HL-Tech WL-3002 Guide rapide
WLAN 802.11 b/g MiniPCI
WL-3002
Hardware Installation and
Configuration Utility User’s Guide
Integrated Baseband and MAC Solution
IEEE 802.11b/g WLAN
WL-3002 User’s Manual
HL-TECH Corporation 2
Contents:
Table of Contents .……….……….………..……….…………...2
Introduction ….…………………………………………………..3
Install the WLAN card in PC/NB………….……….….………..4
Install WL-3002 driver…….………………….…….…………..5
Setup WL-3002 Configuration Utility…………….…………….7
WL-3002 User’s Manual
HL-TECH Corporation 3
Introduction
The Wireless LAN Configuration Utility is a powerful application that helps you to
configure this WLAN card and monitor the statistics of the communication status. Unlike
the standard method of configuring the card via the operating system utilities, this
application permits the dynamic modification of the configuration parameters while the
card is operating. It also offers more configuration options.
We offer the Wireless LAN Configuration Utility for Windows® 98SE/Me/2000/XP.
Mini-PCI WLAN equipment has been tested and found to comply with limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in residential installations.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
WL-3002 User’s Manual
HL-TECH Corporation 4
Install the WLAN card in PC/NB
Release the screw from PC/NB
Find out the pre-wired cable
Connect the cable with Mini-PCI
Align and firmly plug the Mini-PCI card
into the slot.
Re-place the cover to PC/NB
Secure the screw with a cross screwdriver.
WL-3002 User’s Manual
HL-TECH Corporation 5
Install WL-3002 driver
The program will automatically proceed with
installing.
Press “Next” to continue
Press “Browser” to change the folder where setup
will install files or press “Next” to continue.
Select or create a program folder and press
“Next” to continue.
The program will automatically proceed with
installing.
Press “Yes” to continue.
WL-3002 User’s Manual
HL-TECH Corporation 6
Press “Continue” to continue the process. Insert the Wireless Card to slot of NB and choose
“Install the software automatically
(Recommended)” and press “Next”.
Press “Finish” to complete the installation
WL-3002 User’s Manual
HL-TECH Corporation 7
Setup WL-3002 Configuration Utility
1. Station:
Figure 1-1
Open the WL-3002 Configuration Utility shown as Figure 1-1. The adapter can be set at
“Station” or “Access Point” Mode from the Mode drop down menu. Station mode is
selected for the item.
You can site survey the neighboring SSID site by pressing the “Refresh”, then sites
name and signals strength of available SSID sites are shown on the “Available
Network” field.
Double click the SSID site from “Available Network” field, and the SSID can be
connected directly.
The information of the SSID is shown on the “ Current Network Information”.
Show the BSSID of connecting AP on the “Link Status” filed.
“Signal Strength” and “Link Quality” shown on diagrammatic curve, and described
with percentage.
Record the number of Tx frames on the filed of “Tx Frame”.
Record the number of Rx frames on the filed of “Rx Frame”.
WL-3002 User’s Manual
HL-TECH Corporation 8
1.1 More Setting
Press “Connetc this site “ in Figure 1-1to enter “More setting“ window.
Figure 1-2
1.1.1 “General Connection Setting” group:
Read the current status from the group if the “Change” button is not pressed.
Press “Change” button for modifying the status, when the modification is finished,
press “Apply” to save it. The button “Change” and “Apply” is alternately shown on
the same position.
Modify the SSID name from the “SSID” field. When use the item, the “any “will be
unchecked previously.
Change the channel by drop down menu “ Channel”. When use the item, the
Ad_Hoc Mode will be set previously.
Select the transmission rate by “ Tx Rate” drop down menu.
Select the “Ad_Hoc” or “Infrastructure” Mode by the “Network Type”
drop down menu.
Select the “Enable WEP” or “Disable WEP” by the “Encryption” drop
down menu.
Select the “Open System” , “Shared Key” mode or “Auto” from the
“Authentication Mode” drop down menu.
WL-3002 User’s Manual
HL-TECH Corporation 9
1.1.2 Encryption Setting
1.1.2.1 WEP Key Setting
Press “WEP Encryption Setting” in Figure 1-2 to enter the “WEP Key Setting” page
Figure 1-3
Select the “Open System” , “Shared Key” mode or “Auto” from the “authentication
Mode” drop down menu.
Press the “Change” button to modify the contents of “WEP Key setting”, when it is
finished, press “Apply” to save it. The button “Change” and “Apply” is alternately
shown on the same position.
Select which key length 64,128 or 256 bits will be modified or used by “Key
Length” item.
Select which key set will be use by the field of “Default Key ID”
Modify the 4 sets key depending on the selected key length on the field of “Key
Value”. The key value is used the hexadecimal format.
Select which key format “hexadecimal” or “ASCII” will be used from the “Key
Format”
WL-3002 User’s Manual
HL-TECH Corporation 10
1.1.2.2 WPA Setting
Press “WPA Encryption Setting” in Figure 1-2 to enter the “WPA Setting” page
Figure 1-4
You can select the WPA authentication protocol “TLS” or “PEAP” from “Protocol”
filed. The TLS is used , the User name and Password need not to be used , but the
Certificate need to be used. If the PEAP is used , the User name , Password and
Certificate need to be used.
If you select “pre-share-key” protocol , you can write down your password on the
filed of “Passphrase” , the password length can be selected from 8 bytes to 63 bytes
(ASCII format) depend on user .
Table des matières
Manuels Carte PCI populaires d'autres marques
Belkin
Belkin F5D7000F Manuel utilisateur
Pericom
Pericom PI7C7100 Manuel utilisateur
ADLINK Technology
ADLINK Technology cPCI-3548 Manuel utilisateur
Digium
Digium TE200 Series Manuel utilisateur
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur
Western Digital
Western Digital FireWire PCI Adapter Manuel utilisateur