Hofmann Geodyna 4801P Mode d’emploi

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 1 of 30

After switching on the machine, the following readings comes up.

Durch drücken der Funktionstaste F1 werden Einstell- und Servicefunktionen zugänglich.

Durch drücken der Funktionstast F1werden Einstell – und Servicefunktionen zugänglich.

By pressing key F1 you enter the configuration menu..

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 2 of 30

The following reading appears:

By pressing 3times key F 6 the key F 4 service routine will be come active.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 3 of 30

The following reading appears:

By pressing key F 4 the the service program become active.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 4 of 30

The following reading appears:

By pressing and holding key F1 C – Codes and by rotating the main shaft

you can select calibration and test codes.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 5 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

57 4

Diameter Distance

The display proceeds automatically to indicate the basic settings.

Cone adator (backing plate) must be installed!

Setting the diameter potentiometer:

Pull out the gauge arm and apply the outer gauge head to the outher surface of the cone adaptor. Adjust

the diameter potentiometers displayed voltage to be within 3.55 and 3.60 V. Turn the potentiometer

shaft to bring the voltage to within this range.

Setting the distance potentiometer:

With the distance gauge arm is in left home position on the axial guide bushing, adjust the distance

potentiometers displayed voltage to be within a range of 0.10 to 0.15 Volt. Turn the potentiometer shaft

to bring the voltage to within this range.

Press the F6 ENTER KEY to store the values.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 6 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

Distance

Pull out the gauge arm exactly 280 mm, hold, and press the F6 ENTER KEY to store the value.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 7 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

Place the calibration weight on top of the cone adaptor, its threaded end pointet vertically upwards. Apply the

diameter gauge arm to the thickest part of the calibration weight and press the F6 ENTER key to store the value.

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 8 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

Next apply the diameter gauge head to the threaded end of the calibration weight and

Press the F6 ENTER KEY to store the value

Calibration is completed and must be stored by entering C90..

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 9 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

C80.

Step no. 5 has no function yet. Press F6 ENTER KEY to continue

Instructions for adjustment Datum 27.04.2005

geodyna 4801P Page 10 of 30

Code C80 Basic settings of the potentiometers

The following reading appears:

Distance

16.

C80.

Raise the gauge arm and pull out at least 3 times slowly until it clamps. After each clamping hold the

gauge arm for at least 1 second in the instantaneous clamping position before repeating this procedure.

When the gauge arm had been pulled out and clamped 3 times, the reading proceeds automatically with

step no. 7.

Table des matières

Autres manuels Hofmann équilibreuse de roues

Hofmann

Hofmann geodyna optima Manuel d'utilisation

Hofmann

Hofmann geodyna 4500-2 Manuel utilisateur

Hofmann

Hofmann geodyna 2600 Manuel utilisateur

Hofmann

Hofmann megaspin 300 Mode d’emploi

Hofmann

Hofmann geodyna 3000 Manuel utilisateur

Hofmann

Hofmann geodyna 990-2 Manuel utilisateur

Hofmann

Hofmann geodyna 6800-2 Manuel utilisateur

Hofmann

Hofmann POWER CLAMP features Manuel d'utilisation

Hofmann

Hofmann geodyna OPTIMA II Manuel utilisateur

Hofmann

Hofmann geodyna 980 L Manuel utilisateur

Hofmann

Hofmann monty UNIVERSAL 2 Manuel utilisateur

Hofmann

Hofmann Geodyna 8250p Manuel utilisateur

Hofmann

Hofmann geodyna 7600 Manuel utilisateur

Hofmann

Hofmann geodyna 6900-2p Manuel utilisateur

Hofmann

Hofmann Snap-on Y2k Manuel utilisateur

Hofmann

Hofmann geodyna 7100 Manuel utilisateur

Hofmann

Hofmann geodyna 6900 P Manuel d'utilisation

Hofmann

Hofmann geodyna 8200 Manuel utilisateur

Hofmann

Hofmann geodyna 7300 Manuel utilisateur

Hofmann

Hofmann Megaspin 800 Mode d’emploi

Hofmann

Hofmann geodyna 980 L Manuel utilisateur

Hofmann

Hofmann Geodyna 8200 Series Manuel utilisateur

Hofmann

Hofmann geodyna 7340 Manuel utilisateur

Hofmann

Hofmann Megaspin 420 Manuel utilisateur

Manuels équilibreuse de roues populaires d'autres marques

Corghi

Corghi PROLINE 640 Manuel utilisateur

IDEAL

IDEAL IWA-60-1500-K Manuel utilisateur

Snap-On

Snap-On WBM250 Manuel utilisateur

Atlas Equipment

Atlas Equipment WB55 Manuel utilisateur

Urrea

Urrea BAL24A Manuel utilisateur

Mondolfo Ferro

Mondolfo Ferro MT 2450 Manuel d'utilisation

CEMB

CEMB K22 Manuel utilisateur

Desoutter

Desoutter Industrial Tools DU Series Manuel utilisateur

HPA-Faip

HPA-Faip B 235 Evo Manuel utilisateur

Bonica

Bonica BC988 Manuel utilisateur

Snap-On

Snap-On EEWB304B Manuel utilisateur

Dannmar

Dannmar DB-70 Manuel utilisateur

Mountz

Mountz MZ-3A Manuel utilisateur

John Bean

John Bean VPI System Manuel utilisateur

PREVOST

PREVOST BAL 250300F Manuel utilisateur

Aston Global

Aston Global ADP-2000L Manuel utilisateur

MANATEC

MANATEC Fox 3D Smart Mobile PT Manuel utilisateur

Coats

Coats Vero Series Instruction manuelle

Hofmann geodyna 4801P Mode d’emploi

Manuels équilibreuse de roues populaires d'autres marques