Hills NVC-BM1 Manuel utilisateur
3MP IR Bullet Camera (4mm)
NVC-BM1
Quick Guide
V1.3
Quick Guide Bullet Camera
2
2
Table of Contents
Overview .............................................................................................................3
Installation ..........................................................................................................5
Setup using Hills’ NVR .........................................................................................8
Setup using remote software ..............................................................................9
Specifications ....................................................................................................13
Quick Guide Bullet Camera
3
3
1
Figure 1-1 Bullet camera overview
Table 1-1 Description
No.
Description
1
Adjustable Bracket
2
Back Box
3
Front Box
4
Lens
5
Sun Shield
6
Power & Network cable
7
Grounding Screw
8
Reset
13
7
8
24
56
Overview
1
Quick Guide Bullet Camera
4
4
Hole Hole
Hole
Ceiling Mounting
Table 1-2 Carton contents
Camera
Quick Guide
Drill template
Mounting hardware
3x Expansion screws
Quick Guide Bullet Camera
5
5
Checklist before you start
All carton contents present and are in good conditions.
Ensure power supplies are off during installation.
Power supply voltage rating as specified in product specifications.
Installation environment is as specified.
Contact your dealer if product does not function properly. Do not attempt to
repair yourself.
Wall or mounting platform is strong enough to withstand three times the
weight of the camera.
Installation
2
Quick Guide Bullet Camera
6
6
Steps:
1. Attach the drill template on the wall.
Figure 2-1 Attach the template
2. Secure the camera to the ceiling with the supplied expansion mounting.
Figure 2-2 Secure the camera to the ceiling
Ceiling Mounting
Hole
Hole
Hole
Quick Guide Bullet Camera
7
7
3. Adjust the field of view
1). Loosen the adjustable nut on the bracket.
2). Adjust the panning angle [0~360°] of the camera.
3). Adjust the tilting angle [0~90°] of the camera.
4). Rotate 0~360° to adjust angle of the image.
5). Tighten the adjustable nut to complete the installation.
Figure 2-3 3-axis adjustment
0°~360°
0°~90°
0°~360°
Quick Guide Bullet Camera
8
8
Setup using Hills’NVR
The Hills Video Security IP cameras (NVC-MB1, NVC-DM1, NVC-DT1 and
NVC-DF1) have a pre-loaded protocol that works immediately with Hills Video
Security NVRs (NVR-CH4, NVR-CH8 and NVR-CH16) as soon as they are
connected.
Connect the camera via a network cable to one of the PoE network interface
sockets at the back of the NVR.
Figure 3-1 NVR –Camera connection
Please refer to User Manual of NVR to add and edit a camera.
Setup using Hills’NVR
3
Quick Guide Bullet Camera
9
9
etup using remote software
To view and configure the camera via LAN (Local Area Network), you need to
connect the network camera in the same subnet with your PC. Then install
the PC client software to search and change the IP address of the network
camera.
The following figure shows the cable connection of a network camera and a
PC:
Figure 4-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
1. Use PC Client software to detect the online devices. Please refer to the
user manual of PC client software for detailed information.
●Search online devices automatically
After launching the PC Client software, it automatically searches the online
devices every 15 seconds from the subnet where your computer is located.
Setup using remote software
4
Quick Guide Bullet Camera
10
10
It displays the total number and information of the searched devices in the
Online Devices interface.
Go to Device Management, and click Server tab on the top-left of the
window, and you can see the online devices listed on the bottom right of
the window.
Figure 4-2 Search online devices
Note:
Devices can be searched and displayed in the list in 15 seconds after they go
online; they will be removed from the list in 45 seconds after it went offline.
●Search online devices manually
You can also click to refresh the online device list
manually. The newly searched devices will be added to the online list.
2. Change the IP address and subnet mask to the same subnet as of your
PC.
Steps:
1). Click the device to be modified in the device list and click
to modify the network parameters.
Autres manuels pour NVC-BM1
2
Table des matières
Autres manuels Hills Caméra de sécurité
