Hobie 3179 Guide de l'utilisateur
#3179 / Page 1 of 5
#3179 - MOTOR MOUNT HOBIE 16.
Instructions for installation and operation of the "go windward" motor mount.
It is recommended that you read through all of the instructions before you begin the
installation. This product has been handcrafted from the finest aircraft aluminum. Careful
steps have been taken to assure you of many years of trouble free operation. The motor
mount has been designed for the MinnKota M35a Electric Fishing Motor. It is
recommended you use this motor. Other motors may work but adjustments may have to be
made to work properly. Whichever motor you use the control box (or motor head) must be
rotated 180° so that the steering and speed control handle are facing the same direction as
the prop as shown in figure 1. "Modified".
Step 1. Remove screw "A" from beneath the motor head in the shoulder as shown in figure
2. Rotate the motor head 180° and replace screw "A".
Step 2. To install motor mount to front dolphin striker, tilt motor mount box as shown in
figure 3. Set the box on the dolphin striker rods and tilt back as shown in figure 4. You
may want to use your knee to assist as this is a very tight fit to keep vibration to a
minimum. Tilt back until clevis pin can be inserted behind the dolphin striker post insert
clevis pin and key as shown in figure 5.
Step 3. Figure 6. press Tilt Lock Button "A" and hold. Pivot transom clamps upward "B"
and release Tilt Lock Button.
Step 4. Loosen Tension Screw "C". Rotate transom clamp 90°. Center transom clamps
between motor head and prop, tighten tension screw "C" shown bottom of figure 7.
Step 5. We are now ready to install the motor to the "Go Windward" motor mount. Hold
the motor horizontally on each side of the transom clamps. Install motor on the backside of
the "Go Windward" motor mount. Lower motor mount down onto the wooden transom as
illustrated by "D" to "E" in figure 7. Tighten clamps securely. We strongly suggest attaching
a safety line from the motor clamps "B" to the hole conveniently drilled in the super
structure of the "Go Windward" motor mount. The motor is now installed on the boat in
storage position (Top figure 7).
Step 6. Install battery by strapping into "Windward" motor mount box. Tighten restraining
strap. Take care to use only a marine deep cycle battery, marine batteries are sealed to
prevent harm to the environment.
Do not connect the motor to the battery at this time!!!!
#3179 - MOTOR MOUNT HOBIE 16. #3179 / Page 2 of 5
Step 7. To go from the storage position (top figure 7) to a run position (figure 8&9). This
procedure should be done in the water and on the boat. We recommend that you practice
this procedure several times next to shore.
Always make sure the electrical leads are disconnected while adjusting the motor
1. Leaning over the forward crossbar on the prop side of the motor, take firm hold of the
motor shaft.
2. While firmly holding on to the motor shaft, reach through the tramp lacing and loosen
tension lock screw.
3. Slide the shaft until the motor head is against the transom clamp (see figure 8). The
motor has a tendency to twist. Make sure motor head and prop remain parallel to the
tramp. Through the lacing, tighten the tension locking screw.
4. While firmly holding on to the motor shaft, reach through tramp lacing, push and hold
down the Tilt Lock Button. Be careful not to pinch your fingers! With your arm lower
motor into run position (see figure 9).
5. Adjust (if necessary) for a true forward position.
6. Reverse this procedure to return to the storage position.
Step 8: While motor is in running position (locked straight ahead), you may connect the
battery leads and control the motor speed by reaching between the tramp lacing. You may
now steer the rear rudders.
CAUTIONS:
1. Never leave battery leads connected during installation and de-installation as well as
moving from a storage position to run position and vice versa. The reason for this is
the limited clearance under the tramp may cause motor to turn on damaging the
tramp r causing injury to the operator.
2. Take care not to run aground with the motor in the run position. This will cause
damage to everything and has a tendency to be expensive.
3. Remember the motor head is not designed to be submerged in water.
4. Always leave motor in stored position when sailing. Motor or sail, but don't do both!
5. This product was not designed for use in heavy air! This could cause damage to the
motor, motor mount or boat. IF it is howling, what do you need a motor for anyway?
#3179 - MOTOR MOUNT HOBIE 16. #3179 / Page 3 of 5
#3179 - MOTOR MOUNT HOBIE 16. #3179 / Page 4 of 5
#3179 - MOTOR MOUNT HOBIE 16. #3179 / Page 5 of 5
ADDITIONAL MINNKOTA MODIFICATION INSTRUCTIONS
This set of instructions is optional. These are provided for the people that would like to
have more clearance between the motor head and the tramp. Step 1 in these instructions
is the same as Step 1 in the instructions for the installation and operation instructions
except you should not have to rotate the motor head as is has already been done.
Step 1. Remove screw "A" from beneath the motor
head in the shoulders as shown in figure 1.
Step 2. Gently lift up the motor head exposing the
wires that run between the motor head and
motor. On the underneath side of the motor
head you will find 4 screws. Remove the
screws as shown in figure 2. This allows the
separation of the motor head housing. Gently
lift up the motor housing cover exposing the
terminating block for the motor wires.
Step 3. Loosen the thumb-screw on the depth collar
and slide it towards the motor head until it is free of the tube.
Step 4. Taking one wire at a time, remove from the
terminating block. Thread the wire through the
bottom of the motor head and the depth collar.
Re-thread the wire back through the bottom of
the motor head (not through the depth collar)
and reconnect to the terminating block. Then
proceed with the next wire and then next until all
wires have been reconnected.
Step 5. Re-assemble the motor head.
Table des matières
Autres manuels Hobie Équipement nautique
Hobie
Hobie Mirage Drive Manuel utilisateur
Hobie
Hobie Getaway Hatch Manuel utilisateur
Hobie
Hobie Mirage Adventure Island Manuel utilisateur
Hobie
Hobie Mirage Tandem Manuel utilisateur
Hobie
Hobie Livewell V2 Manuel utilisateur
Hobie
Hobie Mirage Compass Manuel utilisateur
Hobie
Hobie Mirage Drive Manuel du propriétaire
Hobie
Hobie Mirage Tandem Manuel utilisateur
Hobie
Hobie 30116 Manuel utilisateur
Hobie
Hobie 84500111 H-BAR Manuel utilisateur
Hobie
Hobie INFLATABLESTAND UP PADDLEBOARD Manuel du propriétaire
Hobie
Hobie MirageDrive Mode d’emploi
Hobie
Hobie Mirage Drive Mode d’emploi
Hobie
Hobie 38584001 Manuel de la liste des pièces
Hobie
Hobie Wave Manuel utilisateur
Hobie
Hobie 30113 Manuel utilisateur
Hobie
Hobie Mirage Tandem Manuel utilisateur
Hobie
Hobie 38040011 Manuel utilisateur
Hobie
Hobie Twist-n-Seal Hatch Manuel utilisateur
Hobie
Hobie 21380001 Manuel utilisateur
Manuels Équipement nautique populaires d'autres marques
Humphree
Humphree HCS-5 Manuel utilisateur
Vetus
Vetus BOW4512D Fiche technique
Dock Doctors
Dock Doctors SLIDING BOARDING STEP Manuel utilisateur
Mastervolt
Mastervolt Mass Combi 12/2000-100 Instructions d'utilisation d'origine
Zattini Group
Zattini Group bamar BOXTRON E14S Guide de l'utilisateur
SeaView
SeaView PM5-FMD-8 Manuel utilisateur
