Hirschmann TRS 05 Manuel utilisateur

www.hirschmann.com

P/N 031-300-190-199 Revision B 09/07/2006

DS 85 with TRS 05 / PATB3

TRS 05 Receiver/PATB3 Switch Replacement on the DS 85

Installation

NOTICE

Hirschmann makes no warranty of any kind with regard to this material, including, but not limited to,

the implied warranties of merchantability and/or its fitness for a particular purpose.

Hirschmann will not be liable for errors contained in this manual or for incidental or consequential

damages in connection with the furnishing, performance, or use of this manual. This document

contains proprietary information, which is protected by copyright, and all rights are reserved.

No part of this document may be photocopied, reproduced, or translated to another language without

the prior written consent of Hirschmann.

Hirschmann reserves proprietary rights to all drawings, photos and the data contained therein. The

drawings, photos and data are confidential and cannot be used or reproduced without the written

consent of Hirschmann. The drawings and/or photos are subject to technical modification without prior

notice.

All information in this document is subject to change without notice.

TABLE OF CONTENTS

1INSTALLATION............................................................................................................................... 2

1.1 TRS 05 mounting......................................................................................................................... 2

1.2 Install patch cable assembly........................................................................................................ 2

1.3 A2b switch mounting ................................................................................................................... 2

2SYSTEM DESCRIPTION................................................................................................................ 3

2.1 Receiver Module.......................................................................................................................... 3

2.1.1 LEDs .....................................................................................................................................................3

2.1.2 Control Identification .............................................................................................................................4

3OPERATION ................................................................................................................................... 5

3.1 Receiver ...................................................................................................................................... 5

4SETUP A SENSOR/MENU OPTIONS............................................................................................ 6

4.1 Install Sensor / Transmitter.......................................................................................................... 6

4.2 Uninstall Sensor / Transmitter ..................................................................................................... 7

5INSTALLATION............................................................................................................................... 8

5.1 Receiver ...................................................................................................................................... 8

6SPARE PART NUMBERS ..............................................................................................................9

Installation/Setup Manual DS 85 / TRS 05

1 INSTALLATION

1.1 TRS 05 MOUNTING

The TRS 05 receiver will mount in the same place as the A2B receiver. Attach the 13ft long antenna

base and whip to the TRS 05; and mount the magnetic antenna parallel to the ground, as shown

below.

1.2 INSTALL PATCH CABLE ASSEMBLY

Install patch cable assembly in between the TRS05 and LMI cable harness. The patch cable connects

power, ground, and A2B signal to the TRS05 and LMI.

1.3 A2B SWITCH MOUNTING

Replace the existing switch at the boom tip with the new 6608125 radio A2B switch/transmitter,

PATB3 with the spread spectrum technology.

System Description

2 SYSTEM DESCRIPTION

2.1 RECEIVER MODULE

The receiver module has the following functions:

•Visual indication of receiver power, radio links (sensor on line), sensors low battery, and alarm

conditions.

•Installs/uninstalls a sensor

•Allows a zero point and output adjustment of a load sensor.

Red Power LED

Red Alarm LED

Sensor On Line

Green LED 1

Green LED 2

Green LED 3

Green LED 4

Sensor Low Battery

Yellow LED 1

Yellow LED 2

Yellow LED 3

Yellow LED 4

2.1.1 LEDs

Red Power LED Power is applied to the circuit board.

Red alarm LED An installed sensor is indicating an alarm, or communication as been

lost to an installed sensor.

Green LED 1 ON Sensor on channel #1 is installed and communicating correctly.

Green LED 1 FLASHING Sensor #1 is not communicating correctly.

Green LED 1 OFF No sensor is installed on channel #1.

Yellow LED 1 ON Sensor #1 batteries are low and need replaced. Note that the sensor

is still operating correctly.

Green LED 2 ON Sensor #2 is installed and communicating correctly.

Green LED 2 FLASHING Sensor #2 is not communicating correctly.

Green LED 2 OFF No sensor is installed on channel #2.

Yellow LED 2 ON Sensor #2 batteries are low and need replaced. Note that the sensor

is still operating correctly.

Installation/Setup Manual DS 85 / TRS 05

Green LED 3 ON Sensor #3 is installed and communicating correctly.

Green LED 3 FLASHING Sensor #3 is not communicating correctly.

Green LED 3 OFF No sensor is installed on channel #3.

Yellow LED 3 ON Sensor #3 batteries are low and need replaced. Note that the sensor

is still operating correctly.

Green LED 4 ON Sensor #4 is installed and communicating correctly.

Green LED 4 FLASHING Sensor #4 is not communicating correctly.

Green LED 4 OFF No sensor is installed on channel #4.

Yellow LED 4 ON Sensor #4 batteries are low and need replaced. Note that the sensor

is still operating correctly.

Green Heartbeat LED This will flash during normal operation. If it is a solid or off, the

receiver has a software error or the board has a component failure.

2.1.2 Control Identification

Sensor #1 output jumper J4

Sensor #2 output jumper J3

Sensor #3 output jumper J2

Sensor #4 output jumper J1

ID button

power (red), sensor link 1-4 left

to right (green)

LEDS

1-4 left to right (yellow)

LEDS Green Heartbeat LED

(located just under radio module)

software chip

radio module 031-300-300-024

Heartbeat LED: When blinking, this small surface board mounted green LED indicates the system is

operation properly.

ID button: The red ID button, located below the software chip on the receiver board, is used to setup

the sensor transmitter to the receiver.

Operation

3 OPERATION

3.1 RECEIVER

Upon switching on crane ignition switch, the system starts with an automatic test of the receiver board,

LEDs and electronic components. The red power LED should be on and the green LEDs that sensors

have been linked to should also be on.

If an alarm condition exists investigate and clear the condition before operation and using the system.

During the normal operation of the system, the POWER and SENSOR ON LINE (if linked to a sensor)

LEDs should be on.

POWER LED

The POWER LED shows that the receiver is getting power from the crane. The receiver is on any time

the crane is operating and supplying power to the system.

SENSOR ON LINE LED

The SENSOR ON LINE LED indicates the status of communication of the transmitter(s). During

normal operation of the system, the LED will be on. The LED will flash if communication or

transmission between the sensor transmitter and the receiver is interrupted or lost. The system should

not be operated if the SENSOR ON LINE LED is flashing. If the LED is off no sensor is linked to this

channel.

LOW BATTERY LED

The low battery indicator (yellow LED) will light indicating that you have a limited time to operate

before the sensor battery life ends. When a low battery condition occurs, the follow 2 conditions will

exist:

1. The yellow LED will come on the TRS 05 for the sensor.

2. The signal for that sensor will cycle between input signal and max signal, which causes a

system fault and alarm for 25 seconds. The intent is to warn the operator that something is not

correct with the system. If the receiver is powered off/on and the low battery condition exists,

the signal will again cycle for another 25 seconds.

When the battery level is to the point that it is too low to operate, the system will display a loss of

communication and alarm. Use any off-the-shelf alkaline C-cells; Duracell, Eveready, etc. After

replacing the transmitter batteries, the receiver should clear the low battery indication.

ALARM LED

This LED will light simultaneously with the engaging of the lock out solenoids (if installed).

Installation/Setup Manual DS 85 / TRS 05

Test the electronics

Cycle the power to the system, each LED on the receiver will light for 2 seconds when the system is

powered. All of the indicator lights must come on or the system is not functioning properly. If any light

does not function, do not use the system until it has been repaired.

Refer to receiver operating manual for pre-operational inspection.

If a green sensor on line LED starts to flash, this means a sensor is installed and the communication

link has been lost. When communication has been lost to a load cell, the receiver will output the

maximum voltage signal for the output sensor (9VDC).

If a low battery LED is on, replace the batteries in the linked transmitter, refer to Battery Replacement.

The TRS 05 setup/calibration procedure allows the operator to input the type of sensors being used,

and adjust the zero point and output adjustment of a load sensor. The operator must complete the

setup procedure for each sensor.

4 SETUP A SENSOR/MENU OPTIONS

While the ID button is held or in the calibration process, the sensor outputs will not correctly indicate

the status of other installed sensors. Correct operation will return when the menu is exited or

calibration process is complete or system is powered off/on.

The sensor setup and calibration is completed with the one ID button, pressing it starts the menu and

releasing the button selects the menu or action the operator want to complete. If an incorrect menu is

activated or the button is released accidentally, simply cycle the power and start over.

4.1 INSTALL SENSOR / TRANSMITTER

Press and hold the ID button for 3-5 second the 1st green LEDs will begin blinking. If the button is held

for 3-5 more seconds the 2nd LED will begin to blink, continue holding the button and the setup

program will cycle through the 4 sensor channels. When the correct LED is blinking, channel to be

installed, release the ID button, the receiver begins to search for a transmitter ID code. The green LED

will become solid when the transmitter is linked.

As the ID button is held and released at the blinking LED, the following actions will occur:

Green LED 1 Blinking: Search for / Install sensor 1. LED will turn solid when the sensor is found.

Green LED 2 Blinking: Search for / Install sensor 2. LED will turn solid when the sensor is found.

NOTE: A new sensor or transmitter maybe install over an existing link, when this occurs the previous

link and code are removed from memory and the new one stored.

Setup a Sensor/Menu Options

4.2 UNINSTALL SENSOR / TRANSMITTER

If a sensor is setup on the channel the LED will be on, press and hold the ID button (16-28 seconds)

through the Install Sensor mode (blinking LEDs1-4) until the correct 1-4 LED is solid. When the correct

LED is solid, channel to be uninstalled, release the ID button. The sensor for the selected

channel/LED 1-4 will be uninstalled and the system will be in normal operating mode.

As the ID button is held (16-28 seconds) through the Install Sensor mode (blinking LEDs1-4) and

released at the solid LED, the following actions will occur:

Green LED 1 solid: Uninstall sensor 1.

Green LED 2 solid: Uninstall sensor 2.

Green LED 3 solid: Uninstall sensor 3.

Green LED 4 solid: Uninstall sensor 4.

This is a basic overview table of the menu selections fro the TRS 05. Press and hold ID button,

release the button at the desired indication (or the number seconds) defined in the following table.

NOTE: If an incorrect menu is activated or the button is released accidentally, simply cycle the power

and start over.

Menu Selection Release ID Button Indication

Indication

Starts

(Sec)

Indication

Ends

(Sec)

Install/setup sensor on channel 1 blinking green LED 1 3 6

Install/setup sensor on channel 2 blinking green LED 2 6 9

Install/setup sensor on channel 3 blinking green LED 3 9 12

Install/setup sensor on channel 4 blinking green LED 4 12 15

Uninstall a sensor on channel 1 solid LED 1 16 19

Uninstall a sensor on channel 2 solid LED 2 19 22

Uninstall a sensor on channel 3 solid LED 3 22 25

Uninstall a sensor on channel 4 solid LED 4 25 28

Set all the analog outputs for voltage 0-5V All 4 green LEDs blinking 29 32

Set all the analog outputs for 4..20ma All 4 green LEDs solid 33 36

Set all the analog outputs for voltage 1-9V All 4 yellow LEDs blinking 37 40

Set all the analog outputs for voltage 0-9V All 4 yellow LEDs solid 40 43

Calibrate load/angle sensor on channel 1 blinking yellow & green LEDs 1 43 46

Calibrate load/angle sensor on channel 2 blinking yellow & green LEDs 2 46 49

Calibrate load/angle sensor on channel 3 blinking yellow & green LEDs 3 50 53

Calibrate load/angle sensor on channel 4 blinking yellow & green LEDs 4 53 56

Service information on channel 1 blinking yellow LED 1 56 59

Service information on channel 2 blinking yellow LED 2 59 63

Service information on channel 3 blinking yellow LED 3 63 66

Service information on channel 4 blinking yellow LED 4 67 70

Exit/No action LEDs off no 71

Installation/Setup Manual DS 85 / TRS 05

5 INSTALLATION

5.1 RECEIVER

The receiver module should be mounted so the operator can view the LEDs and setup the system for

operation. The location of the receiver should be in direct line of site of the transmitter and blocked by

as little metal as possible between the transmitter and receiver. However, in some cases the receiver

has been installed surrounded by metal and worked well. The location needs to be tested before

mounting the hardware. If the signal is lost, the box/receiver indicates a link error.

Securely attach the receiver onto a solid surface using the mounting holes.

Power cable connections are show above.

Model: PAT TRS 05

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept interference that may

cause undesired operation.

ALARM

POWER

SENSOR LOW BATTERY

SENSOR ON LINE

2 3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hirschmann Récepteur

Hirschmann

Hirschmann OEV 801-E BFOC Manuel

Hirschmann

Hirschmann CSR 50 FTA Manuel utilisateur

Hirschmann

Hirschmann QPE 8600 Manuel utilisateur

Hirschmann

Hirschmann PAT TRS 05 Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur