Hitachi HF-W100E Manuel utilisateur

First Edition, October 2017, WIN-62-0069 (out of print)

Second Edition, November 2017, WIN-62-0069-01

The contents of this publication may be revised without prior notice.

No part of this publication may be reproduced in any form or by any means without permission in

writing from the publisher.

Printed in Japan.

This Page Intentionally Left Blank

PREFACE

This manual is intended for operators of the HITACHI INDUSTRIAL COMPUTER HF-W100E

(hereafter called as this equipment) contains information about the operation and maintenance of

various equipment necessary for their routine work. And also this manual describes the setup

procedure of the OS installed in this equipment, namely the following pre-installed OS.

・Windows® Embedded Standard 7

・Windows® 10 IoT Enterprise

SEPARATE VOLUME CONSTITUTION

The manual of the HITACHI INDUSTRIAL COMPUTER HF-W100E consists of the following:

・SAFETY INSTRUMENTS

・INSTRUCTION MANUAL (This manual)

・RAS FEATURES MANUAL

MANUAL CONSTITUTION

This manual consists of the following:

PREFACE

IMPORTANT NOTIFICATION

SAFETY INSTRUCTIONS

PRECAUTIONS

CHAPTER 1 GETTING STARTED

CHAPTER 2 OPERATION

CHAPTER 3 SETUP

CHAPTER 4 PRECAUTIONS REGARDING THE OS

CHAPTER 5 SPECIFICATIONS

CHAPTER 6CHECKUP AND MAINTENANCE

CHAPTER 7RESTORING THE FACTORY-SHIPPED CONDITION USING

A RECOVERY DVD

CHAPTER 8MAINTENANCE OPERATIONS

CHAPTER 9TROUBLESHOOTING

APPENDIX HANDLING REPLACEABLE COMPONENTS

[Trademarks]

•Microsoft®, Windows®, Internet Explorer® are registered trademarks of U.S. Microsoft

Corporation in the United States and other countries.

•Intel®, Intel® AtomTM are trademarks of Intel Corporation in the United States and other

countries.

•CFastTM is a registered trademark of Compact Flash Association.

•DisplayPort and DisplayPort Certified Logo are registered trademarks of Video Electronics

Standards Association.

•Magic Packet™ is a trademark or a registered trademark of Advanced Micro Devices, Inc.

•Ethernet is a registered trademark of Fuji Xerox Co., Ltd.

•EtherCAT is a patented technology licensed by Beckhoff Automation GmbH, Germany and is a

registered trademark.

•CODESYS® is a registered trademark of 3S-Smart Software Solutions GmbH.

•All other product names (software and hardware) not from Hitachi described in this manual are

the registered trademarks, the trademarks, or the products of their respective owners.

•Zlib is used as a compression and decompression engine built in a part of the software of this

product. Its copyright notice is as follows:

iii

IMPORTANT NOTIFICATIONS

• The contents of this manual cannot be copy without permission.

• The contents of this manual are subject to change without notice.

NOTICE

Depending on the type of failure, important files may be lost when you use this

equipment. Files can be lost by power failure and human mistakes during

operation in addition to the failure of the equipment. If such a situation occurs,

the files cannot be recovered. In order to prevent data loss, make it a routine to

save your files and establish a systematic schedule for backing up files.

●Harmonic Current Standards

This equipment is compliant with the IEC/EN 61000-3-2 Power supply Harmonic Standard.

●VCCI Notice

This is a Class A product based on the standard of the Voluntary Control Council for

Interference by Information Technology Equipment (VCCI). Using this equipment in a

residential environment may cause radio disturbance. In this case, the user may be required to

take appropriate measures.

[Note for storage capacity calculations]

●Memory capacities and requirements, file sizes and storage requirements, etc. must be

calculated according to the formula 2n. The following examples show the results of such

calculations by 2n(to the right of the equals signs).

1 KB (kilobyte) = 1,024 bytes

1 MB (megabyte) = 1,048,576 bytes

1 GB (gigabyte) = 1,073,741,824 bytes

1 TB (terabyte) = 1,099,511,627,776 bytes

●As for disk capacities, they must be calculated using the formula 10n. Listed below are the

results of calculating the above example capacities using 10nin place of 2n.

1 KB (kilobyte) = 1,000 bytes

1 MB (megabyte) = 1,0002bytes

1 GB (gigabyte) = 1,0003bytes

1 TB (terabyte) = 1,0004bytes

●This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

●이기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이점을

주의하시기 바라 며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.

This equipment conforms to the electromagnetic wave for Industrial use (Class A).Vender or

user should take notice and use the purpose except for household use.

●警告使用者：此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，

在此種情況下，使用者會被要求採取某些適當的對策。

[Terms used in this manual]

Terms used in this manual are defined as follows.

・Install: An operation of installing software programs in the computer’s mSATA SSD

・Setup: An operation of setting an environment so that the software can use in the computer

[Rereading terms]

This manual describes the Windows® operating procedure. Names of operations “sign in”

and “sign out” are replaced with “log on” and “log off” respectively depending on

Windows® types. Reread them as required.

S-1

SAFETY INSTRUCTIONS

Carefully read and fully understand the safety precautions below before operating

the equipment.

Operate the equipment by following the instructions and procedures described

in this manual.

Pay attention especially to safety precautions displayed on the equipment or in

this manual. Make sure you follow them. Otherwise, personal injury and

property damage including damage to the equipment may result.

A safety precaution is indicated by a heading as shown below. A heading is

either a safety alert symbol; a word such as “DANGER”, “WARNING”,

“CAUTION”, or “NOTICE”; or a combination of both.

This is a safety alert symbol. This symbol is used to signify

potential hazards that may result in personal injury or death.

Make sure you follow the safety message that follows this

symbol in order to avoid possible injury or death.

DANGER:This symbol is used to indicate imminent hazards that

will highly likely result in serious personal injury or

death.

WARNING:This symbol is used to indicate potential hazards that

may result in serious personal injury or death.

CAUTION:This symbol is used to indicate potential hazards that

may result in minor or moderate personal injury.

NOTICE: This symbol is used to indicate hazards that may result in

equipment or property damage but not personal injury.

The heading “NOTE” is used to indicate a cautionary note about handling and

operation of the equipment.

Do not attempt to perform any operation that is not described in this manual. If

there is any problem with the equipment, call your maintenance personnel.

Read this manual carefully and fully understand the directions and precautions

written in this manual before operating the equipment.

Keep this manual nearby so that you can reference the manual anytime you

need it.

Every effort has been made to specify the best precautions on the equipment

and in the manual. Nevertheless, unexpected incidents may occur. When you

use the equipment, you are asked not only to follow the instructions but also to

use your own judgment on safety.

S-2

SAFETY INSTRUCTIONS (Continued)

1. COMMON SAFETY PRECAUTIONS

Carefully read and fully understand the following safety precautions.

1.1 WARNING

This equipment is not designed and manufactured to be used for a life-critical

system that requires extreme safety. If there is a possibility that the equipment

may be used for this purpose, contact relevant sales representatives.

In case of smoke, a burning smell, or the like, unplug the power cable from

the outlet, disconnect the power cable from the outlet, and contact your

supplier or maintenance personnel. Using the faulty equipment without repair

may result in a fire or an electric shock.

Do not modify this equipment because that may result in a fire or an electric

shock. If you do not, serious injury or death may result due to the equipment

failure. The Manufacturer’s responsibility is exempted from any result

arising out of the user’s modification of the Equipment.

Fire and electric shock or burn by heat may occur. When using the optional

AC adapter, please be used with caution in the following.

・Never disassemble.

・Do not use in high humidity place. Also, do not wet with water or

touch with wet hands.

・Do not use in dusty place.

・Do not use or leave this equipment in an environment where heat is

stucked.

・Do not put anything on top.

・Make sure to connect the ground wire to the ground terminal of the

equipment when the user independently prepares a power supply unit and

a DC power cable without using the optional AC adapter and the attached

AC power cable. Also, use this equipment after fully performing the

operation verification by the user-self.

In addition, install an earth leakage circuit breaker together. If you do not,

fire or electric shock may result.

Table des matières

Autres manuels Hitachi PC industriel

Hitachi

Hitachi HF-W7500 Manuel utilisateur

Hitachi

Hitachi HF-W6500 45/40 Manuel du propriétaire

Hitachi

Hitachi HF-W6500 Manuel utilisateur

Hitachi

Hitachi HF-W6500 45/40 Manuel utilisateur

Hitachi

Hitachi HF-W6500 60 Manuel utilisateur

Hitachi

Hitachi HF-W7500 65 Manuel du propriétaire

Hitachi

Hitachi HF-BT1000 Manuel utilisateur

Hitachi

Hitachi HF-W7500 40 Manuel utilisateur

Hitachi

Hitachi HF-W2000 58 Manuel utilisateur

Hitachi

Hitachi CSNET MANAGER XT Manuel utilisateur

Manuels PC industriel populaires d'autres marques

Chipsee

Chipsee PPC-A72-101 Manuel utilisateur

Advantech

Advantech UNO-2184G Manuel utilisateur

MSI

MSI MS-9A76 Manuel utilisateur

Stackrack

Stackrack THOR200 Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682C Series Manuel utilisateur

Nodka

Nodka eBOX-3000-ETC Manuel utilisateur

Siemens

Siemens SIMATIC IPC627E Manuel utilisateur

MSI

MSI MS-9A89 Manuel utilisateur

Artila

Artila Matrix-516 Manuel utilisateur

Siemens

Siemens SIMATIC Rack PC 840 V2 Manuel utilisateur

Advantech

Advantech IPPC-6152A Manuel utilisateur

Beckhoff

Beckhoff CX9020 Manuel utilisateur

Dell

Dell Embedded Box PC 5000 Manuel utilisateur

IBASE Technology

IBASE Technology ASB200-918 Series Manuel utilisateur

Lenovo

Lenovo ThinkCentre M90q Manuel du propriétaire

IXXAT

IXXAT Econ 100 Manuel utilisateur

Kontron

Kontron KBox A-151-TGL Manuel utilisateur

AXIOMTEK

AXIOMTEK ICO500-518 Series Manuel utilisateur