Honeywell PRO 2000 Series Manuel du propriétaire



To program the controller, perform the following procedures in the order listed:

   

Fig. 1 Program Menu

Press the MENU button, then select PROGRAM and press the button to view the

program menu.

  !

Fig. 2

1. From the menu, use the and buttons to highlight RELAY 1.

2. Press the button to select RELAY 1 to view the parameters. Fig. 2 shows

RELAY 1.

 "#

Fig. Program - Setpoint

1. From the menu, use the and buttons to highlight SETPOINT.

2. Press the button to display the setpoint value.

3. Use the and buttons to increase/decrease the desired setpoint

temperature.

Set the temperature to 45° F.

4. Press the button to accept the setpoint temperature and display the next

option.

Honeywell Series 2000

 $"%%&#"'"#(

Fig. Program – Differential

1. From the menu, use the and buttons to highlight DIFFERNTL.

2. Press the button to display the differential value.

3. Use the and buttons to increase/decrease the desired value.

Set the value to 3° F.

4. Press the button to accept the value and display the next option.

 )#&

Fig. Program – Sensor

1. From the menu, use the and buttons to highlight SENSOR.

2. Press the button to display the sensor selections.

3. Use the and buttons to select Sensor A or B.

Select sensor A.

4. Press the button to accept the highlighted sensor and display the next option.

 *+,'

Fig. Program Heat/Cool

1. From the menu, use the and buttons to highlight HEAT/COOL (Default:

HEAT).

2. Press the button to display the heat and cool selections.

3. Use the and buttons to select Heat or Cool.

Select COOL.

4. Press the button to accept the highlighted selection and display the next

option.

____________________________________________________________________



    

 - 

Fig. Program – Exit

Press the EXITbutton to finish the programming for Relay 1.

Press the HOME button to leave programming mode and return to the home screen.

This completes the programming procedure for Cooling Only System.



 



To program the controller for time delay, perform the following procedures in the

order listed:

  



To access the Setup menu, press and hold the MENU button for five seconds. See

Fig. 1.

! 

When you are working with the menus, use the:

•Left arrow button ( ) to scroll backward through the menus

•Right arrow button () to select the highlighted menu item and display

its content

•Up and Down arrow buttons (and ) to scroll up and down through a

list of items or to increase or decrease the value of a displayed parameter

NOTE: If you press the HOME

button or there is no keypad activity for four

Minutes, you exit Program mode and return to the home screen.

If you press the MENU button, you exit and return to the menu.









  

To go from Setup menu screen as shown in Fig. 1 to Min Off screen shown in Fig. 2,

follow the steps as listed below:

1. From the Setup menu (Fig. 1), use the Down arrow button () to highlight

OUTPUTS.

2. Press Right arrow button () to display the Outputs menu.

3. Press the Down arrow button () to highlight OPTIONS.

4. Press Right arrow button () to display the Options menu.

5. Press the Down arrow button () to highlight MIN OFF.

6. Press Right arrow button () to display the Min Off screen (Fig. 2).

" #$%&&'(

This is the minimum number of seconds of “off time” for all relays.

Use the Up and Down arrow buttons (and ) to increase/decrease the desired

number of seconds from 0 to 990 in 10 second increments.

Default: 0 (zero)

Range: 0 to 990 seconds

Aqua Air factory setting: 20 seconds

)*+

After entering the desired number of seconds, press HOME button to accept the seconds

and finish the programming process. The display should show Home screen.

_____________________________________________________________________

Autres manuels pour PRO 2000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell Aquastat L4006 Manuel utilisateur

Honeywell

Honeywell PP904A Manuel utilisateur

Honeywell

Honeywell CentraLine LYNX LON CLLYUL1012S Manuel d'utilisation

Honeywell

Honeywell INCOMM L510 Manuel utilisateur

Honeywell

Honeywell V8200 Manuel utilisateur

Honeywell

Honeywell TRADELINE SmartValve SV9602P Manuel utilisateur

Honeywell

Honeywell Ex-Or MLS Manuel d'installation et d'exploitation

Honeywell

Honeywell ML6421 Manuel d'utilisation

Honeywell

Honeywell L4188 Manuel utilisateur

Honeywell

Honeywell MIWI350 Mode d'emploi

Honeywell

Honeywell HA40 Manuel utilisateur

Honeywell

Honeywell Centra Line HAWK 8000 Manuel d'installation et d'exploitation

Honeywell

Honeywell T775U Series Manuel utilisateur

Honeywell

Honeywell Excel 100C Manuel utilisateur

Honeywell

Honeywell ML6874 Manuel d'utilisation

Honeywell

Honeywell HC900 Manuel utilisateur

Honeywell

Honeywell Excel 10 Manuel utilisateur

Honeywell

Honeywell Aquasat L7224 A Aquasat L7224 C Manuel utilisateur

Honeywell

Honeywell HR 80 Manuel utilisateur

Honeywell

Honeywell S9360B Manuel utilisateur

Honeywell

Honeywell Satronic DVI 980 Manuel utilisateur

Honeywell

Honeywell DCP 250 Guide d'installation

Honeywell

Honeywell ML7984B Manuel utilisateur

Honeywell

Honeywell ML7295E Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur