Honeywell E3Point E3DA Manuel utilisateur
E3Point®
User Manual
Standalone, Network, & Remote models
Gas Monitor
| Gas Detection
1998M0972 Rev 01
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual i
Symbol Denitions
Symbol Definitions
The following table lists the symbols used in this document to denote
certain conditions:
Symbol Definition
ATTENTION: Identifies information that requires special
consideration.
TIP: Identifies advice or hints for the user, often in terms
of performing a task.
REFERENCE _ INTERNAL: Identifies an additional source
of information within the bookset.
CAUTION
Indicates a situation which, if not avoided, may result in
equipment or work (data) on the system being damaged
or lost, or may result in the inability to properly operate
the process.
!
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
CAUTION: Symbol on the equipment refers the user to
the product manual for additional information. The symbol
appears next to required information in the manual.
!
WARNING: Indicates a potentially hazardous situation
which, if not avoided, can result in serious injury or death.
WARNING symbol on the equipment refers the user to
the product manual for additional information. The symbol
appears next to required information in the manual.
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual iii
IMPORTANT NOTICE
IMPORTANT NOTICE
System Validation Test or Commissioning of the gas detection system is
not complete until it is tested to verify that it is functioning according to
its design objectives or specifications.
Validation includes, but is not limited to:
•Verication tests of the functions of each component in the individual
system architecture.
•Verication that all inputs to the system result in the correct outputs.
•Verication that, where required, a back-up power supply system
is in place.
•Verication that all personnel who will be working with and/or
affected by the system have received proper instruction on use
and purpose.
www. .com information@itm.com1.800.561.8187
iv E3Point Gas Monitor Technical Manual
Table of Contents
Table of Contents
Symbol Definitions ...............................................................................i
IMPORTANT NOTICE.......................................................................... iii
Introduction..........................................................................................1
Restricted Materials Table for China RoHS..........................................1
Warnings and Cautions.......................................................................2
Installation............................................................................................4
Locating the Sensor............................................................................4
Installation Height ..................................................................5
Wall Mounting for Standalone/Network monitor .....................5
Mounting for Remote monitor .............................................................7
Duct Mounting....................................................................................8
Special Duct Mount Installation..............................................8
Wiring..................................................................................................10
Guidelines.........................................................................................10
Wiring Standalone monitor ..................................................10
Connecting a Remote monitor to the Standalone monitor....12
Wiring Network Monitors .....................................................12
Installation Test..................................................................................13
Standalone Model Operation ..........................................................14
Start-Up Procedure ..........................................................................14
Network Model Operation ...............................................................15
User Interface ...................................................................................16
Monitor Operation .............................................................................17
Using the Programming Menus.........................................................17
Main Menu Options ..........................................................................17
Password Menu ..................................................................18
Network Menu.....................................................................18
Display Menu.......................................................................19
Restore Menu......................................................................19
Temp Menu .........................................................................20
Set Zero Menu.....................................................................21
Set Span menu ...................................................................22
TestMode Menu...................................................................23
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual v
Table of Contents
Memory Menu .....................................................................23
Quit Menu ...........................................................................23
Model Specific Menu Options...........................................................24
Standalone Model Relay Menu ............................................24
Standalone Model Buzzer Menu..........................................25
Standalone Model Alarm Menu............................................25
Network Relay Menu ...........................................................27
Network Model Buzzer Menu ..............................................28
Network Model Alarm Menu ................................................29
Remote Sensor..................................................................................31
Description .......................................................................................31
Safety Information ...............................................................31
Specifications ....................................................................................32
General Technical Specifications.......................................................32
Detection Ranges and Alarm Levels..................................................33
Sensor Over Range ..........................................................................33
Periodic Inspection and Maintenance ...............................................35
Maintenance........................................................................35
Sensor Life Span.................................................................35
Troubleshooting.................................................................................36
Annex A - BACnet and Modbus Objects on E3Point Network.......39
BACnet Configuration.......................................................................39
BACnet Objects Descriptions ..............................................39
Modbus Registers Description..........................................................40
BACnet Protocol Implementation Conformance Statement.........40
Limited Warranty ...............................................................................45
Limited Warranty...............................................................................45
Re-Stocking Policy ...........................................................................45
Exclusions ........................................................................................45
Warranty Limitation and Exclusion ....................................................46
Disclaimer of Unstated Warranties ...................................................46
Limitation of Liability .........................................................................46
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual
Introduction
1
Introduction
E3Point derives its name from: Energy Management, Efficiency, and Economic
value in gas detection.
E3Point is an important part of toxic or combustible gas detection system that
combines a gas sensor (electrochemical or catalytic type), a control unit, and a set
of outputs (such as 4-20 mA current loop, buzzer and relays). The polycarbonate
housing is resistant to rust, dents and corrosion.
There are 3 monitor models in the E3Point family: Standalone, Remote and
Network. The Standalone monitor provides the full control unit, with a built
in sensor and is capable of accepting one additional Remote sensor. This
configuration allows the E3Point to detect two gases in two separate locations.
The E3Point Network platform supports different protocols over an RS-485 link,
such as Modbus or BacNet MS/TP master. It is well suited for commercial use in
parking garages and mechanical rooms. It is intended for connection to the 301-C
or AA96D series contollers.
Installation is both economical and efficient because it is achieved in 3 easy steps
(mounting, wiring and power-up). Units are shipped with a Quick Start Guide to
support proper installation.
Restricted Materials Table for China RoHS
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual
Warnings and Cautions
2
Warnings and Cautions
Warnings
•Power to the E3Point monitor must be off during installation and when
installing the sensor cartridge.
•The installer must be grounded for ESD protection while handling the PC
board (PCBA) and during installation of the monitor.
•Follow all local codes when installing the monitor.
•Operate, service, and use the monitor only as specified in the quick start
guide and this technical manual. Failure to do so may impair the protection
the monitor is designed to provide and may also void the warranty. The
manual is available on the Honeywell Analytics website. You may scan the
QR code below for easy access to product information:
•Calibration, set-up, and test modes are intended for use by trained personnel
and service engineers only. Access to these modes is passcode protected.
•Follow local and site procedures when working with this monitor. If applicable,
verify that the associated control panel is inhibited in order to prevent false
alarms during installation. The procedures in the quick start guide and the
product’s technical manual must be followed carefully and performed only
by trained personnel and service engineers.
•Use only accessories and parts meeting or exceeding Honeywell Analytics’
specifications.
•Some monitors require warm-up time. See the appropriate sections in this
technical manual for specific information.
•Ensure that the monitor screen is free of dirt and debris, and do not cover
or paint over the monitor screen.
•Do not expose the monitor to electrical shock and/or continuous mechanical
shock.
The warranty will be voided if the customer or any unauthorized service
personnel attempt to repair the monitor
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual
Warnings and Cautions
3
Cautions
•The E3Point monitor must be installed only by trained personnel and service
engineers in accordance with local codes.
•The safety of any system incorporating the E3Point monitor is the responsibility
of the assembler of the system.
•Protect the monitor from water, wash-down, and excessive humidity.
•To prevent electrical interference, keep the monitor and wire runs away from
mercury vapor lights, variable speed drives, and radio repeaters.
•Protect the monitor from physical damage (fork lifts, etc.).
•Do not mount the monitor over a door in a refrigerated area.
•For critical locations, more than one monitor should be installed in each room.
•Never mount the sensor flat on a ceiling.
•Never mount the sensor on a vibrating surface.
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual
Installation
4
Installation
!
WARNING: Some materials such as, but not limited to, tetraethyl lead,
silicones, some sulfur, phosphorus, and chlorinated compounds, may have a
poisoning effect resulting in a loss of sensitivity. Avoid installing the monitor
in areas where these materials may be present.
Locating the Sensor
Considerations in locating the monitor
Instalation Height:
•Fastest Possible Leak Detection – Mount the monitor near the
potential leak sources
- One monitor should be located in close proximity to each point where
an emission is likely to occur
- Indicated concentration may not be representative of personnel
exposure
- Easy access for the required calibration and maintenance could be
compromised
•Personnel Protection
– Mount the sensor at the installation heights shown in the table below
–Gas is detected where it is accumulated – which may not be detected
at the leak source.
