HiTRAx 42.7003 Manuel utilisateur

GUIDE

Cat. No. 42.7003

Instruction Manual

INTRODUCTION

This device is a digital product that provides altimeter, barometer, compass, altimeter data, dual time,

chronograph, chronograph data and alarm functions.

Features:

Altimeter

- 1 meter (or foot) resolution and with working range from -700 meters (-2296 feet) to 9000 meters (29520 feet).

- Graphical expression of changes provided.

- Unit in meters or feet selectable.

- 20 memories with date, time and altitude reading.

Barometer

- 1 hPa resolution and with working range from 300 hpa to 1100 hpa.

- Graphical expression of changes provided.

- Both sea level pressure and absolute pressure can be shown.

- Weather forecast.

- Temperature displayed in °F or °C selectable.

Compass

- Electronic compass providing 16 cardinal indications together with bearing in degrees.

- Declination correction provided.

Time

- 2 time modes selectable.

- Presents day of the week, day, hours, minutes and seconds (year and month can also be set).

- 12/24-hour formats selectable.

- Auto-calendar from 2000 to 2049.

Chronograph

- 1/100-second resolution with working range up to 24 hours.

- 100 memories for lap/split times stored in a maximum of 30 runs.

Alarm

- 2 daily alarms.

- Hourly chime.

Electro-luminescent backlight

-3 seconds light up EL backlight.

Altimetermode with altitude change: measures every2,5 seconds

Altimetermode without altitude change (barometer mode): every2,5 minutes

Barometermode: measures every2,5 minutes. Changes to Time mode after 24 hours

Temperature: measures every2,5 minutes.

BASIC OPERATION OF BUTTONS

A: - SWITCH AMONG DISPLAYS

- TAKE BEARING

- STORE ALTITUDE DATA (PRESS AND HOLD)

- FORWARD SELECTION OF ALTITUDE DATA

- START/LAP OF CHRONOGRAPH

- RETRIEVE DATA IN RUN

- TURN ALARM ON AND OFF

- FORWARD SETTING (SET OR CALIBRATION)

B: - SWITCH BETWEEN NORMAL TIME AND DUAL TIME (PRESS AND HOLD)

- SWITCH BETWEEN UNITS OF TEMPERATURE (PRESS AND HOLD)

- SWITCH BETWEEN UNITS OF ALTITUDE (PRESS AND HOLD)

- REVERSE SELECTION OF ALTITUDE DATA

- STOP CHRONOGRAPH

- STORE CHRONOGRAPH DATA (PRESS AND HOLD)

- SELECT RUN NUMBER

- SWITCH BETWEEN ALARM 1 AND ALARM 2

- REVERSE SETTING (SET OR CALIBRATION)

C: - MODE CHANGE

- DIRECT CHANGE TO TIME MODE (PRESS AND HOLD)

- ADVANCE TO NEXT SETTING (SET OR CALIBRATION)

D: - EL BACKLIGHT

- ENTER SET OR CALIBRATION (PRESS AND HOLD)

- CLEAR DATA (PRESS AND HOLD)

- EXIT (SET OR CALIBRATION)

E: - SWITCH AMONG DISPLAYS

- SWITCH BETWEEN DATE AND ALTITUDE READING DISPLAYS

- SHOWNUMBER OF UNUSED LAP

EL BACKLIGHT

Press D for EL backlight with 3 seconds auto light up.

MODE CHANGE OPERATION

There are 9 modes: Normal Time, Dual Time, Compass, Barometer, Altimeter, Altimeter Data, Chronograph,

Chronograph Data and Alarm.

Press Cto change from mode to mode, hold down B to switch between Normal Time mode and Dual Time mode

as in the following:

* At any mode, holding down C will change to Time mode directly.

NORMAL TIME

COMPASS

BAROMETER

ALTIMETE

ALTIMETER DATA

DUAL TIME

Hold B

CHRONOGRAPH

CHRONOGRAPH DATA

ALARM

TIME MODE

Use C to enter Time mode.

* Mode prompt “TIME” is displayed first.

- There are 2 time modes, Normal Time (indicated by T1) and Dual Time (indicated by T2), and they count up

individually with the same second.

- There are 3 displays for time. They are Time, Time with Barometer and Time with Weather.

- There is an auto-calendar from 2000 to 2049.

To switch between Normal Time and Dual Time

Hold down B until the mode indicator (T1 or T2) stops flashing to switch between Normal Time mode and Dual

Time mode.

To switch among the 3 time displays

Use A or E to switch among the 3 displays for time.

* “TIME”, “BAROMETER” or “WEATHER” is displayed first.

* Graph of sea level pressure is described in BAROMETER MODE.

To set time

1. Hold down D until the hour digits start to flash on the display, which indicates the setting screen.

TIME/BAROMETER

A or E

TIME TIME/WEATHER

A or E

Aor

Temperature

Graph of

sea level pressure

Current sea level pressure

Weather

indicators

Time

Dayof the

week

Day

Unit indicator

of temperature

Hold B

2. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed.

3. Press C to advance to the next setting as in the following:

* When second digits are flashing, press Aor Bto reset the digits to 00. Resetting seconds when the digits are

between 00 to 29 will leavethe minute digits unchanged, or between 30 to 59 will increase the minute digits by

one.

* When 12 or 24 is flashing, press Aor Bto switch between 12- or 24-hour formats. If 12-hour format is chosen,

AM or PM indicator will be shown.

4. Press D to exit the setting screen and day of the week will be adjusted automatically.

* If there is no button operation for 2-3 minutes at setting screen, the display will return to Time mode

automatically.

COMPASS MODE

Use C to enter Compass mode.

* Mode prompt “COMP” is displayed first and bearings will be taken automatically.

- Compass mode indicator is shown.

- When you take bearings, readings are shown in 16 cardinal indications together with bearing in degrees.

* Reading shown indicates the direction that the LCD’s 12 o’clock position is pointing to.

- North-South arrowis shown on circumference of the LCD.

* North is indicated by 1 flag and South is indicated by 3 flags.

- Declination correction is provided.

* Declination is the difference between true north and magnetic north.

Importance

1. The compass should be calibrated before use.

2. The compass must be kept in a level position when in use.

3. Compass readings are easily affected by disturbing sources of magnetism, so the compass should always be

used in the open air.

To calibrate the compass

1. Hold down D until “CAL” is shown on the display, which indicates the calibration screen.

Hold D

CALIBRATION SCREEN

HOUR MINUTE SECOND YEAR

MONTHDAY12/24H

C C C

CCCC

TENS OF DEGREE DEGREE E/W

2. Rotate the product clockwise slowly for 2 complete rotations

*Each rotation must last for at least 15 seconds. Keep the watch in a level position when calibrating. Do avoid

close contact to metal parts or other electrical instruments, when calibrating.

3. Press D and the ten-degree digit starts to flash on the display, which indicates the declination angle setting

screen.

* Press A will end calibration skipping the declination angle setting. In this case, the declination angle is set to

0 degree.

4. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed.

5. Press C to advance to the next setting as in the following:

* When E or Wis flashing, press A or B to switch between East and West.

* You should consult your local organization for information of declination. Declination angles for major cities

are listed belowfor reference only.

City Declination

Angle City Declination

Angle

Anchorage 22° E London 4° W Rio De Janeiro 21° W

Atlanta 4° W Little Rock 3° E San Francisco 15° E

Bombay 1° W Livingston, MT 14° E Seattle 19° E

Boston 16° W Munich 1° E Shanghai 5° W

Calgary 18° W NewYork City 14° W Toronto 11° W

Chicago 3° W Orlando 5° W Vancouver 20° W

Denver 10° E Oslo 2° W Washington DC 10° W

Jerusalem 3° E Paris 2° W Waterbury, CT 14° W

6. Press D to end calibration.

* If “ERR” indicating error is displayed, calibrate the compass again.

* If there is no button operation for 2-3 minutes during calibration or at declination angle setting screen, the

display will return to Compass mode automatically.

To take bearings

1. Press A, bearings will be taken and shown for about 10 seconds.

* If no bearing is being taken, the display shows “----”.

2. Hold down A, bearings will be taken and shown continuously and for 10 seconds more after A is released.

BAROMETER MODE

Barometer mode indicator

Use C to enter Barometer mode.

* Mode prompt “BARO” is displayed first.

- Barometer mode indicator is shown.

- The barometer is of 1 hPa resolution and with working range from 300 hpa to 1100 hpa.

- Both sea level pressure and absolute pressure can be shown.

- Graph showing the changes in sea level pressure is provided.

* Graph will be cleared only after battery replacement or reset.

- Weather forecast (indicated by the weather indicators) for the coming 24-48 hours is provided.

