Hisense WFU7012 Manuel utilisateur
WASHING MACHINE
SERVICE MANUAL
WFU7012&WFU7012S
WFUA7012&WFUA7012S
CAUTION
READ THIS MANUAL CAREFULLY TO DIAGNOSE
PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.
CONTENTS
1
CONTENTS
1. SAFETY NOTICES………………………………………………….…….…1
2. SPECIFICATIONS…………………………………………………………...3
3. FEATURES & TECHNICAL EXPLANATION…………………..………….4
3.1 FEATURES .......................................................................................... 3
3.2 INTELLIGENT FUZZY CONTROL ...................................................... 4
3.3 POWER SUPPLY CONTROL .............................................................. 4
3.4 WATER LEVEL CONTROL ................................................................. 5
3.5 DOOR LOCK CONTROL .................................................................... 5
3.6 LAUNDERING CONTROL .................................................................. 6
3.7 HEATING CONTROL .......................................................................... 7
3.8 SPINNING CONTROL ......................................................................... 7
4. PARTS IDENTIFICATION.....................................................................10
5. INSTALLATION AND TEST...................................................................11
5.1 STANDARD INSTALLATION ............................................................. 10
5.2 CONNECT THE INLET HOSE .......................................................... 11
5.3 CONNECT THE DRAIN HOSE ......................................................... 11
5.4 CONNECT POWER PLUG ............................................................... 11
5.5 TEST OPERATION ............................................................................ 11
6. OPERATION.........................................................................................14
6.1 CONTROL PANEL ............................................................................. 13
6.2 CYCLE GUIDE .................................................................................. 14
6.3 COMMON FUNCTIONS .................................................................... 16
6.4 ADDITIONAL FUNCTIONS ............................................................... 18
7. WIRING DIAGRAM/PROGRAM CHART...............................................22
7.1 WIRING DIAGRAM ........................................................................... 21
CONTENTS
2
7.2 PROGRAM CHART ........................................................................... 23
8. TEST MODE.........................................................................................25
8.1 SELF-INSPECTION MODE ............................................................... 24
8.2 SPECIAL FUNCTION MODE ............................................................ 26
9. TROUBLESHOOTING..........................................................................29
9.1 SAFETY CAUTION ........................................................................... 28
9.2 ERROR MODE SUMMERY .............................................................. 28
9.3 TROUBLESHOOTING WITH ERROR .............................................. 30
9.4 TROUBLE SHOOTING ELSE ........................................................... 36
10. COMPONENT TESTING INFORMATION..........................................40
10.1 FILTER ............................................................................................ 39
10.2 DOOR LOCK ................................................................................... 40
10.3 MOTOR ........................................................................................... 41
10.4 PUMP .............................................................................................. 42
10.5 INLET VALVE .................................................................................. 43
10.6 HEATER .......................................................................................... 44
11. DISASSEMBLY INSTRUCTIONS.......................................................46
11.1 CONTROL PANEL ASM .................................................................. 45
11.2 DISPENSER ASM ........................................................................... 46
11.3 FILTER ............................................................................................. 47
11.4 DOOR ASM ..................................................................................... 48
11.5 FRONT PANEL ................................................................................ 49
11.6 PUMP .............................................................................................. 50
11.7 HEATER .......................................................................................... 50
11.8 MOTOR ........................................................................................... 51
1. SAFETY NOTICES
1
• Cut off the power first before maintaining and
repairing the washing machine.
• It is for preventing from harms duet to electric
leakage.
• Please do not sprinkle or spray water directly
to any part of the washing machine during
maintenance and repair.
• Otherwise, accidents like short circuit or
electric shock may happen.
• Please do not place the washing machine in
places where are damp or are exposed to wind,
rain and the sun.
• It is for preventing from fire accidents due to
electric shock or electric leakage.
Explosion Or Fire
• It is strictly prohibited to place the clothes
smeared with inflammables into the drum of
washing machine.
• It is for preventing from possible explosion or
fire accident.
Mechanical Injury
• Do not open the door in a forced way.
• It is for preventing from possible damage.
Safety Tips For Children
• Please do not let the children to use the
washing machine, and do not place rack,
stools, etc. around the washing machine.
• The children may suffer personal injury due
to they climbing the washing machine or
crawling into the drum.
The nut connecting water
inlet tube to the machine
must be screwed u
p
.
When the washing machine
is unused, please be sure to
turn off the faucet.