Air Currents: If there are fans, wind, or other source of air movement, gases may
tend to rise or collect in certain areas of a facility. The local air currents should be
assessed to aid in selecting the sensor location. Air convection can often be more
important in determining gas concentration areas than factors of Vapor Density.
Gas Emission Sources: As a rule, at least one sensor should be located in close
proximity to each point where an emission is likely to occur.
!
CAUTION: Because each sensor can only “report” what it is
detected at the place it is installed at a specific moment, it
is very important that the sensor be located where leaks
are most likely to occur.
www. .com information@itm.com1.800.561.8187
E3Point Gas Monitor Technical Manual
Installation
5
Installation Height
Detected Gas Relative Density Installation Height
(air = 1)
CO Carbon monoxide 0.968 1–1.5 m (3–5 ft.) from floor
H2SHydrogen sulfide 1.19 30 cm (1 ft.) from floor
*NO2Nitrogen dioxide 1.58 (cold) 30 cm–1 m (1–3 ft.) from ceiling
O2Oxygen 1.43 1–1.5 m (3–5 ft.) from floor
COMB Most combustibles are heavier than air, with the exception of methane,
hydrogen, ethylene and acetylene. Sensors for gases that are heavier
than air should be installed approximately 30 cm (1 ft) from the floor. For
combustibles that are lighter than air, sensors should be installed 30 cm
(1 ft) from the ceiling, close to the potential leak source.
* May differ in certain applications. Hot NO2from exhaust systems is lighter than
ambient air.
Wall Mounting for Standalone/Network monitor
1. Verify that power to the monitor is off.
2. While properly grounded for ESD protection, remove the PCBA from the
monitor. It is attached by a single center screw. Carefully place the PCBA
in the enclosed antistatic envelope.
3. Drill two holes through the case and into the mounting surface;
horizontally if mounting on a vertical surface or vertically if mounting to a
standard electrical box as indicated below.
4 3/8 in (11.1 cm)
for mounting on
vertical survaces
3.28 in (8.3 cm)
for mounting on electrical boxes
www. .com information@itm.com1.800.561.8187
Table des matières
Autres manuels Honeywell Détecteur de gaz
Honeywell
Honeywell PHD6 Guide de référence
Honeywell
Honeywell Gamewell-FCI E3 Series Manuel utilisateur
Honeywell
Honeywell BW GasAlertMicroClip XT Manuel utilisateur
Honeywell
Honeywell SEARCHZONE SONIK SZSK-SMG Series Manuel utilisateur
Honeywell
Honeywell BW Technologies GasAlert MicroClip XT Manuel utilisateur
Honeywell
Honeywell 201T Manuel utilisateur
Honeywell
Honeywell Sensepoint XRL Manuel utilisateur
Honeywell
Honeywell Apex Note de version
Honeywell
Honeywell SEARCHLINE EXCEL PLUS Guide de l'utilisateur
Honeywell
Honeywell Rae Systems MeshGuard Guide de référence rapide
Honeywell
Honeywell Notifier NCO-10 Manuel utilisateur
Honeywell
Honeywell BW Ultra Manuel utilisateur
Honeywell
Honeywell Touchpoint Plus Note de version
Honeywell
Honeywell Signalpoint Pro Manuel utilisateur
Honeywell
Honeywell BW Solo Manuel utilisateur
Honeywell
Honeywell BW Icon Manuel utilisateur
Honeywell
Honeywell Midas-M Manuel utilisateur
Honeywell
Honeywell Touchpoint 4 Manuel utilisateur
Honeywell
Honeywell BW Clip Real Time Manuel utilisateur
Honeywell
Honeywell BW Ultra Manuel utilisateur
Manuels Détecteur de gaz populaires d'autres marques
Macurco
Macurco GD-6 Manuel utilisateur
Evikon
Evikon E2632 Manuel utilisateur
Critical Environment Technologies
Critical Environment Technologies CGAS-A Series Manuel utilisateur
MSA
MSA altair 5 Manuel utilisateur
DOD Technologies
DOD Technologies ChemLogic CL96 Manuel utilisateur
DEGA
DEGA NS III LCD Series Manuel utilisateur
