Honeywell E3Point Manuel utilisateur
E3Point
Moniteur de gaz à distance
Remote Gas Sensor
Manuel d’utilisation
User Manual
Gas detection device
E3Point Remote
Gas Sensor
User Manual
1998M0773
5/09
E3Point Remote Gas Sensor User Manual i
Symbol Definitions
The following table lists the symbols used in this document to denote
certain conditions:
Symbol Definition
ATTENTION: Identifies information that
requires special consideration.
TIP: Identifies advice or hints for the user,
often in terms of performing a task.
REFERENCE _ INTERNAL: Identifies an
additional source of information within the
bookset.
CAUTION
Indicates a situation which, if not avoided,
may result in equipment or work (data) on the
system being damaged or lost, or may result
in the inability to properly operate the process.
!
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury. It may also be used
to alert against unsafe practices.
CAUTION: Symbol on the equipment refers
the user to the product manual for additional
information. The symbol appears next to
required information in the manual.
!
WARNING: Indicates a potentially hazardous
situation which, if not avoided, can result in
serious injury or death.
WARNING symbol on the equipment refers
the user to the product manual for additional
information. The symbol appears next to
required information in the manual.
ii E
3Point Remote Gas Sensor User Manual
E3Point Remote Gas Sensor User Manual iii
Table of Contents
Symbol Definitions...............................................................i
Introduction..........................................................................1
Description.....................................................................................1
Safety Information ....................................................................1
Installation............................................................................2
Sensor Locations ...........................................................................2
Installation Height ..........................................................................3
Mounting ........................................................................................4
Wiring Diagram ....................................................................5
Connecting Main Sensor to Remote .............................................5
Specifications ......................................................................7
Detection Ranges and Alarm Levels..............................................7
Sensor Overload ............................................................................7
Standard Parts List ........................................................................8
Periodic Inspection and Maintenance ............................................9
Maintenance.............................................................................9
Sensor Life Span......................................................................9
Table of Contents
iv E
3Point Remote Gas Sensor User Manual
E3Point Remote Gas Sensor User Manual 1
Introduction
Description
The E3Point Remote Sensor is a toxic or combustible gas detection
sensor that is compatible with the E3Point Standalone sensor or with
the features offered in certain controller type products, such as the
301C. It provides continuous monitoring for one of the following gases
in ambient air: CO, H2S, O2, NO2, and combustible hazards.
The E3Point is designed to be mounted on an extra wide (2 3/8”)
electrical box.
The E3Point Remote Sensor is intended for use exclusively with the
E3Point Standalone unit. No other uses are supported by Honeywell
Analytics.
Safety Information
Users of the E3Point Remote Sensor require a full understanding of
the installation, operating, and maintenance instructions, otherwise
protection provided by the monitor may be impaired. Read the
following warnings before using the monitor.
!
WARNING:
Install according to local electrical regulations and codes.•
Installationshouldbeperformedbyqualiedpersonnel.•
Do not paint over the sensor screen.•
Ensure the sensor screen is free of dirt and debris.•
Ensure the sensor screen is not covered.•
Do not expose the monitor to electrical shock and/or continuous•
mechanical shock.
Do not expose the sensor to high pressure water spray.•
Do not use the monitor if it is damaged. Before use inspect the•
monitor. Look for cracks, missing metals, or plastics. If the monitor
is damaged, contact Honeywell Analytics immediately.
The warranty will be voided if the customer or any unauthorized•
service personnel attempts to repair the unit.
Installation
Sensor Locations
2 E3Point Remote Gas Sensor User Manual
Installation
Sensor Locations
The following suggestions should be considered to assure detection
of the target gas. Select the most suitable location for each sensor.
Air Currents: If there are fans, wind, or other sources of air
movement, gases may tend to rise or collect in certain areas of a
facility. The local air currents should be assessed to aid in selecting
the sensor location. Air convection can often be more important in
determining gas concentration areas than factors of Vapor Density.
Gas Emission Sources: As a rule, at least one sensor should be
located in close proximity to each point where an emission is likely to
occur.
!
Caution: Because each sensor can only “report” what it is
detecting at the moment, it is very important that the sensor be located
where leaks are most likely to occur.
Autres manuels pour E3Point
3
Table des matières
Langues :
Autres manuels Honeywell Accessoires
Honeywell
Honeywell SiXCT Manuel utilisateur
Honeywell
Honeywell IR800M Guide de configuration
Honeywell
Honeywell WSK-24 Manuel utilisateur
Honeywell
Honeywell UV100RM TrueUV Manuel d'utilisation
Honeywell
Honeywell GENT S4 Manuel d'instructions
Honeywell
Honeywell RPW304 Manuel
Honeywell
Honeywell SK-PHOTO-T-W Manuel utilisateur
Honeywell
Honeywell DC915 series Manuel utilisateur
Honeywell
Honeywell SS431P Manuel utilisateur
Honeywell
Honeywell IS3016 Manuel utilisateur
Honeywell
Honeywell DT906AM Guide de configuration
Honeywell
Honeywell DC311 Series Manuel utilisateur
Honeywell
Honeywell RCW102 Manuel utilisateur
Honeywell
Honeywell DCP917 Series Manuel utilisateur
Honeywell
Honeywell Fire-Lite Alarms SD365TA Manuel utilisateur
Honeywell
Honeywell Notifier FSP-951 Manuel utilisateur
Honeywell
Honeywell Ex-Or BattenFit MSB1000T Manuel d'installation et d'exploitation
Honeywell
Honeywell DFS8M-F Manuel utilisateur
Honeywell
Honeywell IDENTLOC 032236.17 Manuel d'instructions
Honeywell
Honeywell RPW206A Guide de l'utilisateur
