Honeywell Home Evohome Manuel utilisateur
Evohome
Wi-Fi Zone Controller
EN Installation Guide
getconnected.honeywellhome.com
Online Guides
Thanks for choosing evohome
evohome means more comfort, and more control of your heating
system. It’s simple to install and easy to use.
Follow these instructions to set up the evohome system. Devices
that need to be connected to the mains electricity supply should
be installed by a competent person.
Before you start
Make sure you have all the devices you need for your system.
If you used our ‘Design your evohome system’ guide, match
each device to the room or zones in your plan. It’s a good idea
to carry out all the mains electrical and other wiring work first.
In this guide
Step 1: Wire up the heating system 1
Step 2: Set up your evohome Controller 3
Step 3: Power up and bind devices 6
Step 4: System test 13
Configuration and modification 16
ii
Step 1: Wire up the heating system
The evohome Controller communicates with the other wireless devices
in your heating system on a robust 868Mhz signal that is unaffected by
common remote controls or WiFi.
Some of the wireless devices need to be mains powered or connected
to external equipment (such as a boiler) in order to communicate with
the evohome Controller.
It's recommended that these items are installed first to simplify the
binding process later in the setup. The evohome Controller will give on
screen instructions when these devices should be powered up.
1
Installing the Wireless Relay Box (BDR91)
1
Mount the Wireless Relay Box on a nonmetal
surface at least 30cm from your boiler, other
wireless devices or metal objects
2
Release the clip on the bottom to open the
front cover
3
Follow the wiring diagram to connect the
Wireless Relay Box to your boiler’s thermostat
terminals, zone valve or sundial valve, and to
the mains electricity supply
4
Replace the cover
Turn off at mains
and isolate the
supply before
starting. MINIMUM
30CM
BOILER
REPLACE
FRONT
COVER
Refer to boiler instruction to locate
the room thermostat terminals,
determine if the boiler required a
permanent live supply.
2
Step 2: Set up your evohome Controller
The evohome Controller has a guided configuration process to help
you set up the zones for a single type of system.
If you skipped the "Guided Configuration" option when you first
powered up the evohome Controller you can find if again in the
Installation Menu - press and hold the "Settings" button for 5 seconds.
3
Powering up your evohome Controller
1
Remove the cover,
remove the battery
tab and replace
the cover
2
Place it on the table stand or wall bracket
3
Once the batteries are fully charged, the evohome
Controller can be easily removed from the table stand
or wall bracket for ease of programming. After 30
minutes the evohome Controller will emit a beep to
indicate that it should be replaced on the stand or
wall bracket
Your evohome
Controller comes
with *rechargeable
batteries which
are pre-charged
allowing you to
set-up the system
while off the table
stand or wall
bracket.
Place the
evohome
Controller on the
table stand or wall
bracket for normal
use.
* Only use the AA
rechargeable
batteries
provided.
PULL TAB
4
Language selection and WiFi configuration
1
Select a language for the evohome controller user interface
2
Follow the on-screen instructions to connect to a WiFi
network. This enables automatic setting of the date and
time for your location, as well as enabling remote
connectivity via an Apple or Android Smartphone.
• To configure WiFi you will need the home WiFi
network password
3
Instruct the homeowner / user to visit
www.getconnected.honeywellhome.com to create an
account, register the evohome Controller and download
the app
If you don’t
have the WiFi
network details,
or the homeowner
doesn’t require
remote access
you can skip the
WiFi configuration
and proceed with
setting up the
heating system.
WiFi can be
configured later
in the SETTINGS
> WIFI SETTINGS
menu. To create an account and register the evohome Controller, the
homeowner will need the MAC ID and CRC which can
be found:
On a label behind the front cover of the evohome Controller
On screen during the WiFi set-up
In the SETTINGS > WiFi SETTINGS menu after
set-up has been completed
Select you store
Get the App
5
Step 3: Power up and bind devices
Using 'Guided Configuration' on the evohome Controller follow the
on screen instructions and use this section to put the devices into
binding mode.
When you bind a device they permanently store the connection
and there should never be a need to rebind them again - even after
a power cut.
If you skipped the initial set-up, you can find 'Guided Configuration'
mode by pressing 'Setting' for 5 seconds.
If you have other devices to bind, you can see the full installation
guide on getconnected.honeywellhome.com - Your evohome
Controller will give you on-screen instructions to bind the other
components -
just follow the bind instruction for each device in this manual.
6
Make sure the Wireless Relay Box (BDR91)
is wired to the boiler and powered up.
Bind the wireless Relay Box
(BDR91) to control a Boiler
If you do not have any boiler, go to radiator controller binding section.
If you are NOT
following GUIDED
CONFIGURATION
follow these steps
on your evohome
Controller display first:
1
Press and hold
‘Settings’ for
3 seconds
2
Press the green tick
3
Press
SYSTEM DEVICES
4
Press
BOILER CONTROL
5
Press
BOILER RELAY.
evohome
Controller
To bind the Relay Box
1
Press and hold the button for
15 seconds (until the red LED
blinks rapidly) to clear any previous
binding data
2
Press and hold the button again
for 5 seconds (until the red LED
blinks slowly)
3
On the evohome Controller press the green bind
button
4
You should receive a SUCCESS message on the evohome
Controller (if not go back and re-bind)
PRESS
AND HOLD
15 SEC
PRESS
AND HOLD
5 SEC
7
If you are NOT
following GUIDED
CONFIGURATION
follow these steps
on your evohome
Controller display first:
1
Press and hold
‘Settings’ for
3 seconds
2
Press the green tick
3
Press ADD ZONE
4
Type a name for the
new zone and press
the green tick
5
Press RADIATOR
VALVE
6
If you want to
control the zone
temperature with the
evohome Controller
(which needs to be
located in that zone)
press YES, otherwise
press NO.
You must repeat these
steps for each radiator
controller.
evohome
Controller
Power up and bind Radiator Controllers
(HR91 or HR92)
Power up the Radiator Controllers
1
Remove the top cover
2
Open the battery clip and insert the
AA batteries supplied
3
Close the clip and replace the cover
8
Autres manuels pour Evohome
1
Table des matières
Autres manuels Honeywell Home Contrôleurs
Honeywell Home
Honeywell Home Resideo HCC100 Manuel utilisateur
Honeywell Home
Honeywell Home DB7110U Manuel utilisateur
Honeywell Home
Honeywell Home R8182H Manuel utilisateur
Honeywell Home
Honeywell Home H4600A Manuel utilisateur
Honeywell Home
Honeywell Home TheraPro HR90 Mode d’emploi
Honeywell Home
Honeywell Home HR92UK Manuel utilisateur
Honeywell Home
Honeywell Home Lyric LCP500-L Fiche d'information produit
Honeywell Home
Honeywell Home 3000 Series Manuel utilisateur
Honeywell Home
Honeywell Home HR92 Manuel utilisateur
Honeywell Home
Honeywell Home HVC0001 Manuel utilisateur
