Honeywell HVC0001 Manuel utilisateur

Owner’s Guide

Guide du propriétaire

Guía del usuario

HVC0001 / HVC0002

Programmable Bath Fan Control

Contrôleur de ventilateur programmable

Controlador de ventilador programable

HVC0001/HVC0002

ENGLISH

Quick reference

The LED illuminates

when the bath fan is On.

Press the Main Button to turn the

bath fan On or Off. (Press for 3

seconds to enter the setup menus.)

Press either button to place in

Countdown Mode. Then press the

left button to decrease the

countdown time or the right button

to increase the time.

Setup menu

Clock

The bath fan is On The bath fan is Off

Programmable modes

Countdown time

If the controller is also used to control

lights, pull out this safety tab before

replacing the light bulb. Push back in

after the light bulb is replaced.

Countdown Mode

(see page 17)

HVC0001/HVC0002

ENGLISH

‹Cut power at the main electrical panel to avoid electric shock.

›Remove the existing switch if applicable.

ﬁInstall the bath fan controller.

ﬂApply power at the circuit breaker.

4-wire installation

120

VAC

black

white

black

white black (LINE)

black (LOAD)

green (GND)

For installation in wet locations, protect the circuit

with a ground fault circuit interrupter (GFCI).

HVC0001/HVC0002

ENGLISH

Set the time and date

Set Hour Set Minutes

Set Year Set Month Set Day

Select 24H or 12H

The time flashes on the screen when it is

not yet set or after a power outage of

more than 4 hours. To set the clock,

press the main button for 3 seconds to

display the setup menu and proceed as

shown.

Press the main button for 3 seconds at

any time (or do not press any button for

60 seconds) to save any changes you

have made and exit the setup menu.

HVC0001/HVC0002

ENGLISH

When Automatic Daylight Savings Time changeover is enabled (DST On), the controller automatically

switches to daylight savings time (summer time) at 2:00 am on the second Sunday of March and back to

standard time (winter time) at 2:00 am on the first Sunday of November. This function is enabled by

default.

Set the Automatic Daylight Savings Time Changeover

Set Daylight

Saving Time

(2 times) (2 times)

To set the Automatic

Daylight Savings Time

Changeover, press the

main button for 3

seconds to display the

setup menu and

proceed as shown:

Press the main but-

ton for 3 seconds at

any time (or do not

press any button for

60 seconds) to save

any changes you

have made and exit

the setup menu.

HVC0001/HVC0002

ENGLISH

To place

the controller

in Ventilation Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On during the idle period, the fan will remain On until the

beginning of the next idle period or until you press the main button again.

Ventilation Mode (cont’d)

Select

Ventilation Mode

Normal Display

(3 sec.) (3 sec.)

HVC0001/HVC0002

ENGLISH

To place the controller in Customized Cycle Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On during the idle period, the fan will remain On until the

beginning of the next idle period or until you press the main button again.

Customized Cycle Mode (cont’d)

Select Customized

Cycle Mode

Customized Cycle Mode

Normal Display

(3 sec.) (3 sec.)

HVC0001/HVC0002

ENGLISH

To place the controller in Daily On/Off Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On, it will remain On until the programmed Off time or until you

press the main button again.

Daily On/Off Mode (cont’d)

Select Daily

On/Off Mode

Daily On/Off Mode

Normal Display

(3 sec.) (3 sec.)

HVC0001/HVC0002

ENGLISH

Place the controller in Countdown Mode to run the fan for 10-60 minutes. The fan turns On when the

controller is in this mode. At the end of the countdown time, the controller returns to its programmed mode

and the fan turns Off. (NOTE: The fan might stay On if the controller has been set to turn the fan On at

that given time in the programmed mode.)

You can cancel the Countdown Mode and return to the programmed mode at any time by pressing the

main button.

To place the controller in Countdown Mode,

proceed as shown:

Countdown Mode

After

5 sec.

Set Countdown

Time (minutes) *

Countdown Mode

is activated

At end of Countdown Mode

Normal Display _+

* Press the left or right button once

to use the same countdown time

as the one used the last time.

Press the left (-) or right (+) button

more than once to decrease or

increase the countdown time (in

increments of 5 minutes).

Owner’s Guide 400-305-000-EFS

ENGLISH

HVC0001:white

HVC0002: biscuit

Voltage: 120 VAC - 15%, + 10%

Frequency: 60 Hz ± 5%

Minimum Load: 0.1 A (12 W)

Maximum Load: 2.5 A (300 W)

Minimum Power Factor:0.60

Operating Temperature Range: -15°C to 50°C (5°F to 122°F)

Storage Temperature Range: -40°C to 60°C (-40°F to 140°F)

Product Specifications

Autres manuels pour HVC0001

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell UDC2800 Manuel utilisateur

Honeywell

Honeywell S05 Series Manuel utilisateur

Honeywell

Honeywell S7014A Series Manuel utilisateur

Honeywell

Honeywell T775L Series Manuel utilisateur

Honeywell

Honeywell CENTRA LINE EAGLEHAWK Manuel d'installation et d'exploitation

Honeywell

Honeywell PRO3200 Manuel de l'opérateur

Honeywell

Honeywell Touchpoint Plus Manuel utilisateur

Honeywell

Honeywell Spyder 7 Manuel utilisateur

Honeywell

Honeywell T775P 2000 Series Manuel utilisateur

Honeywell

Honeywell BC-200 Instructions de montage

Honeywell

Honeywell M7410E Manuel d'utilisation

Honeywell

Honeywell ScanDome HTX-5000 Manuel utilisateur

Honeywell

Honeywell TRADELINE SV9501 Manuel utilisateur

Honeywell

Honeywell DeltaNet R7515A Manuel utilisateur

Honeywell

Honeywell DBC2000 Series Manuel utilisateur

Honeywell

Honeywell VR8104 Manuel utilisateur

Honeywell

Honeywell CentraLine LYNX BACnet CLLYUB1012S Manuel d'utilisation

Honeywell

Honeywell PCR-310 Manuel utilisateur

Honeywell

Honeywell VK41 V Series Manuel utilisateur

Honeywell

Honeywell UDC3300 Manuel utilisateur

Honeywell

Honeywell HR 40 Manuel utilisateur

Honeywell

Honeywell LP1501 Manuel de l'opérateur

Honeywell

Honeywell McDonald's HEMS II Manuel utilisateur

Honeywell

Honeywell T775A Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur