Hitachi DP05 Manuel utilisateur

SAFETY PRECAUTIONS......................................................................................................2

TECHNICAL CAUTIONS ......................................................................................................3

SPECIFICATIONS ................................................................................................................4

GENERAL INFORMATION....................................................................................................5

CUSTOMIZED PICTURE AND SOUND ADJUSTMENTS ....................................................6

SERVICE ADJUSTMENTS..................................................................................................11

DC VOLTAGE ......................................................................................................................19

WAVEFORMS......................................................................................................................30

BASIC CIRCUIT DIAGRAM ................................................................................................33

PRINTED CIRCUIT BOARDS ............................................................................................46

BLOCK DIAGRAM ..............................................................................................................47

WIRING DIAGRAM..............................................................................................................48

CHASSIS WIRING DRAWING ............................................................................................49

EXPLODED VIEW ..............................................................................................................55

REPLACEMENT PARTS LIST ............................................................................................57

EXPLODED VIEW PARTS LIST..........................................................................................84

QUICK REFERENCE PARTS LIST ....................................................................................85

PA No. 0132

NTSC DP05/DP05F Chassis R/C: CLU-572TSI

R/C: CLU-575TSI

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

AUGUST 2000 HHEA-MANUFACTURING DIVISION

43FDX01B

53FDX01B

SERVICE MANUAL

This addendum gives differences between DP05/DP05F and the DP06 chassis models. For any

other information, see the DP06 chassis Service Manual PA No. 0131 issued in JUNE 2000.

CAUTION: Before servicing this chassis, it is important that the service technician read the

”Safety Precautions” and “Servicing Precautions” in Service Manual PA No. 0131.

PROJECTION COLOR TELEVISION

Components having special safety characteristics are identified by a on the schematics and on the parts list in this serv-

ice manual and its supplements and bulletins. Before servicing this chassis, it is important that the service technician read

and follow the “Safety Precautions” and the “Servicing Precautions” in Service Manual PA No. 0131.

For continued X-Radiation protection, replace picture tube with original type or Hitachi approved equivalent type.

This Service Manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified

technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex

products such as those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability of the product and may void warranty. If you

are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the

repair to a qualified service technician.

WARNING

Lead in solder used in this product is listed by the California Health and Welfare agency as a known reproductive toxicant which

may cause birth defects or other reproductive harm (California Health and Safety Code, Section 25249.5).

When servicing or handling circuit boards and other components which contain lead in solder, avoid unprotected skin contact

with solder. Also, when soldering do not inhale any smoke or fumes produced.

This television receiver provides display of television closed captioning in accordance with section 15.119 of the FCC rules.

FEDERAL COMMUNICATIONS COMMISSION NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

¥ Reorient or relocate the receiving antenna.

¥ Increase the separation between the equipment and the receiver.

¥ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

¥ Consult the dealer or an experienced radio/television technician for help.

SAFETY NOTICE

USE ISOLATION TRANSFORMER WHEN SERVICING

High Voltage limiter circuit operation check.

1. Turn off TV and connect jig as shown in Figure 2. Adjust

jig fully counter-clockwise for minimum resistance.

2. Set the AC input to 120V AC and turn on TV.

3. Confirm test pattern on CRT is a usable picture, then

slowly adjust jig until the picture disappears and TV shuts

down.

4. When the limiter circuit is operating properly, High

Voltage will be less than 31.5 kV at 1.5mAwhen TV shuts

down.

5. Turn off set immediately after checking circuit operation.

6. Unplug set for one minute to reset shutdown circuit.

Remove jig and voltmeter.

TECHNICAL CAUTIONS

TP91 CP16 IP04

Remove RH80 and connect 50KΩVR jig as shown.

FBT

RH80

TP91

POWER/DEFLECTION PWB RH44

50K½VR

Chassis ground

High impedance

H.V. meter

Deflection P.W.B.

FBT

(TH01)

High voltage

connector

Fig. 2. Deflection/Power P.W.B.

Model: 43FDX01B

53FDX01B

Cathode-Ray Tube:

43FDX01B 53FDX01B

R=P16LTG00REA(U) R=P16LFM00RFA(LU)

G=P16LTG00HHA(U) G=P16LFM00HHA(LU)

B=P16LTG00BMB(U) B=P16LFM00BMB(EU)

Power Input: 120 volts AC, 60 Hz

Power Consumption:

43FDX01B 53FDX01B

245 Watts - Maximum 236 Watts - Maximum

217 Watts - Operating 208 Watts - Operating

Antenna Impedance: 75 Ohm Unbalanced

VHF / UHF / CATV

Receiving Channel: BAND CH

VHF 2~13

UHF 14~69

EXT. Mid (A-5)~(A-1), 4+

CATV Mid. A~I

CATV Super J~W

CATV Hyper (W+1)~(W+28)

Intermediate Frequency: Picture l-F Carrier 45.75 MHz

Sound l-F Carrier 41.25 MHz

Color Sub Carrier 42.17 MHz

Video Input: 1 Volt p-p, 75 Ohm

1 Volt p-p, 75 Ohm (Y)

0.7 Volt p-p, 75 Ohm, (PB, PR)

Video Output: 1 Volt p-p, 75 ohm

Audio Input: 470 mVrms, 47 k Ohm

Stereo Audio Output: 470 mVrms, 1 k Ohm

Audio Output Power:

Front: 12 watts per channel at 10% distortion,

8 ohm Impedance. Max output Ð 15 watts.

Anode Voltage: 30 ± 1.5kv (1.5±0.2mA)

Brightness: 43FDX01B 250 cd/m2

(white screen) 53FDX01B 170 cd/m2

Speakers: 2 Speakers - 5 inch (120 mm) round

Dimension: 43FDX01B 53FDX01B

Height (in.) 43 5/851 25/32

Width (in.) 39 46

Depth (in.) 20 25 1/2

Weight (Ibs.) 145 216

Circuit Board Assemblies:

C.P.T. (B) P.W.B. Terminal P.W.B.

C.P.T. (G) P.W.B. VM P.W.B.

C.P.T. (R) P.W.B. Surround P.W.B.

Audio Out P.W.B. Power/Deflection P.W.B.

2 H P.W.B. Control P.W.B.

Power Supply P.W.B. Control Sub P.W.B.

Signal P.W.B. Sensor Distribution P.W.B.

Sub Deflection P.W.B.

CIRCUIT PROTECTION

CAUTION: Below is an EXAMPLE only. See Replacement Parts List for details. The following symbol near the fuse

indicates fast operation fuse (to be replaced). Fuse ratings appear within the symbol.

125V

6 A 125V

Example:

SPECIFICATIONS

ÒRISK OF FIRE - REPLACE FUSE AS MARKEDÓ

The rating of fuse F901 is 6.0A - 125V.

Replace with the same type fuse for continued protection

against fire.

CONVERGENCE

ADJUST

POWER INPUT

EXIT MENU

VOL+VOL-

CH-

CH+

TV/Video

Source Selector

햲

햳햴

햶

햷

햵

MONITOR

OUT

INPUT 2

INPUT 1

AUDIO

(MONO) L

AUDIO

S-VIDEOS-VIDEO

VIDEO VIDEO

ANT A

CONVERTER

ANT B

AUDIO

(MONO)

S-VIDEO

VIDEO

AUDIO

TO HI-FI

GENERAL INFORMATION

Fig. 3. Front Control Panel

Fig. 4. Rear Panel Jacks

햲Antenna Input/Output 햵Audio to Hi-Fi

햳Audio/Video Inputs 1, 2 햶S-Video Inputs 1 and 2

햴Monitor Out 햷Component Inputs Y-PBPR

VIDEO

Select VIDEO to adjust picture settings and improve picture quality.

Use this function to change the contrast between black and white levels in the picture. This adjust-

ment will only affect the picture when ADVANCED SETTINGS ULTRA AI is OFF.

Use the THUMB STICK 왖or 왔to highlight the function to be adjusted.

Press the THUMB STICK 왗or 왘to adjust the function.

Press EXIT to quit menu.

NOTES: 1. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT:

Y-PBPRInput jacks.

2. If you are using the COMPONENT VIDEO input jacks (Y-PBPR) and notice that the TINT and COLOR are

abnormal, check to make sure that COMPONENT SET-COLOR SYSTEM is set properly.

Use this function to adjust the level of color in the picture.

Use this function to adjust flesh tones so they appear natural. (See notes below.)

Use this function to adjust overall picture brightness.

Use this function to adjust the amount of fine detail in the picture.

When RESET is selected, press down on THUMB STICK 왘to return video adjustments to factory

preset conditions.

CONTRAST

COLOR

TINT

BRIGHTNESS

SHARPNESS

RESET

MENU TO MENU BAR TO QUIT EXIT MENU TO MENU BAR TO QUIT EXIT

100%

50%

THUMB

STICK

THUMB

STICK

100%

CONTRAST

1. CONTRAST

2. BRIGHTNESS

3. COLOR

4. TINT

5. SHARPNESS

6. RESET

7. ADVANCED

SETTINGS

SETUP CUSTOMIZE VIDEO AUDIO THEATER

CUSTOMIZED PICTURE AND SOUND ADJUSTMENTS

SET UP

Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the

proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be

precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called ÒconvergenceÓ.

Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the TV. If you move

your TV, or if, after a time, you notice color rings or halos around objects in the picture, you may want to converge (align) the colors.

Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the

green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes

should be directly over each other to produce the white lines.

To simplify convergence, HITACHI incorporates a feature to allow you to display a test pattern of 1 horizontal and 1 vertical line at the

center of the screen. Simply use the remote control to adjust the red and blue colors to match the green. When properly aligned, the

outputs of all three tubes should be directly over each other to produce the white lines.

To enter this adjustment mode, you may also select CONVERGENCE ADJ. from the Set Up menu. However, this will display a message

prompting you to press the front panel CONVERGENCE ADJ. button.

NOTES: 1. Only a momentary press of the CONVERGENCE ADJUST button is necessary to enter CONVERGENCE ADJUST

mode.

2. The color being adjusted will blink (red or blue) to indicate color you are adjusting.

3. To save your adjustment data into memory, press the front panel CONVERGENCE ADJUST button. If you do NOT

wish to save your adjustment data into memory, turn the TV OFF. When the TV is turned ON again, your old

convergence data will be restored.

CONVERGENCE ADJ.

Red

CONVERGENCE

ADJUST

Blue

CONVERGENCE

ADJUST

SELECT

THUMB

STICK

THUMB

STICK

Press the THUMB STICK 왖, 왔, 왗, 왘buttons to move the displayed color up, down, left, or right.

Press MENU to change the color you want to adjust.

Press the front panel CONVERGENCE ADJUST button when adjustment is done. This will save your adjustment into memory.

Select AUDIO to adjust the TV to your preference and to improve the sound quality.

AUDIO

This function controls the low frequency audio to all speakers.

Use THUMB STICK 왖or 왔to highlight the function to be adjusted.

Press THUMB STICK 왗or 왘to adjust the function.

When RESET is highlighted, press down on THUMB STICK to reset audio settings to factory conditions.

Press EXIT to quit menu.

NOTE: If BASS is selected you are adjusting BASS. The additional menu items TREBLE and BALANCE can be selected and

adjusted in the same manner.

This function controls the high frequency audio to all speakers.

This function will control the left to right balance of the TV internal speakers and the AUDIO TO HI FI output.

When RESET is selected, press down on THUMB STICK to return audio adjustments to factory preset con-

ditions.

BASS

BALANCE

RESET

TREBLE

MENU TO MENU BAR TO QUIT EXIT MENU TO MENU BAR TO QUIT EXIT

THUMB

STICK

THUMB

STICK 72%

50%

1. BASS

2. TREBLE

3. BALANCE

4. RESET

5. ADVANCED

SETTINGS

90%

50%

SETUP CUSTOMIZE VIDEO AUDIO THEATER

1. BASS

2. TREBLE

3. BALANCE

4. RESET

5. ADVANCED

SETTINGS

DVD Player

Stereo System Amplifier

Laserdisc player, VCR,

camcorder, etc.

VCR #2

Cable TV Box

VCR #1

Outside antenna or

cable TV coaxial cable

2-Way signal splitter

OUTPUT

Y PBPRL R

HDTV Set-Top Box

V L R

OUTPUT

S-VIDEO

ANT

OUTPUT

S-VIDEO VL R

OUTPUT

B/CBPR/CR

L R

INPUT

V L R

INPUT

S-VIDEO

MONITOR

OUT

INPUT 2

INPUT 1

AUDIO

(MONO) L

AUDIO

S-VIDEOS-VIDEO

VIDEO VIDEO

ANT A

CONVERTER

ANT B

AUDIO

(MONO)

S-VIDEO

VIDEO

AUDIO

TO HI-FI

INPUT

OUTPUT

NOTE: 1. Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

TYPICAL FULL-FEATURE SETUP

CONNECTING A STEREO LASERDISC/DVD PLAYER OR HDTV SET TOP BOX TO INPUT 1 OR 2 COMPONENT: Y-PBPR.

1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV

set below.

2. Connect the cable from the CB/PBOUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack.

3. Connect the cable from the CR/PROUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack.

4. Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

5. Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

6. Press the INPUT button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO icon

disappears automatically after approximately eight seconds.

7. Press the INPUT button to return to the previous channel.

ANT A

CONVERTER

ANT B

PB/CB

PR/CR

PB/CB

PR/CR

MONITOR

OUT

INPUT 2

INPUT 1

AUDIO

(MONO) L

AUDIO

S-VIDEOS-VIDEO

VIDEO VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

AUDIO

TO HI-FI

Rear Panel of Television

OUTPUT

Y CBCR

R L

AUDIO VIDEO

DVD Player

Hitachi Model or

Similar Model

Back of

DVD Player

OUTPUT

Y PBPR

HDTV Set-Top Box

L R

NOTE: Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

CONNECTING EXTERNAL VIDEO SOURCES

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Téléviseur à projection

Hitachi

Hitachi 42V52 Manuel utilisateur

Hitachi

Hitachi 50UX57B Manuel utilisateur

Hitachi

Hitachi 51SWX20B Manuel utilisateur

Hitachi

Hitachi 62VS69 - UltraVision VS69 Series Manuel utilisateur

Hitachi

Hitachi 55DMX01WD Manuel utilisateur

Hitachi

Hitachi 43FDX10B Manuel utilisateur

Hitachi

Hitachi 50VF820 - 50" Rear Projection TV Manuel utilisateur

Hitachi

Hitachi 43GX10B Manuel utilisateur

Hitachi

Hitachi 46F510 Manuel utilisateur

Hitachi

Hitachi 53SWX01W Manuel utilisateur

Hitachi

Hitachi 50VS810 - 50" Rear Projection TV Manuel utilisateur

Hitachi

Hitachi C43-FD2000 Manuel utilisateur

Hitachi

Hitachi 50V525E - LCD Projection TV Manuel utilisateur

Hitachi

Hitachi 46GX01B Manuel utilisateur

Hitachi

Hitachi 53UWX10B Manuel utilisateur

Hitachi

Hitachi 53SBX10B Manuel utilisateur

Hitachi

Hitachi 43FDX20B Manuel utilisateur

Hitachi

Hitachi 50EX14BV Manuel utilisateur

Hitachi

Hitachi 50FX18B Manuel utilisateur

Hitachi

Hitachi 42V515 - 42" Rear Projection TV Manuel utilisateur

Hitachi

Hitachi 46UX51K Manuel utilisateur

Hitachi

Hitachi 70VS810 - 70" Rear Projection TV Manuel utilisateur

Hitachi

Hitachi 50EX20B Manuel utilisateur

Hitachi

Hitachi 50EX11BV/12KV Manuel utilisateur

Manuels Téléviseur à projection populaires d'autres marques

Samsung

Samsung ST-43T6P Manuel utilisateur

Toshiba

Toshiba ColorStream TP50G60 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WD-65734 Manuel utilisateur

Optoma

Optoma EP652A Manuel utilisateur

Samsung

Samsung SP43T8HPX/XEC Manuel utilisateur

Philips

Philips 28PW6006 - annexe 1 Manuel utilisateur

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Guide de l'utilisateur

Philips

Philips 43PP8421 Manuel utilisateur

RCA

RCA P52950 Manuel utilisateur

Sony

Sony KP-51DS1U Manuel utilisateur

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Manuel utilisateur

Pioneer

Pioneer Elite PRO 510HD Manuel utilisateur

Philips

Philips 43PP8421 Manuel

JVC

JVC I'Art Pro AV-48P776 Manuel utilisateur

Sony

Sony GRAND WEGA KDF-55XS955 Manuel utilisateur

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Manuel utilisateur

Toshiba

Toshiba 42HM66 - 42" Rear Projection TV Manuel utilisateur

Philips

Philips 50PL9200D Manuel utilisateur