Honeywell 8732001 Instructions d'utilisation d'origine
Page 1
Models 8732001, 8732101, 8732301, 8732401
Read this manual carefully before installing and operating!
Installation & Operation Guide
Electronic Entry Lock with Knob
ENGLISH
Index
INSTALLATION INSTRUCTIONS
Package Contents / Tools Required...........................................................Page 1
Prepare Door and Jamb...............................................................................Page 2
Adjusting Latch / Installing Latch...............................................................Page 3
Installing Exterior Assembly........................................................................Page 4
Installing Interior Assembly........................................................................Page 5-6
OPERATION INSTRUCTIONS
Exterior Assembly Overview......................................................................Page 7
Locking and Unlocking / Changing Programming Code /
Adding User Codes......................................................................................Page 8
Deleting User Codes / Automatic Lock Function /
Temporarily Disable Auto Lock..................................................................Page 9
VacationMode/SecureLock-outPeriod/SoundONandO
Restore Factory Settings / Low Battery Warning.....................................Page 10
Consumer Friendly Message Guide / Installation Trouble Shooting......Page 11
Consumer Assistance.................................................................................Page 12
Programming Record..................................................................................Page 13-14
Template.......................................................................................................Page 15
Limited Warranty.........................................................................................Page 17
Page 1
INSTALLATION INSTRUCTIONS
Package Contents
Tools Required
Tools Required for Installation
on Pre-drilled Doors:
• PhillipsScrewdriver
Tools Required for Installation
on Doors That Require Drilling:
• Drill
• TapeMeasure
• Pencil
• 2-1/8”(54mm)DrillHoleSaw
• 1”(25mm)Drill
•1/16”(2mm)Drill
• Chisel
• Hammer
• PhillipsScrewdriver
DONOTRETURNTOSTORE!Ifanypartsaremissingordamaged,
pleasecallCustomerServicetollfreeat1-800-860-1677Ext.1801(M-F8am–5pmPST)
Strike Plate
Latch(Adjustable)
2-3/8”(60mm)to2-3/4”(70mm)
5/16”(8mm)Screws-2ea.
3/4”(19mm)Screws-5ea.
InteriorAssembly Mounting Plate
ExteriorAssembly
Entrykeys(2ea.)
7/8”(22mm)Screws-2ea.
1”(25mm)Screw-1ea.
Page 2
NOTE: For installation on doors with pre-drilled holes skip to 4e.
1. TEMPLATE
a.Cutouttemplateprintedonpage15ofthisManual
(Figure1a).
b. Foldtemplateandplaceondoor36”(915mm)from
thegroundasmarked(Figure1b).
2. MARK THE DOOR FOR DRILLING
b. Mark center hole on door edge through guide on
templatefor1”(25mm)latchbolt(Figure2a).
a. Mark center hole on door face through guide on
templatefor2-3/8”(60mm)or2-3/4”(70mm)
backset(Figure2b).
3. DRILL AND CHISEL DOOR
a.Drill2-1/8”(54mm)holethroughdoorfaceasmarked
forlockset(Figure3a).
b.Drill1”(25mm)holeincenterofdooredgefor
Latch(Figure3b).
c. Insert Latch in hole keeping it parallel to
faceofdoor.MarkoutlineandremoveLatch
(Figure3c).
d.Chisel1/8”(3mm)deeporuntillatchfaceisush
withdooredge(Figure3d).
4. MARK AND DRILL DOOR JAMB
a. MarkcenterholeonedgeofjambevenwiththecenteroftheLatchBoltondoor
edge.(Figure4a).
b.Drill1”(25mm)hole1-3/16”(30mm)deepindoorjamboncentermark
(Figure4b).
c.OutlineoutsideedgesofStrikePlate(Figure4c).
d.Chisel1/8”(3mm)deepforStrikePlateoruntilush(Figure4d).
e.InstallStrikePlateusingtwo3/4”(19mm)screwsprovided(Figure4e).
PREPAREDOORANDJAMB
Figure4a Figure4b Figure4c Figure4e
Figure4d
NOTE: For Drive in Latch, drill hole size indicated on template and press
untilitisushwithdooredge.
Figure1a
Figure2a Figure2b
Figure3a
Figure3c
Figure1b
Figure3b
Figure3d
Page 3
5. INSTALLING THE LATCH (need phillips head screwdriver)
a.Makesurethefaceplatesitsushwiththedoor.Donotforce
thelatchintothemortiseush.Chiseloutexcessmaterialif
necessaryforausht(Figure5a).
b.Usingtwo3/4”(19mm).screwsprovided,screwthelatchintothe
doorwithahandheldscrewdriver.DONOTOVERTIGHTEN
(Figure5b).
ADJUSTINGLATCH
NOTE: Latch is shipped with the backset set at 2-3/8” (60mm)
Measurethebackset(backsetisdistancebetweenedgeofthedoorandthe
centerofLock).
TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET
TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET
2-3/8"(60mm )
PULL
2-3/4"(70mm)
PUSH
NOTE: Curved part of Latch always faces
curved portion of Strike Plate
INSTALLINGLATCH
Figure5a
Figure5b
Page 4
NOTE: Tailpiece must be
positioned vertically
INSTALLINGEXTERIORASSEMBLY
7. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR
a.Fromthesidemarked“Thissideagainstdoor”,
route the Control Wire through the rectangular
slotintheMountingPlate(Figure7a).
b.PlaceMountingPlateagainstdoorwithtailpiecepassing
throughthecenterholeinthethreeholeset(Figure7b).
c.SecuretheMountingPlatetotheExteriorAssemblyusing
two7/8”(22mm)Screws(Figure7c).
d.HandtightenwithaPhillipsScrewdriverleavingloosely
connected(Figure7d).
e.CheckthattheRubberGasketisproperlyalignedandcorrectasnecessary(Figure7e).
f.Checkverticalalignmentofthelock(Figure7f).
g.TightensecurelywithahandheldPhillipsScrewdriver.DO NOT OVER TIGHTEN
8. OPTIONAL INSTALLATION
a.Usinga1/16”(2mm)drillbit,drillapilotholeinyourdoor
usingtheMountingPlateupperholeasaguide(Figure8a).
b. Insert one 3/4”(19mm)screwandtighten.
Mounting Plate
3/4”(19mm)screw
(OptionalInstallation)
7/8”(22mm)screws
Control Wire
Figure8a
Figure7a-7f
NOTE: Rotate knob to ensure the latch is opening and closing easily.
6. INSTALLING THE EXTERIOR ASSEMBLY
Note: WorkwiththeDoorOpenforeasyaccess.Toaccessthemountingplate,unpack
theInteriorAssemblyandremovethebatterycoverbyslidingthecoverupward.Locate
thescrewsholdingtheMountingPlatetotheInteriorAssembly.Removethescrewsto
releasetheMountingPlatefromtheInteriorAssembly.
a.UnpacktheExteriorAssembly.Usecaretonotscratchthegreencircuitboard
during handling and installation.
b.CheckthattheRubberGasketisproperlyseatedontheExteriorAssembly
(Figure6a-b).
c.InserttheExteriorAssemblyontothedoorwiththetailpiecegoingthroughthe
Latch spindle in the VERTICAL POSITION. Route the Control Wire through
thedoorovertheLatch(Figure6c).
Rubber
Gasket
Control
Wire
Tailpiece
(Vertical)
Latch
Hole
Figure6a-b Figure6c
Page5
INSTALLINGINTERIORASSEMBLY
9. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY
a.UsecaretoattachtheControlWiremaleplugtotheInteriorAssemblyfemale
socketconnector(Figure9a).
b.DonotforcetheControlWiremaleplugintotheInteriorAssemblyfemale
socketconnector(Figure9b).
c.TheControlWiremaleplughastwoalignmenttabsonthesmoothsideofthe
plugwhichisthetopoftheplug(Figure9c).
d.TheControlWiremaleplugisinsertedwiththesmoothsideupintotheInterior
Assemblyfemalesocketconnector(Figure9d).
10. ATTACH THE INTERIOR ASSEMBLY TO DOOR
a.PositiontheInteriorAssemblyoverthetailpieceandpushtheInteriorAssembly
againstthedoor(Figure10a).
b.Usingtwo5/16”(8mm)screws and one 1”(25mm)screw, attach
theInteriorAssemblytotheMountingPlate.DO NOT OVER TIGHTEN SCREWS
(Figure10b).
5/16”(8mm)screws
1”(25mm)screw
NOTE: Lock and unlock using Interior Knob to see if the
latch is opening and closing easily.
Figure10a-b
Figure9a-d
Interior Wire
Connector Plug
Page6
11. Installing Batteries
a.Insert4AAhighqualityAlkalinebatteriesintotheBatteryCompartmentinthe
directionnoted+/-ontheCompartment.TheLockwillbeep2times,thekeypad
willilluminateblue,andtheHoneywellbuttonwillashgreentwicetosignifythat
ithasreceivedpower(Figure11a).
b.SlidetheBatteryCoverdownintothetrackontheInteriorAssemblytocover
thebatteries(Figure11b).
12. Testing Lock
WiththeDoorOpen
a.TesttheLockusingtheInteriorKnob.TheLatchshouldmovesmoothly.
b.TestthelockusingtheKeypad.Tolockpressandthenpress“1234”
to unlock.
INSTALLINGINTERIORASSEMBLY(CONT.)
Override
AccessKey
Exterior Assembly
Interior Assembly
Interior
Knob
Battery
Cover
Light Indicator
Keypad
NOTE:DonottouchtheKeypaduntilthebluelightturnso.
Do not use rechargeable batteries or non-alkaline batteries.
Figure11a-b
INSTALLATION OVERVIEW
Strike Plate
BatteryCover
InteriorAssembly
Keys Exterior
Assembly
Rubber Gasket
Tailpiece
Mounting Plate
Latch
5/16”(8mm)screws
Optional
3/4”(19mm)screw
3/4”(19mm)screws
7/8”(22mm)screws
1”(25mm)Screw
Page 7
OPERATION INSTRUCTIONS
ExteriorAssemblyOverview
Indicator light
Green
•IndicatesSuccessfulProgrammingStep
•IndicatesUnlockingisSuccessful
Red
•IndicatesFailedProgrammingStep
•IndicatesLockingisSuccessful
Electronic lock requires (4) High Quality
AA Alkaline batteries. When all 4 batteries
are installed in the correct position, hear 2
beeps and the keypad will illuminate blue.
DO NOT TOUCH the keypad until the keypad
stops illuminating.
Lock-Usedtolockdoor
Clear -Usedtoclearwrongkeypadentries
Unlock-Usedtounlockdoor
Programming -Usedinprogrammingsteps
5 Seconds -Completealltheprogrammingstepsintheprogrammingmodewithin5seconds.
Clear -Usethekeytoclearentriesincaseawrongbuttonispushed.
Lock button
Unlockbutton
FactorySettings
The lock comes factory preset with a:
Please change the Programming
Code and the User Code
as soon as possible after installation
to insure security.
Programming code - 123456
User code - 1234
User ID - 01
ID
PC
PC
UC
UC
Batteries(notincluded)
Programming Symbols
Lock / Clear
Unlock / Programming
Programming Code
User Code (4-8 digits)
User ID (01-50, 2 digits)
ID
PC
UC
Programming Tips
Page 8
TO UNLOCK THE LOCK
UsingKeypad:EnteravalidUserCode(defaultcodeis1234)andpressandhear
1 beep and lights green.
TOLOCKTHELOCK
UsingKeypad:Pressandthenhear2beepsandlightsred.
CHANGE CURRENT OR PRESET PROGRAMING CODE
FactorydefaultProgrammingCode=123456,thisisthemasterpasswordfor
yourlock.Allprogrammingfunctionsrequirethiscode.Followthebelowsequenceto
changetheProgrammingCodetoyourcustom6digitcombination.
TO ADD A NEW USER CODE (you can add up to 50 new user codes)
TheUserCodemustbea4-8digitcombination.EachUserCodeisthenlinked
toaUserID(whichisanynumberbetween01-50)toidentifyanindividualUser
Code.(UserID1-9shouldbeenteredas01-09sotheyare2digits).
Hear 1 beep and Light Indicator illuminates green.
RecordNewandChangedCodesonProgrammingRecordlocatedonPage13.
Hear 1 beep and Light Indicator illuminates green.
NOTE:WhenaNEWUSERCODEisset,thedefaultfactorycode(1234)isdeleted
for safety.
RecordNewandChangedCodesonProgrammingRecordlocatedonPage13.
123456 08 56785678
Forexample:toaddtheUserID-08toUserCode-5678,enterthefollowing:
4newRe-enter
1Re-enter
LockingandUnlocking
Changing Programming Code
AddingUserCodes
ID
ID
ID
UC UC
UC UC
UC
PC
PC
PC PC
PC
PC
PC
Ce manuel convient aux modèles suivants
3
Table des matières
Langues :
Autres manuels Honeywell Verrouillage
