Hitachi S10mini LQS070 Manuel utilisateur

First Edition, December 1998, SME-1-104(A) (out of print)

Second Edition, October 2008, SME-1-104(D)

The contents of this publication may be revised without prior notice.

No part of this publication may be reproduced in any form or by any means without permission

in writing from the publisher.

Printed in Japan.

BI-KB-KO<IC-IC> (FL-MW20, AI8.0)

SAFETY PRECAUTIONS

Be sure to read this manual and all other attached documents carefully before installing,

operating inspecting or conducting maintenance on this unit. Always use this unit properly.

Be sure to carefully read the information about the device, the safety information and precautions

before using this unit. Be sure that the person(s) responsible for maintenance receives and

understands this manual completely.

This manual divides the safety precautions into DANGERs and CAUTIONs.

: Failure to observe these warnings may result in death or serious injury.

: Failure to observe these cautions may result in injury or property

damage.

Failuretoobserveany may lead to serious consequences.

All of these DANGERs and CAUTIONs provide very important precautions and should

always be observed.

Additional safety symbols representing a prohibition or a requirement are as follows:

: Prohibition. For example, “Do not disassemble” is represented by:

: Requirement. For example, if a ground is required, the following will be shown:

DANGER

CAUTION

1. Installation

CAUTION

 Use this product under the environmental conditions specified in the catalogs

and manual.

Utilizing this product in a hot, damp, or dusty atmosphere or in an atmosphere

of corrosive gas, vibration or impact may lead to a malfunction, shock hazard

or fire.

 Install this product according to the procedure outline in the manual.

Imperfect installation may lead to a part drop, failure or malfunction.

 Do not put any wire chip or other foreign matter into this product.

This may cause a malfunction, failure or fire.

2. Wiring

REQUIREMENT

 Be sure to ground this product with FG.

Failure to ground this product may lead to a malfunction or shock hazard.

CAUTION

 Connect this product to a power supply with the same ratings.

Connecting this product to a power supply exceeding its voltage rating may

lead to a fire.

 Wiring must be conducted by a qualified technician.

Miswiring may lead to failure, shock hazard or fire.

 Wiring by transceiver cables and coaxial cables must be separated from wiring

from high-voltage equipment. Combining these two systems of wires in one

place may lead to a malfunction.

3. Handling precautions

DANGER

 Do not touch any terminal while this product is live, as this may lead to a shock

hazard.

 Configure an emergency stop circuit, interlocking circuit and related circuitry

outside the programmable controller.

A programmable controller failure may lead to a general breakdown or an

accident.

CAUTION

 Make sure that everything is safe before changing programs, running or

stopping this product while on the fly or producing forced output.

Mishandling may lead to product breakdown or an accident.

 Turn on the product according to the correct power - on procedure.

Mishandling may lead to product breakdown or an accident.

 Do not use a transceiver, mobile phone, or the like near this module. Using

such a device nearby may lead to a malfunction or a module failure due to

electrical noise.

4. Maintenance

PROHIBITION

Do not disassemble or remodel this product, as this may lead to a malfunction,

failure or fire.

CAUTION

Power off this product before attaching or detaching any module or unit as this

may lead to a malfunction, failure or shock hazard.

WARRANTY AND SERVICING

Unless a special warranty contract has been arranged, the following warranty is applicable to this

product.

1. Warranty period and scope

Warranty period

The warranty period for this product is for one year after the product has been delivered to the

specified delivery site.

Scope

If a malfunction should occur during the above warranty period while using this product under

normal product specification conditions as described in this manual, please deliver the

malfunctioning part of the product to the dealer or Hitachi Engineering & Services Co., Ltd.

The malfunctioning part will be replaced or repaired free of charge. If the malfunctioning is

shipped, however, the shipment charge and packaging expenses must be paid for by the

customer.

This warranty is not applicable if any of the following are true.

 The malfunction was caused by handling or use of the product in a manner not specified in

the product specifications.

 The malfunction was caused by a unit other than that which was delivered.

 The malfunction was caused by modifications or repairs made by a vendor other than the

vendor that delivered the unit.

 The malfunction was caused by a relay or other consumable which has passed the end of its

service life.

 The malfunction was caused by a disaster, natural or otherwise, for which the vendor is not

responsible.

The warranty mentioned here means the warranty for the individual product that is delivered.

Therefore, we cannot be held responsible for any losses or lost profits that result from the

operation of this product or from malfunctions of this product. This warranty is valid only in

Japan and is not transferable.

2. Range of services

The price of the delivered product does not include on-site servicing fees by engineers.

Extra fees will be charged for the following:

 Instruction for installation and adjustments, and witnessing trial operations.

 Inspections, maintenance and adjustments.

 Technical instruction, technical training and training schools.

 Examinations and repairs after the warranty period is concluded.

 Even if the warranty is valid, examination of malfunctions that are caused by reasons

outside the above warranty scope.

This manual provides information for the following hardware product:

J.NET (LQE040)

Description of added changes Page

Supplementary, “Replacing or adding on the module” is newly added. Z-1

In addition to the above changes, all the unclear descriptions and typographical errors found are also

corrected without prior notice.

Revision record

Revision No. Revision Record (revision details and reason for revision) Month, Year Remarks

A First Edition December 1998

D Supplementary, “Replacing or adding on the module” is

newly added.

October 2008

PREFACE

We greatly appreciate your purchase of the J.NET module — an option for the CPU. This manual

describes how to operate the J.NET module. We request that you read this manual carefully to

ensure the correct use of the J.NET module.

Autres manuels pour S10mini LQS070

Table des matières

Autres manuels Hitachi Contrôleurs

Hitachi

Hitachi ECO COMPACT PC-ARC-E Manuel utilisateur

Hitachi

Hitachi SJ-P1 Series Manuel utilisateur

Hitachi

Hitachi CMU Series Manuel utilisateur

Hitachi

Hitachi MICRO-EHV+ Instructions d'utilisation

Hitachi

Hitachi Eco Compact PC-ARC-A Mode d’emploi

Hitachi

Hitachi HD64465 Manuel utilisateur

Hitachi

Hitachi HIDIC EH-150 EH-PT4 Instructions d'utilisation

Hitachi

Hitachi EH-RMP2 Instructions d'utilisation

Hitachi

Hitachi HIDIC MICRO-EH Instructions d'utilisation

Hitachi

Hitachi EHV+ Series Instructions d'utilisation

Hitachi

Hitachi H8/3637 Manuel utilisateur

Hitachi

Hitachi HIDIC EH-150 Instructions d'utilisation

Hitachi

Hitachi EH-150 Type I Instructions d'utilisation

Hitachi

Hitachi HIDIC EH-150 Instructions d'utilisation

Hitachi

Hitachi ATW-YCC-03 Manuel utilisateur

Hitachi

Hitachi EH-150 Type I Instructions d'utilisation

Hitachi

Hitachi HIDIC EH-150 Instructions d'utilisation

Hitachi

Hitachi FL.NET Manuel utilisateur

Hitachi

Hitachi EH-150 Series Instructions d'utilisation

Hitachi

Hitachi PSC-A64S Manuel utilisateur

Hitachi

Hitachi Eco Compact PC-ARC-A Manuel utilisateur

Hitachi

Hitachi LQZ700 Manuel utilisateur

Hitachi

Hitachi PLC Manuel utilisateur

Hitachi

Hitachi CIS02-H Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur