Honeywell 8670 Manuel utilisateur
8670-8BBC-EN-QS Rev A
12/18
8670 8-Bay Battery Charger
Quick Start Guide
1
Unpack your Battery Charger
After you open the shipping carton containing the product, take
the following steps:
• Check for damage during shipment. Report damage
immediately to the carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Introduction
The 8670 8-Bay Battery Charger simultaneously charges eight
rechargeable lithium ion batteries. The time required for
charging is dependent upon the battery internal temperature
and condition. The battery charger should be located in an area
that is well ventilated and not in high traffic areas. It should
have enough clearance to allow easy access to the power port
on the back of the device, and be protected from rain, dust,
direct sunlight or inclement weather. The charger is not
approved for use in hazardous locations.
This device is intended for indoor use only and requires an
indoor AC power source. The AC cord should not be stepped on,
tripped over or subjected to damage or stress.
2
Mount the 8670 8-Bay Battery Charger
Place the charger on a horizontal, hard surface or fasten
securely to a wall using the mounting holes. Mounting hardware
is not supplied by Honeywell.
3
Assemble the Power Supply
The AC power supply for the battery charger is shipped with the
battery charger. For non-US models a power cord is required.
1. Plug the A/C power cord into the power adapter.
2. Plug the power cable into the power connector on the back
of the 8670 8-Bay Battery Charger.
3. Plug the A/C power cord into a grounded power source. The
charger is now powered.
The charge pocket LEDs flash while the battery charger enters
and exits the startup check. The battery charger is ready for use
once the charge pocket LEDs are no longer illuminated.
4
Charge the Batteries
Hold the battery with its three charging contacts in line with the
three charging contacts in the charging pocket. Use the direc-
tion of the arrow on the battery label as a guide and align the
yellow dot on the battery with the yellow dot on the charger.
Firmly press the battery straight down into the battery charging
pocket.
It is important that batteries are inserted into the charging
pocket correctly. Inserting the battery incorrectly could result in
damage to the battery or the charger. Do not “slam” or slide the
battery into the pocket. This could damage the charger.
5
When a battery is placed in a charging pocket, the battery char-
ger begins charging the battery. There is a slight delay while the
charger evaluates the condition of the battery before charging
begins. While charging, the charger and battery will generate
enough heat to feel warm. This is normal and does not indicate a
problem. The red LED on the 8-Bay Charger indicates the bat-
tery is charging. A green LED indicates the battery has been
fully charged and can be removed.
Interpret the Charge Pocket LEDs
The battery pocket timers are dynamic and based upon the
capacity of the battery. There is a timeout period for the soft
start and another timeout period for the overall time required to
charge the battery to full capacity.
LED Indication
Red continuous Battery is charging.
Red flashing Battery charger fault or
failure.
Charging pocket timeout
period has expired.
Green continuous Battery charge is complete.
6
Yellow/Amber continuous Battery pocket is in standby
mode while warming up or
cooling down.
Battery is inserted incorrectly.
Make sure charging
terminals on battery and
charger are aligned.
No light on a charge pocket No battery in pocket.
Battery is not fully inserted.
Battery or charger is defective
or damaged.
No light on all charge pockets No power to charger.
No batteries in any pocket.
LED Indication
7
Battery Charger Help
Issue Cause Solution
Battery does
not fit in
charging
pocket
Different
manufacturer's
battery.
Use only Honeywell
lithium ion batteries,
model number HNP-40,
in this charger.
There is an
object in the
charging
pocket.
Unplug charger from AC
supply. Remove any dirt
or foreign objects from
the charging pocket.
No battery in
charger, but an
LED is on
Dirt or foreign
objects are in
the charging
pocket.
Unplug charger from AC
supply. Remove any dirt
or foreign objects from
the charging pocket. If
the LEDs continue to
remain ON, the charger
may be defective.
Contact Support at
www.honeywellaidc.com.
8
Charger is
plugged into a
live outlet,
battery is
inserted, but all
LEDs are off
Battery is not
makingcontact
with terminals
in the pocket.
Push battery in firmly.
Do not “slam” the battery
into the charging
pocket.
Faulty battery. Replace battery. If this
does not correct the
situation, contact
Support at
www.honeywellaidc.com.
Red LED comes
on when a fully
charged battery
is inserted
During the first
few minutes,
the battery
charger checks
the battery for
correct voltage
and charge
state. During
this time the
LED is red.
There is nothing wrong
with the battery or
charger. Do not “top off”
a fully charged battery
by repeatedly placing it
in the charging pocket.
The battery may
overheat and become
damaged.
Issue Cause Solution
9
Red LED is
flashing on any
pocket
Current could
not be sourced
through the
battery due to
age,
exhaustion, or
damage to the
cell(s).
Contact Support at
www.honeywellaidc.com
for battery replacement
options.
The charger’s
timeout period
has expired.
Make sure that the
battery temperature is
within specification and
try charging again. If this
does not correct the
situation, contact
Support at
www.honeywellaidc.com
for battery replacement
options.
Issue Cause Solution
Autres manuels pour 8670
2
Table des matières
Autres manuels Honeywell Chargeur de batteries
Honeywell
Honeywell CT50-HB Manuel utilisateur
Honeywell
Honeywell RP2B Manuel utilisateur
Honeywell
Honeywell 057530.10 Manuel d'instructions
Honeywell
Honeywell Captuvo SL22 Manuel utilisateur
Honeywell
Honeywell COB01 Manuel utilisateur
Honeywell
Honeywell Dolphin 7900 Manuel utilisateur
Honeywell
Honeywell Intermec AC18 Manuel utilisateur
Honeywell
Honeywell NSEK Manuel utilisateur
Honeywell
Honeywell Multi-Bay Battery Charger Manuel utilisateur
Honeywell
Honeywell 010690.01 Manuel d'instructions
Honeywell
Honeywell Marathon Manuel utilisateur
Honeywell
Honeywell Dolphin 9500 Manuel utilisateur
Honeywell
Honeywell 70e-BTSC Manuel utilisateur
Honeywell
Honeywell CX80 Quad Battery Charger Manuel utilisateur
Honeywell
Honeywell PEHA 1602/2 Manuel
Honeywell
Honeywell Impact Series Instructions d'utilisation
Honeywell
Honeywell HomeBase CX80 Manuel utilisateur
Honeywell
Honeywell MB12-BAT-SCN02 Manuel utilisateur
Honeywell
Honeywell CT50-QBC Manuel utilisateur
Honeywell
Honeywell CX80-NB Manuel utilisateur