* Forecast is accurate only if the barometer has been functioning for at least 12 hours.

- Temperature is of 0.1 degree resolution and with working range from -4°F (-20°C) to 158°F (70°C). And unit in

°F or °C selectable.

- There are 3 displays for Barometer mode.

To switch among the 3 displays for barometer mode

Use A or E to switch among the 3 displays for barometer mode.

Reading the graph of sea level pressure

The graph shows the relative changes in sea level pressure in the past with the current pressure represented on

the right. Each horizontal point represents one hour while each vertical point represents the relative reading of

pressure in that time.

*It is not possible to get the exact reading from the graph. User can only get the trend of changes from the graph.

Temperature

A or E

Absolute

A or E

Time

indicator

To switch between °F and °C

1. Use A or E to switch to the barometer display with temperature.

2. Hold down B until the unit indicator (°F or °C) stops flashing to switch temperature between °F and °C.

To set sea level pressure reading

1. Hold down D until “SET CURRENT WEATHER” scrolls on the display, which indicates the weather setting

screen.

* The weather indicators start to flash.

2. Press C, “SET SEA LEVEL PRESSURE” scrolls on the display, which indicates reading setting screen.

* The current sea level pressure reading starts to flash.

3. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed.

4. Press D to exit the setting screen.

* If there is no button operation for 2-3 minutes at setting screen, the display will return to Barometer mode

automatically.

To set current weather

1. Hold down D until “SET CURRENT WEATHER” scrolls on the display, which indicates the weather setting

screen.

* The weather indicators start to flash.

2. Use A (+) and B (-) to change the setting as in the following:

3. Press D to exit the setting screen.

* If there is no button operation for 2-3 minutes at setting screen, the display will return to Barometer mode

automatically.

BBB

AAA

ALTIMETER MODE

Use C to enter Altimeter mode.

* Mode prompt “ALTI” is displayed first.

- Altimeter mode indicator is shown.

- The altimeter is of 1 meter (or foot) resolution and with working range from -700 meters (-2296 feet) to 9000

meters (29520 feet).

- Altitude reading in meters or feet selectable.

- Graph showing the changes in altitude is provided.

* Graph will be cleared only after battery replacement or reset.

- Maximum 20 altitude data can be stored.

Reading the altitude graph

The altitude graph shows the relative changes in altitude in the past with the current altitude represented on the

right. Each horizontal point represents 15 minutes while each column represents the relative reading of altitude

in that time.

*It is not possible to get the exact reading from the graph. User can only get the trend of changes from the graph.

To switch between meters and feet

Hold down B until the unit indicator (M or Ft) stops flashing to switch altitude reading between meters and feet.

To store altitude data

Hold down A until “DATA” stops flashing to store the current altitude data.

* “STORED” and data number are shown.

To calibrate altitude reading

1. Hold downDuntil the current altitude reading starts to flash on the display, which indicates the setting screen.

2. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed.

3. Press D to exit the setting screen.

* If there is no button operation for 2-3 minutes at setting screen, the display will return to Altimeter mode

automatically.

Table des matières

Autres manuels HiTRAx Montre

HiTRAx

HiTRAx HIKE Manuel utilisateur

Manuels Montre populaires d'autres marques

Pandora

Pandora WATCH2 Manuel utilisateur

Casio

Casio QW-4343 Manuel utilisateur

Suunto

Suunto X6 Manuel utilisateur

Seiko

Seiko N830 Manuel utilisateur

MotionX

MotionX 365 Manuel utilisateur

Garmin

Garmin VENU SQ 2 Manuel utilisateur

QCY

QCY Watch GTC Manuel utilisateur

Canyon

Canyon Cindy CNE-KW41WP Manuel utilisateur

Esq

Esq Watches Guide d'installation

Crane

Crane AA5-CDSM-3A Manuel utilisateur

Timex

Timex W-214 Manuel utilisateur

DETOMASO

DETOMASO MATERA Manuel utilisateur

Geemarc

Geemarc Watch N Shake Manuel utilisateur

LORUS

LORUS W590 Manuel utilisateur

STENLILLE

STENLILLE Actío Manuel utilisateur

Casio

Casio 5594 Manuel utilisateur

Sinn

Sinn HUNTER'S WATCH 3. Edition Manuel utilisateur

Slazenger

Slazenger SLZ800 Manuel utilisateur