Honeywell UMC800 Manuel utilisateur

Form 51-52-33-100 Page 1 of 3

UMC 800

Operator Interface Disk Drive Assembly

Replacement Instruction

Disk Drive Assembly Kit (Part Number 51404557-501)

Document Number Form: 51-52-33-100

Effective: 6/98

Supersedes: None

Summary Enclosed is a new disk drive assembly for the Operator Interface (OI) of

your UMC 800 Controller. Use the following procedure to install it.

WARNING Never access components inside the operator interface with

power applied.

CAUTION This equipment contains devices that can be damaged by

electrostatic discharge. It is imperative that assemblies containing static-

sensitive devices be carried in conductive plastic bags. When adjusting or

performing any work on such assemblies, grounded work stations and

wrist straps must be used.

Tools Needed You will need a small Phillips-head screwdriver to perform this procedure.

Component Location Refer to Figure 1 for the location of the disk drive assembly and Table 1

for the installation procedure.

OI Housing Disk Drive

Assembly

Screws

(2 places)

J10

J3A

J3B

OI Housing

(Front Panel

Removed)

Figure 1 – Location of Disk Drive Assembly

Kit Instruction, continued

Page 2 of 3 Form 51-52-33-100

Replacement Follow the procedure in Table 1 to upgrade your operator interface to add

Procedure the floppy disk drive feature or to replace the disk drive assembly in the

OI.

Table 1 – OI Disk Drive Assembly Replacement. (Refer to Figure 1.)

Step Action

1Open the door on the righthand side of the OI unit. If OI is equipped with a disk drive,

press the button on the front to eject the diskette from the disk drive.

2Remove power from the operator interface by removing the cable from the back of the unit.

3Remove the front cover by removing two screws at the right, next to the disk drive.

See figure.

ALARM

ESC

1 5

⇐Screw

4Angle the right side of the front panel away from the unit and release it from the hinge at

the left.

5Unplug the following cables from connectors on the CPU board and remove the front panel.

a) OI display cable from J1.

b) Keypad cable from J2.

c) Twisted pair cable from J9.

6Remove two screws securing the disk drive assembly at the top and bottom of the OI

housing.

7Unplug the twisted pair cable from J3B of the CPU board. Carefully slide the disk drive

out of the housing.

8Unplug the following cables from the CPU board and remove the disk drive from the

housing:

a) The ribbon cable from J10.

b) The four-pin connector cable from J6.

Procedure continued on next page

Kit Instruction, continued

Form 51-52-33-100 Page 3 of 3

Table 1 – OI Disk Drive Assembly Replacement. (Refer to Figure 1.), continued

Step Action

9Install the ribbon cable and the power cable (supplied with kit) on replacement disk drive.

10 Plug in the disk drive ribbon cable to J10 on the CPU board.

Plug in the disk drive power cable to J6 (four-pin connector).

11 Carefully slide the disk drive into the OI housing. Plug in the twisted pair cable to J3B on

the CPU board.

12 Secure the disk drive to the housing at top and bottom with two screws.

13 Plug in the cables from the front panel to the following connectors on the CPU board:

a) Twisted pair cable to J9.

b) Flat ribbon cable to J2.

c) Gray ribbon cable to J1.

14 Reattach the front panel to the OI housing by hooking the tabs on the left side of the front

panel and securing it on the right side with two screws.

15 Plug in the DISPLAY cable from the controller into the OI connector at the rear of the

housing.

16 Power up the controller.

Look for start up screen.

Access the SELF-TESTS* screen under the Unit Menu.

Perform the KEYBOARD TEST and DISPLAY TEST to verify OI operation.

Open door on right side of OI front panel. Verify that display message reads “BEZEL

OPEN”.

17 Perform the DISK READ/WRITE TEST to verify OI operation.

* See UMC 800 Operator Interface User Guide, Document Number 51-52-25-62 for

more information on OI self tests and OI operation.

Autres manuels pour UMC800

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell T775B Guide d'installation

Honeywell

Honeywell M847D Manuel utilisateur

Honeywell

Honeywell 6200 Series Manuel d'instructions

Honeywell

Honeywell R7284B Manuel utilisateur

Honeywell

Honeywell HON 5020 Manuel utilisateur

Honeywell

Honeywell 9782 Series Manuel utilisateur

Honeywell

Honeywell T775R 2000 Series Manuel utilisateur

Honeywell

Honeywell UDC3500 Instructions d'installation et d'utilisation

Honeywell

Honeywell MN7220 Manuel d'utilisation

Honeywell

Honeywell ML8824-BV Series Manuel utilisateur

Honeywell

Honeywell touchpoint Pro Manuel utilisateur

Honeywell

Honeywell 1000 Series Manuel utilisateur

Honeywell

Honeywell RA890G Manuel utilisateur

Honeywell

Honeywell UDC3300 Manuel utilisateur

Honeywell

Honeywell T775 Series Guide de l'utilisateur

Honeywell

Honeywell HCE 60 Manuel du propriétaire

Honeywell

Honeywell SLATE Series Manuel utilisateur

Honeywell

Honeywell HR 80 Manuel utilisateur

Honeywell

Honeywell Excel 10 Manuel utilisateur

Honeywell

Honeywell DC1000 SERIES Manuel utilisateur

Honeywell

Honeywell MN6105VAV Manuel utilisateur

Honeywell

Honeywell Air Alert 96d Manuel utilisateur

Honeywell

Honeywell R7426A Manuel utilisateur

Honeywell

Honeywell S8600B Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur