Hitachi L200 Series Guide de démarrage rapide

Hitachi America, Ltd.

EN-050202-1

ENGINEERING NOTE

SUBJECT: ANALOG VOLTAGE INPUT CALIBRATION ERROR

AFFECTED

MODELS: L200 and SJ200 – MFG DATE 0501 & BEFORE

Certain models of L200 and SJ200 were inadvertently shipped with the 0 – 10

Volt Analog Input (terminal O – L) span parameter improperly calibrated.

The symptom is easily determined. The inverter will operate properly with a

frequency reference from keypad potentiometer, analog 4 – 20 mA input or F001

setting. However when the frequency reference is set to the O voltage input, the

inverter will act erratically at 0 V input, and may trip on overcurrent. The output

frequency will ramp up linearly from 0 V to approximately 0.2 V input with a

corresponding output frequency of 0 to the maximum (factory default is 60 Hz)

frequency. From input voltages from 0.2 V to 10.0 V, the inverter output will

remain pegged at the maximum frequency.

To correct this problem, first stop the inverter. Then follow these steps:

1. Press FUNC to enter the PROGRAM mode.

2. Using the UP / DN arrow keys, navigate to parameter C091.

3. Press FUNC to view the contents, and press UP arrow key to change the

value to 01

4. Press STR to save the change. This will make the so-called “debug”

parameters accessible.

5. Using UP arrow key, navigate to parameter C121

6. Press FUNC to view contents. It most likely is 6553

PGC - 2/2/05 Page 1 of 2

7. Using the DN arrow key, change the value to 1100.(Note the decimal

point after the number - this is critical!!) As you decrement the parameter

value, you will scroll past 1100 (WITHOUT a decimal point!!) Continue

going down toward zero, and the sequence will start again at 9999.

(WITH decimal point after!) and continue decrementing from there.

8. Continue down until the display reaches 1100.Press STR to save the

value. The display should show C121 again.

9. Navigate with the DN arrow key to C091 and press FUNC again.

10.Change setting from 01 back to 00 with DN arrow key. Press STR

again to save. Display again should read C091

11.Press FUNC TWICE until display reads C---

12.Press UP arrow key until you reach o001

13.Press FUNC, then STR This step re-establishes the output frequency

display as the power-on default display.

The analog voltage input should now operate linearly with a 0 – 10 V input

corresponding to a 0 – 60 Hz output.

PGC - 2/2/05 Page 2 of 2

Autres manuels pour L200 Series

5

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Hitachi Onduleur

Hitachi

Hitachi L300P Series Manuel utilisateur

Hitachi

Hitachi SJ200 Series Manuel utilisateur

Hitachi

Hitachi air core 600 Mode d’emploi

Hitachi

Hitachi X200 Series Manuel d'instructions

Hitachi

Hitachi SJ100 Series Manuel utilisateur

Hitachi

Hitachi SJ200 Series Manuel utilisateur

Hitachi

Hitachi L300P Series Manuel utilisateur

Hitachi

Hitachi J300 Series Mode d’emploi

Hitachi

Hitachi WJ200-004M Manuel utilisateur

Hitachi

Hitachi WJ200-001S Manuel utilisateur

Hitachi

Hitachi J300 Series Manuel utilisateur

Hitachi

Hitachi SJ100 Series Manuel utilisateur

Hitachi

Hitachi SJ700-2 Series Manuel utilisateur

Hitachi

Hitachi SJ100 Series Manuel du propriétaire

Hitachi

Hitachi SJ2002 Series Manuel utilisateur

Hitachi

Hitachi SJ700-2 Series Manuel utilisateur

Hitachi

Hitachi WL200 Series Guide d'installation

Hitachi

Hitachi SJ100 Series Instructions d'installation et d'utilisation

Hitachi

Hitachi WJ200 Series Software Manuel utilisateur

Hitachi

Hitachi L100-004HFE Manuel utilisateur

Hitachi

Hitachi SJ-LW Manuel utilisateur

Hitachi

Hitachi S1 Series Guide de l'utilisateur

Hitachi

Hitachi P1 Guide d'installation

Hitachi

Hitachi SJ700-4000HFU2 Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur