HIK VISION DS-KH6320-WTE1 Manuel utilisateur
Network Indoor Staon
Installaon Guide
Symbol Convenons
The symbols that may be found in this document are dened as follows.
Symbol Descripon
Danger Indicates a hazardous situaon which, if not avoided, will or
could result in death or serious injury.
Cauon Indicates a potenally hazardous situaon which, if not
avoided, could result in equipment damage, data loss,
performance degradaon, or unexpected results.
Note Provides addional informaon to emphasize or
supplement important points of the main text.
Network Indoor Staon Installaon Guide
i
Contents
1 Appearance ................................................................................................ 1
2 Terminal and Wiring Descripon ................................................................ 3
2.1 Terminal Descripon ......................................................................................... 3
2.2 Wiring Descripon ............................................................................................ 3
3 Installaon .................................................................................................. 5
3.1 Wall Mounng Plate ......................................................................................... 5
3.2 Wall Mounng with Juncon Box ..................................................................... 5
A. Cables ........................................................................................................ 7
Network Indoor Staon Installaon Guide
ii
1 Appearance
Front Panel
Figure 1-1 Front Panel
Table 1-1 Descripon
No. Descripon
1 Display Screen
2 Microphone
Network Indoor Staon Installaon Guide
1
Rear Panel
Figure 1-2 Rear Panel
Table 1-2 Descripon
No. Descripon
3 Debugging Port
4 Network Interface
5 Loudspeaker
6 TF Card Slot
7 Alarm Terminal
8 Reserved
9 Network Interface and Power Supply
Note
The debugging port is used for debugging only.
Network Indoor Staon Installaon Guide
2
2 Terminal and Wiring Descripon
2.1 Terminal Descripon
There are 20 pins in the terminal on the rear panel of the indoor staon: 2 RS-485
pins, 5 reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.
Figure 2-1 Terminal Descripon
2.2 Wiring Descripon
Wire the devices with power supply cables as picture shown below.
Door staon should be connected to CH6 of the video/audio distributor with two-
wire cables.
Indoor Staon should be connected to any terminal of CH1 to CH5 of the video/
audio distributor with two-wire cables.
Cauon
Make sure all the related equipment is power-o during the installaon.
Network Indoor Staon Installaon Guide
3
Figure 2-2 Wiring Descripon
Network Indoor Staon Installaon Guide
4
3 Installaon
Indoor staon supports wall mounng.
3.1 Wall Mounng Plate
The wall mounng plate and the juncon box are required to install the indoor
staon onto the wall.
The dimension of juncon box should be 75 mm (width) × 75 mm (length) × 50 mm
(depth).
The dimension of wall mounng plate is shown.
Figure 3-1 Wall Mounng Plate
3.2 Wall Mounng with Juncon Box
Network Indoor Staon Installaon Guide
5
Before You Start
Note
•Make sure the device in the package is in good condion and all the assembly
parts are included.
•The power supply the indoor staon supports is 12 VDC. Please make sure your
power supply matches your indoor staon.
•Make sure all the related equipment is power-o during the installaon.
•Check the product specicaon for the installaon environment.
Steps
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncon box to the hole chiseled on the wall.
3. Fix the wall mounng plate to the juncon box with 2 screws.
4. Hook the indoor staon to the wall mounng plate ghtly by inserng the plate
hooks into the slots on the rear panel of the indoor staon, during which the
lock catch will be locked automacally.
Figure 3-2 Wall Mounng with Juncon Box
Network Indoor Staon Installaon Guide
6
A. Cables
Table A-1 Wiring Cables
Roung Path Twisted Pair :
24AWG
(0.2mm²)
Twisted Pair :
20AWG
(0.5mm²)
Twisted Pair :
18AWG
(0.8mm²)
Parallel Cable :
≥ 24AWG (0.22
mm²)
DS-KAD706 -
DS-KAD706-S
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-S -
DS-KAD706-S
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-
DS-KD8003-
IME2
Transmission
Distance ≤ 35
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
DS-KAD706-
DS-KH6320-
WTE2
Transmission
Distance ≤ 35
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 60
m
Transmission
Distance ≤ 35
m
Network Indoor Staon Installaon Guide
7
Autres manuels pour DS-KH6320-WTE1
4
Table des matières
Autres manuels HIK VISION Système d'interphone
HIK VISION
HIK VISION DS-KIS702Y Manuel utilisateur
HIK VISION
HIK VISION DS-KM8301 Manuel utilisateur
HIK VISION
HIK VISION Villa 6 Series Manuel utilisateur
HIK VISION
HIK VISION DS-KB8113-IME1(B) Series Manuel utilisateur
HIK VISION
HIK VISION DS-KD8003-IME1 Manuel utilisateur
HIK VISION
HIK VISION DS-K3B802X Series Manuel utilisateur
HIK VISION
HIK VISION HYU-559 Manuel utilisateur
HIK VISION
HIK VISION DS-KV6113-PE1 Manuel utilisateur
HIK VISION
HIK VISION DS-KB2421-IM Manuel utilisateur
HIK VISION
HIK VISION KD94X3 Manuel utilisateur
HIK VISION
HIK VISION DS-KH8520-WTE1 Manuel utilisateur
HIK VISION
HIK VISION DS-KH9510-WTE1 Manuel utilisateur
HIK VISION
HIK VISION DS-KH6100-E1 Manuel utilisateur
HIK VISION
HIK VISION DS-KD8102 Manuel utilisateur
HIK VISION
HIK VISION DS-KD9613-FE6 Manuel utilisateur
HIK VISION
HIK VISION DS-KH6350-TE1 Manuel utilisateur
HIK VISION
HIK VISION DS-KH6310-W Manuel utilisateur
HIK VISION
HIK VISION DS-KH9510-WTE1 Manuel utilisateur
HIK VISION
HIK VISION DS-KB8113-IME1(B) Series Manuel utilisateur
HIK VISION
HIK VISION DS-KIS212 Manuel utilisateur