Please dismantle the door of
machine before discarding
and handlin
g
.
If the washing machine is
damaged during transportation,
please do not use it. Please
call the “After-sales Service
Personnel”.
2. SPECIFICATION
2
ITEM WFU7012& WFUA7012/ WFU7012S& WFUA7012S
COLOR WHITE/SILVER
POWER SUPPLY AC 220-240 V，50 Hz
PRODUCT WEIGHT 72 Kg
ELECTRIC POWER
CONSUMTION
WASHING 300 W
HEATER 1900 W
REVOLUTION
SPEED
WASH 55 rpm
SPIN 1200 rpm
CYCLES 15
WASH/RINSE TEMPERATURES 20-❉/30/40/60/95℃
SPIN SPEEDS 0/600/800/1000/1200 rpm
OPTIONS
Delay
、
Eco wash
、
Prewash
、
Rinse hold
、
Extra rinse
、
Intensive wash
、
Mute Function
、
Child lock
WATER CIRCULATION 0.1-1 MPa
CONTROL TYPE Electronic
Washing Capacity 7 Kg
Dimension 595 X600 X 850 mm
DELAY WASH up to 24 hours
DOOR LOCK TYPE PTC
WATER LEVEL FWL Sensor control
LAUNDRY LOAD SENSING Incorporated（Cotton、Synthetics）
ERROR DIAGNOSIS Incorporated
AUTO POWER OFF Incorporated
3. FEATURES & TECHNICAL EXPLANATION
3
3.1 FEATURES
■ Ultra Capacity
The larger drum enables not just higher head drop and
stronger centrifugal force, but also less tangling and wrinkling
of the laundry. Heavier loads, such as king size comforters,
blankets, and curtains, can be washed.
■ Automatic Wash Load Detection
Automatically detects the load and optimizes the washing
time.
■ Built-in Heater
Internal heater helps to maintain water temperature at its
optimum level for selected cycles.
■ Child Lock
The Child lock prevents children from pressing any button to
change the settings during operation.
3. FEATURES & TECHNICAL EXPLANATION
4
3.2 INTELLIGENT FUZZY CONTROL
In order to achieve the best washing effects, it is necessary to determine the
optimum time and washing water level based on the water supply conditions.
3.3 POWER SUPPLY CONTROL
♦ After the washing machine is energized, the PCB is under “Off mode”, and all
buttons and knobs except for the “ON/OFF” button are disabled; all loads are in
the state of ready-for-activating.
♦ After pressing the “ON/OFF” button, the PCB will switch to “Ready mode” from
“Off mode”, and conduct status inquiry for minutes, with values of parameters
like water level, water temperature, air temperature, motor speed, door lock
state, etc. obtained.
♦ When the PCB runs a complete routine to end, the “Ready mode” will display
the previous completed program, with the settings corresponding to those set
by default. If the previous flow that is not run to end, then it will restore to the
“Cotton” program by default.
• washing program
• Water supply
Sensing
• Intelligence
fuzzy
Handling
• washing time
• water level
Adjust
3. FEATURES & TECHNICAL EXPLANATION
5
♦ When the program finishes and displays “End”, the door will be unlocked, and
the PCB will enter in “End mode”.
♦ If no button-press operation is done for 3 minutes when the washing machine
is under “Ready mode”, the PCB will automatically be power off and switch to
“Off mode”. If no button-press operation is done for 30 seconds when the
washing machine is under “End mode” where the washing is completed, the
PCB will automatically be power off and switch to “Off mode”.
♦ In order to avoid the user to falsely triggering the “ON/OFF” button, two
successive seconds are required for switching from “On mode” to “Off mode”,
and only one click is required for switching from “Off mode” to “On mode”.
3.4 WATER LEVEL CONTROL
♦ This module contains a FWL sensorfor detecting the water level of tub.
♦ During water inflowing, the PCB controls the inlet valve to function and execute
the water inflow operation. When the water level reaches the “Washing water
level”, the water inflow stops and the washing process begins. If the water level
declines during washing, it will automatically activate the water inflow and
replenishing program so as to reach the “Washing water level” again.
♦ During water draining, the PCB controls the draining pump to continuously
work and begin the water draining process. When the water of tub is discharged
down to the “Spinning water level”, the Spinning process will begin.
