Honeywell Silent Knight RA-2000 Manuel utilisateur

RA-2000 Remote Annunciator

Installation

The optional Model RA-2000 Remote Annunciator, shown in

Figure 1, performs the same functions as the on-board

annunciator. Operation is identical. The RA-2000 can be surface

or flush monted.

Up to 8 RA-2000s can be added to the IFP-2000 system.

Figure 1: Model RA-2000 Remote Annunciator

RA-2000 installation involves the following steps:

1. Make sure power is off at the panel.

2. Mount the RA-2000 in the desired location (see Section

“Mounting the RA-2000” ).

3. Connect the RA-2000 to the panel (see Figure 2).

4. Use the dipswitches on the back of the RA-2000 to assign

an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N

151430).

5. The RA-2000 module must be added to the system through

programming. JumpStart AutoProgramming will add the

module automatically (refer to Manual P/N 151430).

Wiring Connections

Wire the RA-2000 to the FACP as Shown in Figure 2.

Figure 2: SBUS Connections

Specifications

Mounting the RA-2000

This section of the manual describes mounting the remote

annunciator. The annunciator can be flush- or surface-mounted.

Flush Mounting

This section of the manual describes flush mounting.

Follow these steps to flush mount the RA-2000

1. The back box dimensions are 9-3/8" w x 8-3/8" h. The

minimum depth 2". The back box can be mounted prior to

the complete installation of the RA-2000 using any of the

mounting holes shown in Figure 3.

Figure 3: Back Box Mounting Holes

2. Remove knockout holes as needed for wires. See Figure 4

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 25 mA

Alarm: 50 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

Dimensions:

Flush

Mount:

Overall: 12-1/4” W x 11.5” H x 7/8” D

31.1 cm W x 29.2 cm H x 2.2 cm D

See “Flush Mounting” for back box

dimensions.

Surface

Mount:

Including trim ring:

12-1/4” W x 11.5” H x 3” D

31.1 cm W x 29.2 cm H x 7.6 cm D

Mounting Holes

Model RA-2000 Installation Instructions

2P/N 151443 Rev A

7550 Meridian Circle, Suite 100

Maple Grove, MN 55369-4927

763-493-6455 or 800-328-0103

Fax: 763-493-6475

www.silentknight.com

for backbox knockout locations

Figure 4: Back Box Knockout Locations

3. Wire the Annunciator board to the main control panel. See

Figure 2.

4. Attach the annunciator and door assembly to back box as

shown in Figure 5 using the supplied screws.

Figure 5: Attaching Annunciator/Door Assembly to

Backbox

Surface Mounting

The Model RA-2000TG/TR trim ring kit is available for use

when surface mounting.

1. Remove the desired knock out. See Figure 4.

2. To properly mount the back box, insert a single screw into

the key shaped mounting hole. Do not tighten all the way.

See Figure 6.

Place a level on top of the back box, with the back

box level insert the rest of the mounting screws.

Figure 6: Back Box Surface Mount Holes

3. Run wires to the control panel.

4. Place the trim ring over the back box as shown in Figure 7.

Figure 7: Installing Trim Ring

5. Attach the Door assembly to the back box using screws

provided.

6. After the annunciator wiring to the panel has been

completed, replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws

on the bezel.

Wire Knockouts

Key Shaped

Mounting Hole

Back Box

Mounting Holes

Table des matières

Autres manuels Honeywell Panneau de contrôle

Honeywell

Honeywell Farenhyt Series Manuel technique

Honeywell

Honeywell NOTIFIER NFW-100X Manuel utilisateur

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manuel utilisateur

Honeywell

Honeywell Fire-Lite Alarms MRP-2001 Manuel utilisateur

Honeywell

Honeywell PC8900A Manuel utilisateur

Honeywell

Honeywell Notifier RP-2001 Manuel utilisateur

Honeywell

Honeywell MiniZone EMM-3 Manuel d'utilisation

Honeywell

Honeywell NOTIFIER ID62 Feuille d'instructions

Honeywell

Honeywell LYNX Touch 5100 Mode d’emploi

Honeywell

Honeywell Gamewell GFANN-80 Manuel technique

Honeywell

Honeywell AQ250 Series Manuel d'utilisation

Honeywell

Honeywell Fire-Lite MS-5UD-3 Manuel utilisateur

Honeywell

Honeywell Notifier NFS2-640 Manuel utilisateur

Honeywell

Honeywell NOTIFIER Pearl Guide d'installation

Honeywell

Honeywell Notifier NFS-320/E/C Manuel utilisateur

Honeywell

Honeywell OMNI 408 Instructions de montage

Honeywell

Honeywell Gent Viglion EN54 Manuel d'installation et d'exploitation

Honeywell

Honeywell AQ255 Series Manuel d'utilisation

Honeywell

Honeywell Galaxy Flex Manuel utilisateur

Honeywell

Honeywell GF505 Manuel utilisateur

Honeywell

Honeywell SMX-AUS Manuel utilisateur

Honeywell

Honeywell H-S81-HS Manuel utilisateur

Honeywell

Honeywell ADEMCO VISTA SERIES Guide d'installation

Honeywell

Honeywell Galaxy 16 Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques