Hobie 14 Manuel utilisateur

#13070100 / Page 1 of 1

#13070100 - COMPTIPTM RETROFIT INSTRUCTIONS

HOBIE 14, 16, 18 AND HR14

1) REMOVE MAST TANG OR TANGS (HR14) BY DRILLING OFF RIVET

HEADS W/ A 13/64” (4 MM) DRILL BIT AND PUNCHING RIVET CASINGS

AND CAPS THROUGH.

2) MEASURE FROM THE BOTTOM OF THE

MAST EXTRUSION (NOT INCLUDING MAST

BASE). NOTE: CUT SHOULD BE ABOVE

TANG RIVET HOLES!

MARK AND CUT OFF MAST SQUARE AT THE

APPROPRIATE LENGTH. (HINT: WRAP A

SHEET OF PAPER AROUND THE MAST AND LINE UP EDGES TO MAKE

A PERFECTLY SQUARE MARK ALL AROUND THE MAST. TAPE IN

PLACE AT THE CUT POINT. PENCIL A THICK LINE ALL AROUND THE

MAST FOLLOWING THE PAPERS EDGE. WITH A HACK SAW, START

CUTTING ON THE LINE AND ROLL THE MAST OVER AS YOU CUT. CUT

A “TRENCH” ALLAROUND THE MAST BEFORE CUTTING THROUGH

WHILE ROLLING THE MAST SLOWLY OVER. (STARTING A CUT AND

CONTINUING STRAIGHT THROUGH MAY NOT CUT STRAIGHT.)

3) DRILL A 3/8" DIA. HOLE, 9" DOWN FROM CUT (ON THE FRONT) AS SHOWN (FIG. 1).

4) INSERT ETHAFOAM PLUG TO A DEPTH OF 12" (FIG. 2). THIS PLUG MAY BE GLUED IN PLACE

WITH PLENTY OF 3M 5200 OR SIKAFLEX IF DESIRED. OTHERWISE USE FOAM INJECTION AS

DESCRIBED BELOW. IF GLUED IN PLACE, THE PLUG MUST CURE FOR 24 HOURS BEFORE

CONTINUING INSTALLATION.

5) FILE COMPTIPTM FOR A SNUG FIT INSIDE EXTRUSION. CHECK THAT TIP WILL FULLY INSERT.

6) PLACE LOWER MAST ON SAW HORSES OR LARGE TABLE WITH MAST BASE AGAINST SOLID

PADDED OBJECT (THAT YOU CAN BE BANG MAST BASE AGAINST). GLUED ASSEMBLY WILL HAVE

TO BE HELD LEVELAND SQUARE WHILE CURING, PREPARE ADDITIONAL SAW HORSE IF

NECESSARY.

7) MASK OFF EXTRUSION AND LUFF TRACK OPENINGS AS WELL AS COMPTIPTM. SPREAD EPOXY

OR POLYESTER PUTTY INSIDE OF EXTRUSION AT CUT END TO A DEPTH OF 6". SPREAD

MATERIAL OUTSIDE ON COMPTIPTM JOINT.

8) INSERT COMPTIPTM. HOLD TIP WHILE INSERTING. PUSH INTO EXTRUSION WITH MAST BASE AGAINST SOLID OBJECT. AS TIP

GETS TIGHTER, PULL ENTIRE ASSEMBLY BACK AWAY FROM THE SOLID OBJECT, THEN SHOVE BACK AGAINST IT (IN A BATTERING

RAM MOTION). REPEAT UNTIL TIP IS FULLY INSERTED. BRACE ASSEMBLY IN A POSITION TO HOLD MAST AND TIP SQUARE ON ALL

AXIS AS EPOXY CURES.

9) H-16 NOTE: IF TANG IS AN OLD STYLE OR IS DAMAGED REPLACE IT. CURRENT TANG HAS 3 HOLES FOR STAYS AND TRAPEZE

WIRE ATTACHMENT. USING EXISTING HOLES IN EXTRUSION, DRILL COMPTIPTM FOR TANG RIVET AND SLEEVES WITH A 13/64” (4

MM) DRILL BIT AND REINSTALL MAST TANG WITH RIVETS AND RIVET CAPS.

INTERNAL SEALING PLUG:

10) TAPE OFF AREA AROUND 3/8" HOLE TO REDUCE CLEANUP AFTER FOAM INSTALLATION.

11) TILT MAST FOR FOAMING, HEAD DOWN, AS SHOWN. (FIG. 3)

12) (READ FOAM INSTRUCTIONS PRIOR TO USE) INJECT A/B

URETHANE FOAM INTO 3/8" HOLE" (APPROX. 3 SECOND SQUIRT)

PLUG HOLE WHILE FOAM EXPANDS. FOR BEST RESULTS, FOAM AND

MAST SHOULD BE ABOVE: 70° F.

13) AFTER FOAM HAS CURED FOR AN HOUR OR MORE, CLEANUP UP

EXCESS WITH A SINGLE EDGE RAZOR BLADE AND INSTALL 3/8"

PLUG INTO 3/8" HOLE.

CUT LENGTHS ARE:

H14 I5' 1 1/8"

H16 18’ 3 3/4"

H18 20’ 5 3/8"

HR14 14' 4 3/8"

Autres manuels pour 14

1

Ce manuel convient aux modèles suivants

4

Autres manuels Hobie Bateau

Hobie

Hobie Holder 12 Manuel utilisateur

Hobie

Hobie Mirage Pro Angler 17T Manuel utilisateur

Hobie

Hobie Bravo Manuel utilisateur

Hobie

Hobie 15 Club Manuel utilisateur

Hobie

Hobie Twixxy Manuel utilisateur

Hobie

Hobie kayak Manuel utilisateur

Hobie

Hobie catsy Manuel utilisateur

Hobie

Hobie 3.5 Guide de démarrage rapide

Hobie

Hobie Wave Manuel utilisateur

Hobie

Hobie Mirage Compass Manuel utilisateur

Hobie

Hobie 16 Manuel utilisateur

Hobie

Hobie Quest 13 Manuel utilisateur

Hobie

Hobie HC 16 Guide de configuration

Hobie

Hobie Gateway Manuel utilisateur

Hobie

Hobie TriFoiler Manuel utilisateur

Hobie

Hobie Wave Manuel utilisateur

Hobie

Hobie Getaway Guide de configuration

Hobie

Hobie PEARL Manuel utilisateur

Hobie

Hobie Mirage Drive Manuel

Hobie

Hobie 17 Manuel

Hobie

Hobie Mirage Vantage CT Manuel utilisateur

Hobie

Hobie 14 Turbo Manuel utilisateur

Hobie

Hobie Wave Manuel utilisateur

Hobie

Hobie Mirage Outback Manuel utilisateur

Manuels Bateau populaires d'autres marques

Raymarine

Raymarine ST70 Instrument Manuel utilisateur

Pro-Line Boats

Pro-Line Boats Pro Line 19 Sport Manuel utilisateur

Jeanneau

Jeanneau CAP CAMARAT 8.5 CC Manuel utilisateur

Tiara Yachts

Tiara Yachts C49 2024 Manuel utilisateur

Monterey Boats

Monterey Boats Sport Yacht 330 Manuel utilisateur

J

J 105 Manuel utilisateur

PURSUIT

PURSUIT OS 335 Manuel utilisateur

Boston Whaler

Boston Whaler CONQUEST 345 Manuel utilisateur

Jeanneau

Jeanneau SUN ODYSSEY 41 DS Manuel utilisateur

Meridian

Meridian 490 Pilothouse Manuel utilisateur

Advanced Elements

Advanced Elements AdvancedFrame Expedition AE1009 Manuel utilisateur

Robo Marine Indonesia

Robo Marine Indonesia GEOMAR Manuel utilisateur

Swallow Boats

Swallow Boats BayRaider Manuel utilisateur

Intex

Intex Excursion 5 Set Manuel utilisateur

X SHORE

X SHORE EELEX 8000 Manuel utilisateur

ISLAND PACKET

ISLAND PACKET 370 Manuel utilisateur

Sea Ray

Sea Ray 175 Sport Manuel utilisateur

Regal

Regal 2300 Manuel utilisateur