3.5 DOOR LOCK CONTROL
♦ When the PCB enters in “Ready mode”, it will detect the state of door lock and
execute operation accordingly. When the door is unlocked, no operation is done
if the unlocking conditions are satisfied, otherwise, the door should be locked;
when the door is locked, execute unlocking operation if the unlocking conditions
3. FEATURES & TECHNICAL EXPLANATION
6
are satisfied, otherwise, the door should be maintained locked.
♦ After selecting the program and function, press the “Start/Pause” button, the
PCB controls the door lock to execute locking operation, and the “Door lock”
icon on display window is on.
♦ After the program ends, the “Door lock” icon on display window is flickering
when the unlocking conditions are satisfied, and the PCB controls the door lock
to execute unlocking operation. When the “Door lock” icon on display window is
off, the door is unlocked.
♦ The program enters in “Pause mode” from “Run mode”, and the unlocking
operation can be executed if conditions permit.
♦ In case of power outage during washing, the door will be unlocked 3 min later
(the specific time depends on the different ambient temperature).
♦ The door lock clicks when it executes the program of “lock/unlock”.
♦ Door unlocking conditions: the motor stops, the water temperature is below
50°C, and the water level is below the “Door-opening water level”.
3.6 LAUNDERING CONTROL
♦ After the PCB enters in the “Ready mode”, select proper program and function,
press down “Start/Pause” button, and the PCB controls the door lock to lock,
controls the inlet valve for water inflowing up to the “washing water level”, and
then begins the laundering process.
♦ The PCB controls the motor to execute intermittent operations in clockwise
and counterclockwise directions at a constant frequency, driving the drum to
rotate via belt sheave for purpose of laundering.
♦ Motor speed and rotation/stop ratio under “Cotton” program:
3. FEATURES & TECHNICAL EXPLANATION
7
Course Water inflow Pre-wash Wash Rinse
Motor speed 45rpm 55rpm 55rpm 55rpm
Rotation/Stop ratio 10:5 20:10 20:10 12:8
3.7 HEATING CONTROL
♦ When the temperature set by the user is higher than the water temperature,
the PCB will control the heater to function and run the heating process until the
water temperature reaches the set temperature.
♦ When the temperature set by the user is higher than the water temperature,
no heating operation is required.
♦ The heater is enabled and proceeds to function until 3 seconds pass by after
the set temperature is reached.
♦ When the water level is below the “Heating water level”, the heater should be
forced to shut down, and then replenish water.
3.8 SPINNING CONTROL
♦ During draining, the Spinning process will begin after the water of tub is
discharged down to the “Spinning water level”.
♦ The PCB controls the motor to drive the drum to rotate in clockwise direction.
Carry out distribution measurement at low speed (about 110rpm) first, and then
measure the equilibrium value. After the equilibrium value is up to standard, the
distribution measurement succeeds, and enter the stage of high-speed
Spinning.If the distribution measurement fails as the equilibrium value is too big
and does not meet the requirements, then it is necessary to continuously carry
out distribution measurement operation.
♦ Spin speed limit: The spin speed shall neither exceed the maximum speed set
by the program nor exceed the speed manually set via the “Spin” button.
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Hisense Rondelle
Hisense
Hisense WFPV7012EMS Instructions de montage
Hisense
Hisense WDQY901418VJM Series Manuel utilisateur
Hisense
Hisense W921DJS Instructions de montage
Hisense
Hisense X08060026B Instructions de fonctionnement
Hisense
Hisense WFGE901439VM Instructions de montage
Hisense
Hisense WFER1014VA Instructions de montage
Hisense
Hisense WFQY8514VJM Manuel du propriétaire
Hisense
Hisense HWGE9014 Instructions de montage
Hisense
Hisense HWFR6510 Manuel utilisateur
Hisense
Hisense WFDJ60101 Instructions de montage
Hisense
Hisense 5S Series Instructions de montage
Hisense
Hisense WFU7012S Fiche d'information produit
Hisense
Hisense WFBJ90121 Manuel du propriétaire
Hisense
Hisense 3 Series Instructions de montage
Hisense
Hisense HWFV8012 Manuel du propriétaire
Hisense
Hisense WFPV9014EMT Instructions de montage
Hisense
Hisense HWFS8514E Instructions de montage
Hisense
Hisense WDBL1014V Manuel du propriétaire
Hisense
Hisense WF3M841BWI Instructions de montage
Hisense
Hisense HWFPV8012EMT Manuel du propriétaire
