Honeywell CD3200 Manuel utilisateur

EN1I-6312

USER’S MANUAL CD3200

THYRISTOR UNIT

Up To 110A

Rev. 12/2004

User’s Manual ver. 2.0 CD3200 up to110A Honeywell

1 www.honeywell.com/imc

CD3200 Thyristor Unit up to 110A

Index:

1. Glossary 5

1.1 Terminology 5

1.2 Input signal 5

1.3 Power feed back 5

1.4 What is a thyristor unit 5

2. Technical specifications 6

2.1 General Features: 6

2.2 Input features 7

2.3 Output features 7

2.4 Derating curve 7

3. Ordering information 8

4. Installation and wiring information 9

4.1 Identification of the unit 9

4.2 Installation 9

4.3 Dimensions 10

4.4 Dimension CT (Heater Break HB) 10

4.5 Fixing holes 11

5. Wiring Instructions 12

5.2 Cabling detail 13

5.3 Wiring connection 15

5.4 LED Status Table 17

6. Start up 18

6.1 To remove the board 19

6.2 Auxiliary supply 20

6.3 Analog input 21

6.4 Heater Break Alarm 23

6.5 Current Limit Tuning 28

7. Thyristor firing mode 29

7.1 Phase Angle + Current Limit (PA) 29

7.2 Configurator 30

8. Fuse and fuseholder for UL certification units 32

8.1 Fuse and Fuse Code 32

8.2 FuseHolder size 33

9. Fuse and fuseholder for CE mark unit 34

9.1 Fuse and Fuse Code 34

9.2 FuseHolder size 35

Honeywell CD3200 up to110A User’s Manual ver. 2.0

www.honeywell.com/imc 2

10. Modbus communication 36

10.1 Physical requirements 36

10.2 ModBus RTU protocol 36

10.3 Word parameters 41

10.4 Address Configuration 48

11. Maintenance 51

11.1 Trouble Shooting 51

11.2 Repairing procedure 52

11.3 Fans 52

11.4 Servicing 52

11.5 Warranty conditions 52

User’s Manual ver. 2.0 CD3200 up to110A Honeywell

3 www.honeywell.com/imc

CAUTION

Thyristor units are used in power industrial equipment. When the thyristor unit is working, there

are on the unit the following voltages

- Maximum main supply voltage on power terminals up to 600V.

- Auxiliary supply 230-460Vac.

- Fan voltage 230Vac 50/60Hz Power consumption 14W.

Don't remove the plastic cover which provides adequate protection against electric shock.

Don’t use this thyristor in aerospace and nuclear application.

Electric Shock Hazard

When thyristor unit has been connected to main supply voltage and is switched off, before to touch

it be secure that the unit is isolated and wait at least one minute to permit to discharge internal

capacitors. Thus be secure that:

• access to thyristor unit is only permitted to specialized personnel;

• the authorised personnel must read this manual before to have access to the unit;

• the access to the units must be denied to unauthorized personnel.

Important warnings

• Local regulations regarding electrical installation should be rigidly observed.

• Safety regulations must be rigidly observed.

• Don't bend components to maintain insulation distances.

• Protect the units from high temperature, humidity and vibrations.

• Don't touch components to prevent elettrostatichal discharges on them.

• Verify that all ratings are in line with real needs.

• If authorized personnel must measure voltage, current etc. on units, take away rings and other

jewels from fingers and hands.

• Authorized personnel working on thyristor unit under power supply voltage must work on

insulated board. Be secure that board is not connected to earth.

This listing does not represent a complete enumeration of all necessary safety cautions.

Honeywell CD3200 up to110A User’s Manual ver. 2.0

www.honeywell.com/imc 4

Protection

CD3000 thyristor family has a polymeric plastic cover in compliance to International specification

IP20. To understand if IP20 protection is sufficient should be evaluated the installation place where

the units are installed.

Open Type Equipment.

Maximum surrounding air temperature 40°C.

Earth

CD3000 family has isolated heatsink. For safety connect the heatsink to earth to avoid shocks in

case that circuit board or thyristors lost insulation. Earth impedance should be correspondent to

local earth regulation. Periodically the earth efficiency should be inspected.

Electronic Supply

CD3000 family electronic circuit should be supplied by dedicated voltage supply for all electronic

circuit but not in parallel with contactor's coil, solenoids and other inductive or capacitive loads. It's

recommended to use a shielded transformer.

Electromagnetic compatibility

Our thyristor unit has an excellent immunity to electromagnetic interferences if all suggestions

contained in this manual are respected. In respect to a good Engineering practise, all inductive

loads like solenoids contactor coils should have a filter in parallel.

Emissions

All thyristor switching at high speed generate some radiofrequency disturbance. CD3000 serie

complies with EMC rules for CE mark. In many installations near electronic devices has not been

noted problems. If radiofrequency device at low frequency are used near the thyristor unit, some

precautions should be taken like line filters and shielded cables for input signal and for load cables.

LISTED S

NOTE

We reserves the right to apply modifications to the our products without any advice.

User’s Manual ver. 2.0 CD3200 up to110A Honeywell

5 www.honeywell.com/imc

1.Glossary

1.1 Terminology

V: voltage power supply.

I: the full circulating current in thyristor unit.

P: total load power.

1.2 Input signal

SSR: This input type is a square waveform generated by a temperature controller.

AN: Analog input.

IRS: Communication command.

1.3 Power feed back

Feedback: supply voltage fluctuation changes the power to the load. To overcome this effect the

voltage supplied to the load is measured and compared with power demand from controller, the

error signal is used to automatically hold the power at demanded level.

1.4 What is a thyristor unit

A thyristor unit is semiconductor device which acts as a switch formed by two thyristors in

antiparallel. To switch on the alternating current the input signal will be on and the thyristor will

switch off at first zero crossing voltage with no input signal. The benefits of thyristor units

compared with elettromechanical contactors are numerouses: no mooving parts, no maintenance

and capacity to switch very fast. Thyristors are the only solution to control transformers and

special loads that change resistance with temperature and with age.

LOAD

Honeywell CD3200 up to110A User’s Manual ver. 2.0

www.honeywell.com/imc 6

2. Technical specifications

2.1 General Features:

Operating temperature 0÷40°C for higher temperature see derating curve

Voltage power supply 24V minimum, 480V max and 600V on request

Input signal SSR

4÷20mA

0÷10V

potentiometer (10k ohm)

customer configurable with automatic zero/span calibration

Firing mode One of these firing modes can be configured on line via serial port

Phase Angle + Current Limit (PA)

Soft Start + Phase Angle + Current Limit (S + PA)

Auxiliary voltage supply 230V ±15%; 10VA power consumption

440V ±15%; 10VA power consumption

Fan voltage supply 230V ±15%;

110V ±15%; on request

Heater break alarm Discrimination better than 20%. Circuit microprocessor based to

diagnose partial or total load failure and short circuit on Thyristors.

Latching alarm plus reset. Relay output 0,5A at 125V

Feedback Voltage feedbak (V)

Square Voltage feedbak (V²)

Power feedback (VxI) (option)

Serial communication RS485 Modbus protocol (option)

Mounting Din rail mounting up to 45A

Bulk head over 45A

Protection IP20

User’s Manual ver. 2.0 CD3200 up to110A Honeywell

7 www.honeywell.com/imc

2.2 Input features

Input signal Input

Impedance

Analog 0÷10V 8200 ohm

Analog 4÷20mA 100 ohm

Potentiometer

10Kohm 8200 ohm

2.3 Output features

NA=not Available

Current Voltage range Ripetitive peak

reverse voltage Latching

current Max peak

one cycle Leakage

current I2T value for

fusing Frequency

range Power

loss Isolation

Voltage

(A) (V) (440V)

(500V)

(mAeff) (10msec.)

(A) (mAeff) tp=10msec (Hz) I=Inom

(W) Vac

15A 24÷440 1200 NA 150 230 15 610 47÷70 18 2500

25A 24÷440 1200 NA 150 230 15 610 47÷70 30 2500

35A 24÷500 1200 1600 250 400 15 780 47÷70 42 2500

45A 24÷500 1200 1600 250 600 15 1800 47÷70 54 2500

60A 24÷500 1200 1600 450 1000 15 4750 47÷70 72 2500

90A 24÷500 1200 1600 450 2000 15 19200 47÷70 108 2500

110A 24÷500 1200 1600 450 1350 15 8830 47÷70 137 2500

2.4 Derating curve

0.8

0.6

0.4

0.2

045 55 65 75 85

°C

I = I x K

NOMMAX

Honeywell CD3200 up to110A User’s Manual ver. 2.0

www.honeywell.com/imc 8

3. Ordering information

Model CD3200

1 2 3 4 5 6 7 8

CD3200

Ex:CD3200 90A/ 400/ 480/ 460/ SSR/ ZC/ V2/ UL

1 Nominal current of CD3200M

15A 45A 110A

25A 60A

35A 90A

2 Operating Load Voltage (incoming voltage supply)

Specify the value of the line supply.

3 Max VOLTAGE of CD3200

480V

600V

The voltage on the identification label must be equal or more than

operating voltage. The minimum voltage supply to the load is 24V.

4 Auxiliary Voltage

230V 200÷230V ±15%; 10VA

460V 300÷460V ±15%; 10VA

600V 600V ±15%; 10VA (on request)

5 Input

SSR 4÷30VDC

0-10V 0÷10V analog input

4-20mA 4÷20mA analog input

10K pot Potentiometer

6 Firing

PA Phase Angle + Current Limit

S + PA Soft Start + Phase Angle + Current Limit

7 Feedback

V Voltage feedback (V)

V2 Square Voltage feedback (V²)

VxI Power feedback (VxI) (option)

8 Options

COMM MODBUS protocol in RS485 is standard

CD-KP External Keypad

HB Heater Break Alarm

FAN110 Fan voltage supply 110VAC ±15% (std 230VAC ±15%) 14W

50/60Hz

UL UL Certification

EF External fuse and fuseholder

NF No Fuse

Table des matières

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell Fire-Lite Alarms BG-12LPSP Manuel utilisateur

Honeywell

Honeywell N20 Series Manuel d'utilisation

Honeywell

Honeywell MS7510A2008 Manuel utilisateur

Honeywell

Honeywell Spyder PUL1012S Manuel utilisateur

Honeywell

Honeywell AUTOMATIC CONTROL Manuel d'installation et d'exploitation

Honeywell

Honeywell B Manuel utilisateur

Honeywell

Honeywell HR 80 Manuel utilisateur

Honeywell

Honeywell SSW2-1M Manuel utilisateur

Honeywell

Honeywell 10260A Series Mode d’emploi

Honeywell

Honeywell touchpoint Pro Manuel utilisateur

Honeywell

Honeywell Ex-Or MSM2000D Manuel d'installation et d'exploitation

Honeywell

Honeywell HCE80R Manuel utilisateur

Honeywell

Honeywell UDC3200 series Manuel utilisateur

Honeywell

Honeywell Aquastat L7224U Manuel utilisateur

Honeywell

Honeywell PRO 2000 Series Manuel du propriétaire

Honeywell

Honeywell ROBINEX M 100 Manuel utilisateur

Honeywell

Honeywell W7752D2007 Manuel utilisateur

Honeywell

Honeywell UMC800 Manuel utilisateur

Honeywell

Honeywell INCOMM L510 Manuel utilisateur

Honeywell

Honeywell UDC2500 Manuel utilisateur

Honeywell

Honeywell S8600B Manuel utilisateur

Honeywell

Honeywell XL 800 Series Manuel d'installation et d'exploitation

Honeywell

Honeywell Tradeline H1008A Manuel d'utilisation

Honeywell

Honeywell PW-6000 Manuel de l'opérateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur