manuel utilisateur

Honeywell

Honeywell TRADELINE R8184G Manuel utilisateur

Honeywell

Honeywell 7800 SERIES RM7895A Manuel d'utilisation

Honeywell

Honeywell Silent Knight SK-Relay Manuel utilisateur

Manuels Relais populaires d'autres marques

Shelly

Shelly Pro Series Manuel utilisateur

GE MVAX 11 Manuel utilisateur

ABB

ABB RELION REF615R Manuel utilisateur

Pilz

Pilz PNOZ X10 Manuel du propriétaire

ABB

ABB SPAJ 142 C Manuel de la liste des pièces

Kemo Electronic

Kemo Electronic B197 Manuel utilisateur

Seg

Seg MRM3 Manuel utilisateur

Basler

Basler BE1-700C Manuel utilisateur

CD Automation

CD Automation REVEX 2PH 280A Manuel utilisateur

Ruelco

Ruelco 1S04 Manuel utilisateur

Basler

Basler V3E Z1P B2C1F Manuel utilisateur

Doepke

Doepke Dupline DSM 2 Manuel utilisateur

Siemens

Siemens SIRIUS 3RT1966-4D Manuel utilisateur

GE DGP Manuel utilisateur

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Manuel utilisateur

Siemens

Siemens SIPROTEC 4 Manuel utilisateur

Siemens

Siemens BD2-AK03X/FS Series Manuel utilisateur

Leuze

Leuze MSI-SR5B Manuel utilisateur